ASTM A760 A760M-2015 Standard Specification for Corrugated Steel Pipe Metallic-Coated for Sewers and Drains《下水道和排水沟用金属涂覆的波纹钢管标准规格》.pdf

《ASTM A760 A760M-2015 Standard Specification for Corrugated Steel Pipe Metallic-Coated for Sewers and Drains《下水道和排水沟用金属涂覆的波纹钢管标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A760 A760M-2015 Standard Specification for Corrugated Steel Pipe Metallic-Coated for Sewers and Drains《下水道和排水沟用金属涂覆的波纹钢管标准规格》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A760/A760M 13A760/A760M 15Standard Specification forCorrugated Steel Pipe, Metallic-Coated for Sewers andDrains1This standard is issued under the fixed designation A760/A760M; the number immediately following the designation indicates the yearof original adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers corrugated steel pipe intended for use for storm water drainage, underdrai

3、ns, the construction ofculverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrialwastes. The steel sheet used in fabrication of the pipe has a protective metallic coating of zinc (galvanizing), aluminum, 55 %aluminum-zinc alloy, o

4、r zinc-5 % aluminum-mischmetal alloy.1.2 The several different metallic coatings may not provide equal protection of the base metal against corrosion or abrasion inall environments, or both. Some environments may be so severe that none of the metallic coatings included in this specificationwill prov

5、ide adequate protection. Additional protection for corrugated steel pipe can be provided by use of coatings applied afterfabrication of the pipe as described in Specification A849, or by use of polymer precoated corrugated steel pipe as described inSpecification A762/A762M.1.3 Section 9 is intended

6、to be applied to corrugated steel pipe joints. The several different types of corrugated steel pipe jointsprovide various qualities. This specification is not intended for routine quality control testing or in-field acceptance testing, but isintended to establish performance limits of the pipe joint

7、s, as well as the test requirements and test methods for the joints asdescribed herein.1.4 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheetthickness of the pipe. Experience has shown that the successful performance of this

8、 product depends upon the proper selection ofsheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The installationprocedure is described in Practice A798/A798M.1.5 This specification is applicable to orders in either inch-pound units as A7

9、60 or in SI units as A760M. Inch-pound units andSI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values whenthe material is ordered to A760M.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of

10、Coating on Iron and Steel Articles with Zinc or Zinc-Alloy CoatingsA153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareA307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile StrengthA428/A428M Test Method for Weight Mass of Coating on Aluminum

11、-Coated Iron or Steel ArticlesA449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength,General UseA563 Specification for Carbon and Alloy Steel NutsA563M Specification for Carbon and Alloy Steel Nuts (Metric)A742/A742M Specification for Ste

12、el Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel PipeA762/A762M Specification for Corrugated Steel Pipe, Polymer Precoated for Sewers and DrainsA780 Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings1 This specification is under the jurisdiction ofAS

13、TM Committee A05 on Metallic-Coated Iron and Steel Products and is the direct responsibility of Subcommittee A05.17on Corrugated Steel Pipe Specifications.Current edition approved Nov. 1, 2013May 1, 2015. Published November 2013May 2015. Originally approved in 1979. Last previous edition approved in

14、 20102013 asA760/A760M - 10.A760/A760M - 13. DOI: 10.1520/A0760_A0760M-13.10.1520/A0760_A0760M-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Docum

15、ent Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM re

16、commends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1A796/A796M

17、Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewersand Other Buried ApplicationsA798/A798M Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other ApplicationsA849 Specification for Post-Applied Coatings, Pavings, and

18、 Linings for Corrugated Steel Sewer and Drainage PipeA929/A929M Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel PipeB633 Specification for Electrodeposited Coatings of Zinc on Iron and SteelB695 Specification for Coatings of Zinc Mechanically Deposited on I

19、ron and SteelC1619 Specification for Elastomeric Seals for Joining Concrete StructuresD1056 Specification for Flexible Cellular MaterialsSponge or Expanded RubberF568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric) (Withdrawn 2012)32.2 AASHTO Standards:4T241 T

20、est for Helical Continuous Welded Seam Corrugated Steel PipeT249 Test for Helical Lock Seam Corrugated Pipe3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 fabricatorthe producer of the pipe.3.1.2 manufacturerthe producer of the sheet.3.1.3 minimized coating structurea coating

21、characterized by a finer metallurgical coating structure obtained by a treatmentdesigned to restrict the formation of the normal coarse-grain structure formed during solidification of the Zn-5 Al-MM alloycoating.3.1.4 purchaserthe purchaser of the finished product.3.1.5 regular coating structurethe

