ASTM B224-2010 Standard Classification of Coppers《铜的标准分类》.pdf

《ASTM B224-2010 Standard Classification of Coppers《铜的标准分类》.pdf》由会员分享，可在线阅读，更多相关《ASTM B224-2010 Standard Classification of Coppers《铜的标准分类》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B224 10Standard Classification ofCoppers1This standard is issued under the fixed designation B224; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year o

2、f last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This is a classification of the various types of coppercurrently available in refinery shapes and wrought products incommercial quantities. It is not a specification for the va

3、rioustypes of copper.1.2 In this classification, use is made of the standard copperdesignations in use by the copper industry.1.3 Although this classification includes certain UNS des-ignations as described in Practice E527, these designations arefor cross-reference only and are not requirements. Th

4、erefore, incase of conflict, this ASTM classification shall govern.1.4 This classification does not attempt to differentiatebetween all compositions that could be termed either coppersor copper-base alloys, but in conformance with general usagein the trade, includes those coppers in which the copper

5、 isspecified as 99.85 % or more, silver being counted as copper.NOTE 1Coppers may contain small amounts of certain elementsintentionally permitted to impart specific properties, without excessivelylowering electrical conductivity. The total copper plus specific permittedelements is usually specified

6、 as 99.85 % or more. These intentionallypermitted elements normally include, but are not limited to, arsenic,cadmium, chromium, lead, magnesium, silver, sulfur, tellurium, tin, zinc,and zirconium, plus deoxidizers, up to specific levels adopted by theInternational Standards Organization.1.5 UnitsThe

7、 values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units, which are provided forinformation only and are not considered standard.2. Referenced Documents2.1 ASTM Standards:2E527 Practice for Numbering Metals and Alloys i

8、n theUnified Numbering System (UNS)B846 Terminology for Copper and Copper Alloys3. Terminology3.1 This classification covers definitions specific to thisdocument and in conjunction with B846.3.2 Definitions of Terms Specific to This Standard:3.2.1 sulfur-bearing copperCopper alloy containing aspecif

9、ied amount of sulfur (C14700).3.2.2 tellurium-bearing copperCopper alloy containing aspecified amount of tellurium (C14500).3.2.3 wirea solid section, including rectangular flat wirebut excluding other flat products, furnished in coils or onspools, reels, or bucks.3.2.4 zirconium-bearing copperCoppe

10、r alloy containing aspecified amount of zirconium (C15000).4. Significance and Use4.1 This classification lists the types of copper availablefrom refineries or fabricators, or both, defines the commonterms used, and gives the characteristics of many of thecoppers available. It is useful to the neoph

11、yte looking for theappropriate copper for a particular application.5. Basis of Classification5.1 Table 1 lists the standard designations, and the refineryshapes and fabricators products currently produced. The listedcoppers are not necessarily available in the complete range ofsizes in the form show

12、n, nor from any one supplier in all forms.5.2 Existing ASTM specifications for refinery copper andfor wrought copper products may cover more than one of thecoppers listed in Table 1 or may include only part of the rangecovered by any one of the coppers shown in this classification.6. Keywords6.1 cla

13、ssification, coppers1This classification is under the jurisdiction of ASTM Committee B05 onCopper and Copper Alloys and is the direct responsibility of Subcommittee B05.07on Refined Copper.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 1948. Last previous editi

14、on approved in 2004 as B224 04. DOI:10.1520/B0224-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summ

15、ary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee B05 has identified the location of selected changes to this standard since the last issue (B224 04)

16、that may impact the use of this standard. (Approved Oct. 1, 2010.)(1) Removed definitions which are also listed in B846.(2) Editorial changes related to removal of definitions.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item menti

17、onedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee a

18、nd must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting

19、of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Bo

20、x C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Perm

21、ission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Classification of CoppersNOTE 1Table 1 lists the standard designations, refinery shapes, and fabricators products.DesignationsType of CopperAUNS Nos.BForm in which Copper is AvailableC

22、From Refiners From FabricatorsAWire Bars Billets CakesIngotsandIngotBarsFlat ProductsPipeandTubeRodandWireShapesCATH Electrolytic cathode Cathodes onlyTough-Pitch CoppersETP Electrolytic tough-pitch C11000 X X X X X X X XRHC Remelted, high-conductivity tough pitch C11010 X X X X X X X XETP Electroly

23、tic tough-pitch (anneal resist) C11100 X X X X X X XFRHC Fire-refined, high-conductivity tough-pitch C11020 X X X X X X X XSTP Silver-bearing, tough-pitch C11300, C11400, C11500, C11600 X X X X X X X XFRTP Fire-refined, tough-pitch C12500 X X X X X X XFRSTP Fire-refined tough-pitch with silver C1290

24、0 X X X X XOxygen-Free Coppers (Without use of Deoxidants)OFE Oxygen-free, electronic C10100 X X X X X X XOF Oxygen-free C10200 X X X X X X XOFS Oxygen-free, silver-bearing C10400, C10500, C10700 X X X X X X XOFXLP Oxygen-free, extra low phosphorus C10300 X X X X X X XOFLP Oxygen-free, low-phosphoru

25、s C10800 X X X X X X XDeoxidized CoppersDLP Phosphorized, low-residual phosphorus C12000 X X X X XDLPS Phosphorized, low-residual phosphorus silver- bearing C12100 X X X X XDHP Phosphorized, high-residual phosphorus C12200 X X X X X XDHPS Phosphorized, high-residual phosphorus silver- bearing C12300

26、 X X X XDPTE Phosphorized, tellurium-bearing C14520 X XOther CoppersSulfur-bearing C14700 X XZirconium-bearing C15000 X X X XPTE Tellurium-bearing C14500 X XASee 3.1.BThe chemical compositions associated with these numbers are listed in the product specifications and in the Standard Designations for Copper and CopperAlloys thatappear in this publication under “Related Material”.CThe “X” in the table indicates commercial availability.B224 102