书签分享收藏举报版权申诉 / 13

立即下载加入VIP,交流精品资源

当前位置：首页 > 标准规范 > 国际标准 > ASTM > ASTM A240 A240M-2009a Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate Sheet and Strip for Pressure Vessels and for General Applications.pdf

ASTM A240 A240M-2009a Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate Sheet and Strip for Pressure Vessels and for General Applications.pdf

上传人：confusegate185

文档编号：457780

上传时间：2018-11-25

格式：PDF

页数：13

大小：105.93KB

《ASTM A240 A240M-2009a Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate Sheet and Strip for Pressure Vessels and for General Applications.pdf》由会员分享，可在线阅读，更多相关《ASTM A240 A240M-2009a Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate Sheet and Strip for Pressure Vessels and for General Applications.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 240/A 240M 09aStandard Specification forChromium and Chromium-Nickel Stainless Steel Plate,Sheet, and Strip for Pressure Vessels and for GeneralApplications1This standard is issued under the fixed designation A 240/A 240M; the number immediately following the designation indicates the

2、 yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Depa

3、rtment of Defense.1. Scope*1.1 This specification2covers chromium, chromium-nickel,and chromium-manganese-nickel stainless steel plate, sheet,and strip for pressure vessels and for general applications.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as stand

4、ard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This specification is expressed in both inch-pound andSI units. However, unless t

5、he order specifies the applicable“M” specification designation (SI units), the material shall befurnished in inch-pound units.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish ap

6、pro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3A 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 480/A 480M Specification for General Requirements forFlat-Rolled Stain

7、less and Heat-Resisting Steel Plate,Sheet, and StripA 923 Test Methods for Detecting Detrimental IntermetallicPhase in Duplex Austenitic/Ferritic Stainless SteelsE112 Test Methods for Determining Average Grain SizeE 527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2

8、 SAE Standard:4J 1086 Practice for Numbering Metals and Alloys (UNS)3. General Requirements3.1 The following requirements for orders for materialfurnished under this specification shall conform to the appli-cable requirements of the current edition of SpecificationA 480/A 480M.3.1.1 Definitions;3.1.

9、2 General requirements for delivery;3.1.3 Ordering information;3.1.4 Process;3.1.5 Special tests;3.1.6 Heat treatment;3.1.7 Dimensions and permissible variations;3.1.8 Workmanship, finish and appearance;3.1.9 Number of tests/test methods;3.1.10 Specimen preparation;3.1.11 Retreatment;3.1.12 Inspecti

10、on;3.1.13 Rejection and rehearing;3.1.14 Material test report;3.1.15 Certification; and3.1.16 Packaging, marking, and loading.4. Chemical Composition4.1 The steel shall conform to the requirements as tochemical composition specified in Table 1 and shall conform toapplicable requirements specified in

11、 Specification A 480/A 480M.5. Mechanical Properties5.1 The material shall conform to the mechanical propertiesspecified in Table 2.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 o

12、n Flat-Rolled and Wrought Stainless Steel.Current edition approved April 1, 2009. Published April 2009. Originallyapproved in 1940. Last previous edition approved in 2008 as A 240/A 240M 09.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-240 in Section II of that

13、 Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from Society of Automotive Engineers (SAE),

14、400 CommonwealthDr., Warrendale, PA 15096-0001, http:/www.sae.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2 When specified by the purchaser, Charpy impact te

15、stsshall be performed in accordance with Supplementary Require-ment S1.6. Materials for High-Temperature Service6.1 The austenitic H Types shall conform to an averagegrain size of ASTM No. 7 or coarser as measured by TestMethods E112.6.2 Supplementary Requirement S2 shall be invoked whennon-H grade

16、austenitic stainless steels are ordered for ASMECode applications for service above 1000F 540C.6.3 Grade S31060, unless otherwise specified in the pur-chase order, shall conform to an average grain size of ASTMNo. 7 or coarser, as measured by Test Methods E112.7. Keywords7.1 chromium; chromium-nicke

17、l stainless steel; chromium-manganese-nickel stainless steel; pressure vesselsA 240/A 240M 09a2TABLE 1 Chemical Composition Requirements, %AUNSDesignationBTypeCCarbonDManganese Phos-phorusSulfur Silicon Chromium Nickel Molybdenum Nitrogen Copper OtherElementsE,FAustenitic (Chromium-Nickel) (Chromium