22、normal coating structure resulting from unrestricted grain growth during normalsolidification of the Zn-5 Al-MM alloy coating.3.2 Abbreviations:3.2.1 55 Al-Zn55 % aluminum-zinc.3.2.2 MMmischmetal.3.2.3 Zn-5 Al-MMzinc-5 % aluminum-mischmetal.4. Classification4.1 The corrugated steel pipe covered by t

23、his specification is classified as follows:4.1.1 Type IThis pipe shall have a full circular cross section, with a single thickness of corrugated sheet, fabricated withannular (circumferential) or helical corrugations.4.1.2 Type IAThis pipe shall have a full circular cross section, with an outer shel

24、l of corrugated sheet and an inner liner ofsmooth (uncorrugated) sheet, fabricated with helical corrugations and lock seams.4.1.3 Type IRThis pipe shall have a full circular cross section with a single thickness of smooth sheet, fabricated with helicalribs projecting outwardly.4.1.4 Type ISThis pipe

25、 shall have a full circular cross section with a single thickness of smooth sheet, fabricated with helicalribs projecting outwardly, and shall also have metallic-coated steel inserts placed in the ribs so that the inside surface of the pipeis essentially smooth.4.1.5 Type IIThis pipe shall be a Type

26、 I pipe which has been reformed into a pipe-arch, having an approximately flat bottom.4.1.6 Type IIAThis pipe shall be a Type IA pipe which has been reformed into a pipe-arch, having an approximately flatbottom.4.1.7 Type IIRThis pipe shall be a Type IR pipe which has been reformed into a pipe-arch,

27、 having an approximately flatbottom.4.1.8 Type IISThis pipe shall be a Type IS pipe which has been reformed into a pipe-arch, having an approximately flatbottom.4.1.9 Type IIIThis pipe, intended for use as underdrains or for underground disposal of water, shall be a Type I pipe whichhas been perfora

28、ted to permit the inflow or outflow of water.4.1.10 Type IIIAThis pipe, intended for use as underdrains, shall consist of a semicircular cross section, having a smooth(uncorrugated) bottom with a corrugated top shield.4.2 Perforations in Type III pipe are included in three classes as described in 8.

29、3.2.3 The last approved version of this historical standard is referenced on www.astm.org.4 Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,http:/www.transportation.org.A760/A760M 1524.3 Zn-5 Al-MM al

30、loy-coated material is available in two coating classes, or structures, as follows:4.3.1 Class AMinimized coating structure.4.3.2 Class BRegular coating structure.5. Ordering Information5.1 Orders for material to this specification shall include the following information as necessary, to adequately

31、describe thedesired product.5.1.1 Name of material (corrugated steel pipe),5.1.2 Type of metallic coating (zinc, aluminum, 55 Al-Zn alloy, Zn-5 Al-MM alloy (see 6.1).5.1.2.1 For Zn-5A1-MM coating, the class coating structure (Class A minimized, etc.) (4.3).5.1.3 ASTM designation and year of issue, a

32、s A760-_ for inch-pound units or as A760M-_ for SI units.5.1.4 Type of pipe (4.1),5.1.5 Diameter of circular pipe (Table 1), or span and rise of pipe-arch section (Tables 2-9),5.1.6 Length, either total length or length of each piece and number of pieces,5.1.7 Description of corrugations (7.2),5.1.8

33、 Sheet thickness (8.1.2),5.1.9 For Type I and Type II pipe, the pipe fabrication method, whether with annular corrugations or helical corrugations (see7.1.1),NOTE 1Pipe with annular corrugations with spot welded or riveted seams is designed by different criteria compared to pipe with helical corruga

34、tions.Pipe with annular corrugations must consider seam strength. Therefore, consideration of the method of fabrication is important when pipe is installedunder certain conditions of loading.5.1.10 ForTypes IS and IIS pipe, the type of insert required, whether from metallic coated steel sheet or fro

35、m polymer-precoatedmetallic-coated steel sheet (see 6.6 and 8.1.2).NOTE 2Aluminized steel Type 2 inserts are not available with a polymer coatingNOTE 3See Specification A849 for additional ordering information appropriate to post-coatings on pipe.TABLE 1 Pipe SizesNominalInsideDiameterCorrugation Si

36、zesA Ribbed PipeMinimumOutsideCircumferenceBin. mm 112 by 14 in.38 by 6.5 mm 223 by 12 in.68 by 13 mm 3 by 1 in.75 by 25 mm 5 by 1 in.125 by 25 mm 34 by 34 by 712 in.19 by 19 by 190 mm 34 by 1 by 1112 in.19 by 25 by 292 mm 34 by 1 by 812 in.19 by 25 by 216 mm in. mm4 100 X 11.4 2646 150 X 17.7 4418