18、-Manganese-Nickel)N08020 . . . 0.07 2.00 0.045 0.035 1.00 19.021.0 32.038.0 2.003.00 . . . 3.04.0 Cb 83C min,1.00 maxN08367 . . . 0.030 2.00 0.040 0.030 1.00 20.022.0 23.525.5 6.07.0 0.180.25 0.75 . . .N08700 . . . 0.04 2.00 0.040 0.030 1.00 19.023.0 24.026.0 4.35.0 . . . 0.50 Cb 83Cmin0.40 maxN0880

19、0 800G0.10 1.50 0.045 0.015 1.00 19.023.0 30.035.0 . . . . . . 0.75 FeH39.5 minAl 0.150.60Ti 0.150.60N08810 800HG0.050.10 1.50 0.045 0.015 1.00 19.023.0 30.035.0 . . . . . . 0.75 FeH39.5 minAl 0.150.60Ti 0.150.60N08811 . . . 0.060.10 1.50 0.040 0.015 1.00 19.023.0 30.035.0 . . . . . . 0.75 FeH39.5 m

20、inTiI0.150.60AlI0.150.60N08904 904LG0.020 2.00 0.045 0.035 1.00 19.023.0 23.028.0 4.05.0 0.10 1.02.0 . . .N08926 . . . 0.020 2.00 0.030 0.010 0.50 19.021.0 24.026.0 6.07.0 0.150.25 0.51.5 . . .S20100 201 0.15 5.57.5 0.060 0.030 1.00 16.018.0 3.55.5 . . . 0.25 . . . . . .S20103 . . . 0.03 5.57.5 0.04

21、5 0.030 0.75 16.018.0 3.55.5 . . . 0.25 . . . . . .S20153 . . . 0.03 6.47.5 0.045 0.015 0.75 16.017.5 4.05.0 . . . 0.100.25 1.00 . . .S20161 . . . 0.15 4.06.0 0.040 0.040 3.04.0 15.018.0 4.06.0 . . . 0.080.20 . . . . . .S20200 202 0.15 7.510.0 0.060 0.030 1.00 17.019.0 4.06.0 . . . 0.25 . . . . . .S

22、20400 . . . 0.030 7.09.0 0.040 0.030 1.00 15.017.0 1.503.00 . . . 0.150.30 . . . . . .S20431 . . . 0.12 5.07.0 0.045 0.030 1.00 17.018.0 2.04.0 . . . 0.100.25 1.53.5 . . .S20432 . . . 0.08 3.05.0 0.045 0.030 1.00 17.018.0 4.06.0 . . . 0.050.20 2.003.00 . . .S20433 . . . 0.08 5.57.5 0.045 0.030 1.00

23、17.018.0 3.55.5 . . . 0.100.25 1.53.5 . . .S20910 XM-19J0.06 4.06.0 0.040 0.030 0.75 20.523.5 11.513.5 1.503.00 0.200.40 . . . Cb 0.100.30V 0.100.30S21400 XM-31J0.12 14.016.0 0.045 0.030 0.301.00 17.018.5 1.00 . . . 0.35 min . . . . . .S21600 XM-17J0.08 7.59.0 0.045 0.030 0.75 17.522.0 5.07.0 2.003.

24、00 0.250.50 . . . . . .S21603 XM-18J0.03 7.59.0 0.045 0.030 0.75 17.522.0 5.07.0 2.003.00 0.250.50 . . . . . .S21800 . . . 0.10 7.09.0 0.060 0.030 3.54.5 16.018.0 8.09.0 . . . 0.080.18 . . . . . .S24000 XM-29J0.08 11.514.5 0.060 0.030 0.75 17.019.0 2.33.7 . . . 0.200.40 . . . . . .S30100 301 0.15 2.

25、00 0.045 0.030 1.00 16.018.0 6.08.0 . . . 0.10 . . . . . .S30103 301LG0.03 2.00 0.045 0.030 1.00 16.018.0 6.08.0 . . . 0.20 . . . . . .S30153 301LNG0.03 2.00 0.045 0.030 1.00 16.018.0 6.08.0 . . . 0.070.20 . . . . . .S30200 302 0.15 2.00 0.045 0.030 0.75 17.019.0 8.010.0 . . . 0.10 . . . . . .S30400

26、 304 0.07 2.00 0.045 0.030 0.75 17.519.5 8.010.5 . . . 0.10 . . . . . .S30403 304L 0.030 2.00 0.045 0.030 0.75 17.519.5 8.012.0 . . . 0.10 . . . . . .S30409 304H 0.040.10 2.00 0.045 0.030 0.75 18.020.0 8.010.5 . . . . . . . . . . . .S30415 . . . 0.040.06 0.80 0.045 0.030 1.002.00 18.019.0 9.010.0 .

27、. . 0.120.18 . . . Ce 0.030.08S30451 304N 0.08 2.00 0.045 0.030 0.75 18.020.0 8.010.5 . . . 0.100.16 . . . . . .S30452 XM-21J0.08 2.00 0.045 0.030 0.75 18.020.0 8.010.5 . . . 0.160.30 . . . . . .S30453 304LN 0.030 2.00 0.045 0.030 0.75 18.020.0 8.012.0 . . . 0.100.16 . . . . . .S30500 305 0.12 2.00

28、0.045 0.030 0.75 17.019.0 10.513.0 . . . . . . . . . . . .S30530 . . . 0.08 2.00 0.045 0.030 0.502.50 17.020.5 8.511.5 0.751.50 . . . 0.753.5 . . .S30600 . . . 0.018 2.00 0.020 0.020 3.74.3 17.018.5 14.015.5 0.20 . . . 0.50 . . .S30601 . . . 0.015 0.500.80 0.030 0.013 5.05.6 17.018.0 17.018.0 0.20 0

29、.05 0.35 . . .S30615 . . . 0.160.24 2.00 0.030 0.030 3.24.0 17.019.5 13.516.0 . . . . . . . . . Al 0.801.50S30815 . . . 0.050.10 0.80 0.040 0.030 1.402.00 20.022.0 10.012.0 . . . 0.140.20 . . . Ce 0.030.08S30908 309S 0.08 2.00 0.045 0.030 0.75 22.024.0 12.015.0 . . . . . . . . . . . .S30909 309HG0.0

30、40.10 2.00 0.045 0.030 0.75 22.024.0 12.015.0 . . . . . . . . . . . .S30940 309CbG0.08 2.00 0.045 0.030 0.75 22.024.0 12.016.0 . . . . . . . . . Cb 103C min,1.10 maxA240/A240M09a3TABLE 1 ContinuedUNSDesignationBTypeCCarbonDManganese Phos-phorusSulfur Silicon Chromium Nickel Molybdenum Nitrogen Coppe

31、r OtherElementsE,FS30941 309HCbG0.040.10 2.00 0.045 0.030 0.75 22.024.0 12.016.0 . . . . . . . . . Cb 103C min,1.10 maxS31008 310S 0.08 2.00 0.045 0.030 1.50 24.026.0 19.022.0 . . . . . . . . . . . .S31009 310HG0.040.10 2.00 0.045 0.030 0.75 24.026.0 19.022.0 . . . . . . . . . . . .S31040 310CbG0.08

32、 2.00 0.045 0.030 1.50 24.026.0 19.022.0 . . . . . . . . . Cb 103C min,1.10 maxS31041 310HCbG0.040.10 2.00 0.045 0.030 0.75 24.026.0 19.022.0 . . . . . . . . . Cb 103C min,1.10 maxS31050 310 MoLNG0.020 2.00 0.030 0.010 0.50 24.026.0 20.523.5 1.602.60 0.090.15 . . . . . .S31060 . . . 0.050.10 1.00 0.

33、040 0.030 0.50 22.024.0 10.012.5 . . . 0.180.25 . . . Ce + La0.0250.070B 0.0010.010S31254 . . . 0.020 1.00 0.030 0.010 0.80 19.520.5 17.518.5 6.06.5 0.180.22 0.501.00 . . .S31266 . . . 0.030 2.04.0 0.035 0.020 1.00 23.025.0 21.024.0 5.26.2 0.350.60 1.002.50 W 1.502.50S31277 . . . 0.020 3.00 0.030 0.

34、010 0.50 20.523.0 26.028.0 6.58.0 0.300.40 0.501.50 . . .S31600 316 0.08 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.10 . . . . . .S31603 316L 0.030 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.10 . . . . . .S31609 316H 0.040.10 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 . . . . .