37、200 X 24.0 59810 250 X 30.2 75512 300 X X 36.5 91215 375 X X XC 46.0 114818 450 X X X X X 55.4 138321 500 X X X X 64.8 162024 600 X X X X 74.2 185427 675 X X X X 83.6 209130 750 X X X X 93.1 248333 825 X X X X 102.5 256136 900 X X X X X X 111.9 279742 1050 X X X X X X 130.8 326948 1200 X X X X X X 1

38、49.6 373954 1350 X X X X X X 168.4 420960 1500 X X X X X X 187.0 467566 1650 X X X X X X 205.7 514272 1800 X X X X X X 224.3 560978 1950 X X X X X X 243.0 607584 2100 X X X X X X 261.7 654290 2250 X X X X X 280.3 700896 2400 X X X X X 299.0 7475102 2550 X X X X X 317.6 7941108 2700 X X X X X 336.3 8

39、408114 2850 X X X X 355.0 8874120 3000 X X X X 373.6 9341126 3150 X X X 392.3 9807132 3300 X X X 410.9 10274138 3450 X X X 429.6 10740144 3600 X X X 448.3 11207AAn“ X” indicates standard corrugation sizes for each nominal diameter of pipe.BMeasured in valley of annular corrugations. Not applicable t

40、o helically corrugated pipe.CAdditional size for Type IS pipe.A760/A760M 1535.1.11 Joining systems, including the type of joint from 9.2 and gasket, if required (If no joining system is specified, thefabricator shall select a soil tight joining system.),5.1.12 For Type III pipe, class of perforation

41、s, if other than Class 1 (8.3.2),5.1.13 Certification, if required (14.1), and5.1.14 Special requirements.6. Materials and Manufacture6.1 Steel Sheet for PipeAll pipe fabricated under this specification shall be formed from zinc-coated sheet, aluminum-coatedsheet, 55 % aluminum-zinc alloy-coated she

42、et, zinc-5 % aluminum-mischmetal alloy-coated sheet all conforming to SpecificationA929/A929M. If the type of metallic coating is not stated in the order, zinc-coated sheet conforming to Specification A929/A929Mshall be used. All pipe furnished on the order shall have the same metallic coating, unle

43、ss otherwise specified.6.2 Steel Sheet for Coupling BandsThe sheet used in fabricating coupling bands shall have the same coating and shall conformto the same specification listed in 6.1 as that used for fabrication of the pipe furnished under the order.6.3 RivetsThe rivets used in riveted pipe shal

44、l be of the same material as the base metal specified for the corrugated sheets.They shall be thoroughly galvanized or sherardized. If bolts and nuts are substituted for rivets (see 7.3.1), they shall meet thefollowing requirements:Bolts NutsFor A760 pipe A449 A563, Grade CFor A760M pipe F568M, Clas

45、s 8.8 A563M, Class 12TABLE 2 Pipe Arch Requirements223 by 12-in. Corrugations(A760)Pipe ArchSize, in.EquivalentDiameter,in.Span,Ain.Rise,Ain.MinimumCornerRadius, in.MaximumB,B in.17 by 13 15 17 13 3 51421 by 15 18 21 15 3 624 by 18 21 24 18 3 71428 by 20 24 28 20 3 835 by 24 30 35 24 3 91242 by 29 3

46、6 42 29 312 101249 by 33 42 49 33 4 111257 by 38 48 57 38 5 131264 by 43 54 64 43 6 1571 by 47 60 71 47 7 161277 by 52 66 77 52 8 1883 by 57 72 83 57 9 20A A tolerance of 1 in. or 2 % of equivalent diameter, whichever is greater, ispermissible in span and rise.B B is defined as the vertical dimensio

47、n from a horizontal line across the widestportion of the arch to the lowest portion of the base.TABLE 3 Pipe Arch Requirements68 by 13-mmCorrugations A760MPipe ArchSize, mmEquivalentDiameter,mmSpan,AmmRise,AmmMinimumCornerRadius, mmMaximumB,B mm430 by 330 375 430 330 75 135530 by 380 450 530 380 75

48、155610 by 460 525 610 460 75 185710 by 510 600 710 510 75 205780 by 560 675 780 560 75 225885 by 610 750 870 630 75 240970 by 690 825 970 690 75 2551060 by 740 900 1060 740 90 2651240 by 840 1050 1240 840 100 2901440 by 970 1200 1440 970 130 3451620 by 1100 1350 1620 1100 155 3801800 by 1200 1500 18

49、00 1200 180 4201950 by 1320 1650 1950 1320 205 4602100 by 1450 1800 2100 1450 230 510A A tolerance of 25 mm or 2 % of equivalent diameter, whichever is greater, ispermissible in span and rise.B B is defined as the vertical dimension from a horizontal line across the widestportion of the arch to the lowest portion of the base.A760/A760M 154The bolts and nuts shall be hot-dip galvanized in conformance with Specification A153/A153M, or be mechanically galvanizedin conformance with Specification