35、 . . . .S31635 316TiG0.08 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.10 . . . Ti 5 3 (C+N)min, 0.70 maxS31640 316CbG0.08 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.10 . . . Cb 10 3 Cmin, 1.10 maxS31651 316N 0.08 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.100.16 . . . . . .S31

36、653 316LN 0.030 2.00 0.045 0.030 0.75 16.018.0 10.014.0 2.003.00 0.100.16 . . . . . .S31700 317 0.08 2.00 0.045 0.030 0.75 18.020.0 11.015.0 3.04.0 0.10 . . . . . .S31703 317L 0.030 2.00 0.045 0.030 0.75 18.020.0 11.015.0 3.04.0 0.10 . . . . . .S31725 317LMG0.030 2.00 0.045 0.030 0.75 18.020.0 13.51

37、7.5 4.05.0 0.20 . . . . . .S31726 317LMNG0.030 2.00 0.045 0.030 0.75 17.020.0 13.517.5 4.05.0 0.100.20 . . . . . .S31727 . . . 0.030 1.00 0.030 0.030 1.00 17.519.0 14.516.5 3.84.5 0.150.21 2.84.0 . . .S31753 317LNG0.030 2.00 0.045 0.030 0.75 18.020.0 11.015.0 3.04.0 0.100.22 . . . . . .S35115 865 0.

38、030 1.00 0.045 0.015 0.501.50 23.025.0 19.022.0 1.502.50 0.200.30 . . . . . .S32050 . . . 0.030 1.50 0.035 0.020 1.00 22.024.0 20.023.0 6.06.8 0.210.32 0.40 . . .S32053 . . . 0.030 1.00 0.030 0.010 1.00 22.024.0 24.026.0 5.06.0 0.170.22 . . . . . .S32100 321 0.08 2.00 0.045 0.030 0.75 17.019.0 9.012

39、.0 . . . 0.10 . . . Ti 5 3 (C+N)min, 0.70 maxS32109 321H 0.040.10 2.00 0.045 0.030 0.75 17.019.0 9.012.0 . . . . . . . . . Ti 4 3 (C+N)min, 0.70 maxS32615 . . . 0.07 2.00 0.045 0.030 4.86.0 16.519.5 19.022.0 0.301.50 . . . 1.502.50 . . .S32654 . . . 0.020 2.04.0 0.030 0.005 0.50 24.025.0 21.023.0 7.

40、08.0 0.450.55 0.300.60 . . .S33228 . . . 0.040.08 1.00 0.020 0.015 0.30 26.028.0 31.033.0 . . . . . . . . . Ce 0.050.10Cb 0.61.0Al 0.025S33400 334G0.08 1.00 0.030 0.015 1.00 18.020.0 19.021.0 . . . . . . . . . Al 0.150.60Ti 0.150.60S34565 . . . 0.030 5.07.0 0.030 0.010 1.00 23.025.0 16.018.0 4.05.0

41、0.400.60 . . . Cb 0.10S34700 347 0.08 2.00 0.045 0.030 0.75 17.019.0 9.013.0 . . . . . . . . . Cb 10 3 C min,1.00 maxS34709 347H 0.040.10 2.00 0.045 0.030 0.75 17.019.0 9.013.0 . . . . . . . . . Cb 8 3 C min,1.00 maxS34800 348 0.08 2.00 0.045 0.030 0.75 17.019.0 9.013.0 . . . . . . . . . (Cb + Ta) 1

42、03Cmin, 1.00 maxTa 0.10Co 0.20A240/A240M09a4TABLE 1 ContinuedUNSDesignationBTypeCCarbonDManganese Phos-phorusSulfur Silicon Chromium Nickel Molybdenum Nitrogen Copper OtherElementsE,FS34809 348H 0.040.10 2.00 0.045 0.030 0.75 17.019.0 9.013.0 . . . . . . . . . (Cb + Ta) 83Cmin, 1.00 maxTa 0.10Co 0.2

43、0S35045 . . . 0.060.10 1.50 0.045 0.015 1.00 25.029.0 32.037.0 . . . . . . 0.75 Al 0.150.60Ti 0.150.60S35125 . . . 0.10 1.001.50 0.045 0.015 0.50 20.023.0 31.035.0 2.003.00 . . . . . . Cb 0.250.60S35135 . . . 0.08 1.00 0.045 0.015 0.601.00 20.025.0 30.038.0 4.04.8 . . . 0.75 Ti 0.401.00S35315 . . .

44、0.040.08 2.00 0.040 0.030 1.202.00 24.026.0 34.036.0 . . . 0.120.18 . . . Ce 0.030.10S38100 XM-15J0.08 2.00 0.030 0.030 1.502.50 17.019.0 17.518.5 . . . . . . . . . . . .S38815 . . . 0.030 2.00 0.040 0.020 5.56.5 13.015.0 13.017.0 0.751.50 . . . 0.751.50 Al 0.30Duplex (Austenitic-Ferritic)S31200 . .

45、 . 0.030 2.00 0.045 0.030 1.00 24.026.0 5.56.5 1.202.00 0.140.20 . . . . . .S31260 . . . 0.03 1.00 0.030 0.030 0.75 24.026.0 5.57.5 2.53.5 0.100.30 0.200.80 W 0.100.50S31803 . . . 0.030 2.00 0.030 0.020 1.00 21.023.0 4.56.5 2.53.5 0.080.20 . . . . . .S32001 . . . 0.030 4.06.0 0.040 0.030 1.00 19.521

46、.5 1.003.00 0.60 0.050.17 1.00 . . .S32003 . . . 0.030 2.00 0.030 0.020 1.00 19.522.5 3.04.0 1.502.00 0.140.20 . . . . . .S32101 . . . 0.040 4.06.0 0.040 0.030 1.00 21.022.0 1.351.70 0.100.80 0.200.25 0.100.80 . . .S32202 . . . 0.030 2.00 0.040 0.010 1.00 21.524.0 1.002.80 0.45 0.180.26 . . . . . .S

47、32205 2205G0.030 2.00 0.030 0.020 1.00 22.023.0 4.56.5 3.03.5 0.140.20 . . . . . .S32304 2304G0.030 2.50 0.040 0.030 1.00 21.524.5 3.05.5 0.050.60 0.050.20 0.050.60S32506 . . . 0.030 1.00 0.040 0.015 0.90 24.026.0 5.57.2 3.03.5 0.080.20 . . . W 0.050.30S32520 . . . 0.030 1.50 0.035 0.020 0.80 24.026

48、.0 5.58.0 3.04.0 0.200.35 0.502.00 . . .S32550 255G0.04 1.50 0.040 0.030 1.00 24.027.0 4.56.5 2.93.9 0.100.25 1.502.50 . . .S32750 2507G0.030 1.20 0.035 0.020 0.80 24.026.0 6.08.0 3.05.0 0.240.32 0.50 . . .S32760K. . . 0.030 1.00 0.030 0.010 1.00 24.026.0 6.08.0 3.04.0 0.200.30 0.501.00 W 0.501.00S32900 329 0.08 1.00 0.040 0.030 0.75 23.028.0 2.05.00 1.002.00 . . . . . . . . .S32906 . . . 0.030 0.801.50 0.030 0.030 0.80 28.030.0 5.87.5 1.502.60 0.300.40 0.80 . . .S32950 . .

下载提示：本站仅提供存储空间/不修改/不编辑

1.请仔细阅读文档，确保文档完整性，对于不预览、不比对内容而直接下载带来的问题本站不予受理。
2.下载的文档，不会出现我们的网址水印。
3、该文档所得收入（下载+内容+预览）归上传者、原创作者；如果您是本文档原作者，请点此认领！既往收益都归您。

同意并开始全文预览

文档包含非法信息？点此举报后获取现金奖励！

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

10000 积分 0人已下载

下载	加入VIP,交流精品资源

版权申诉 word格式文档无特别注明外均可编辑修改；预览文档经过压缩，下载后原文更清晰！ 立即下载

配套讲稿：: 如PPT文件的首页显示word图标，表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
特殊限制：: 部分文档作品中含有的国旗、国徽等图片，仅作为作品整体效果示例展示，禁止商用。设计者仅对作品中独创性部分享有著作权。
关键词：: ASTMA240A240M2009ASTANDARDSPECIFICATIONFORCHROMIUMANDCHROMIUMNICKELSTAINLESSSTEELPLATESHEETANDSTRIPFORPRESSUREVESSELSANDFORGENERALAPPLICATIONSPDF

麦多课文档分享所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。

关于本文

本文标题：ASTM A240 A240M-2009a Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate Sheet and Strip for Pressure Vessels and for General Applications.pdf
链接地址：http://www.mydoc123.com/p-457780.html