ASTM A1042 A1042M-2004 Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains《排污和排水用复合波纹钢管标准规范》.pdf

《ASTM A1042 A1042M-2004 Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains《排污和排水用复合波纹钢管标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM A1042 A1042M-2004 Standard Specification for Composite Corrugated Steel Pipe for Sewers and Drains《排污和排水用复合波纹钢管标准规范》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 1042/A 1042M 04Standard Specification forComposite Corrugated Steel Pipe for Sewers and Drains1This standard is issued under the fixed designation A 1042/A 1042M; the number immediately following the designation indicates theyear of original adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers composite corrugated steelpipe, intended for uses such as storm water drainage, sani

3、tarysewers, underdrains, construction of culverts, and similar uses.The composite material used in fabrication of the pipe consistsof a three-layer polymer protective coating on both sides of asteel sheet core. The three layers consist of an inner layer offusion-bonded epoxy on the steel surface, an

4、 intermediate layerof polyethylene adhesive, and an outer layer of high-densitypolyethylene.1.2 The three-layer polymer coating protects the base metalagainst corrosion or abrasion, or both. Severe environments arelikely to cause corrosion problems to accessory items such ascoupling band hardware un

5、less supplemental protection isprovided. Additional protection for composite steel pipe isavailable by use of coatings applied after fabrication of the pipeas described in Specification A 849.1.3 This specification does not include requirements forbedding, backfill, or the relationship between earth

6、 cover loadand sheet thickness of the pipe. Experience with drainageproducts has shown that successful performance depends uponthe proper selection of corrugation profile, sheet thickness, typeof bedding and backfill, controlled manufacture in the plant,and care in installation. The installation pro

7、cedure is describedin Practice A 798/A 798M.1.4 This specification is applicable to orders in eitherinch-pound units as A 1042, or in SI units as A 1042M.Inch-pound units and SI units are not necessarily equivalent. SIunits are shown in brackets in the text for clarity, but they arethe applicable va

8、lues when the material is ordered toA 1042M.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulat

9、ory requirements prior to use.2. Referenced Documents2.1 ASTM Standards:2A 153/A 153M Specification for Zinc Coating (Hot-Dip) onIron and Steel HardwareA 307 Specification for Carbon Steel Bolts and Studs,60 000 psi Tensile StrengthA 563 Specification for Carbon and Alloy Steel NutsA 563M Specificat

10、ion for Carbon and Alloy Steel NutsMetricA 568/A 568M Specification for Steel Sheet, Carbon, andHigh-Strength Low-Alloy, Hot-Rolled and Cold-Rolled,General Requirements forA 742/A 742M Specification for Steel Sheet, MetallicCoated, and Polymer Precoated for Corrugated Steel PipeA 796/A 796M Practice

11、 for Structural Design of Corru-gated Steel Pipe, Pipe-Arches, and Arches for Storm andSanitary Sewers and Other Buried ApplicationsA 798/A 798M Practice for Installing Factory-Made Corru-gated Steel Pipe for Sewers and Other ApplicationsA 849 Specification for Post-Applied Coatings, Pavings,and Lin

12、ings for Corrugated Steel Sewer and Drainage PipeA 902 Terminology Relating to Metallic Coated Steel Prod-uctsB 633 Specification for Electrodeposited Coatings of Zincon Iron and SteelB 695 Specification for Coatings of Zinc MechanicallyDeposited on Iron and SteelC 443 Specification for Joints for C

13、ircular Concrete Sewerand Culvert Pipe, Using Rubber GasketsD 1005 Test Methods for Measurement of Dry-Film Thick-ness of Organic Coatings Using MicrometersD 1056 Specification for Flexible Cellular Materials,Sponge or Expanded RubberE29 Practice for Using Significant Digits in Test Data toDetermine

14、 Conformance with Specifications1This specification is under the jurisdiction of ASTM Committee A05 onMetallic Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.17 on Corrugated Steel Pipe Specifications.Current edition approved Nov. 1, 2004. Published December 2004.

15、2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box

16、C700, West Conshohocken, PA 19428-2959, United States.F 568 Specification for Carbon and Alloy Steel ExternallyThreaded Metric Fasteners2.2 AASHTO Standard:T249M Test for Helical Lock Seam Corrugated Pipe32.3 ANSI/AWWA Standard:C213 Standard for Fusion-Bonded Epoxy Coating for theInterior and Exteri

17、or of Steel Water Pipelines43. Terminology3.1 General DefinitionsFor definitions of general termsused in this standard, refer to Terminology A 902.3.2 Definitions of Terms Specific to This Standard:3.2.1 fabricatorthe producer of the pipe.3.2.2 manufacturerthe producer of the sheet.3.2.3 purchaserth

18、e person or agency that purchases thefinished product.4. Classification4.1 The composite corrugated steel pipe covered by thisspecification is classified as follows:4.1.1 Type ICThis pipe shall have a full circular crosssection, with a single thickness of corrugated sheet, fabricatedwith helical cor

19、rugations.4.1.2 Type ICSThis pipe shall have a full circular crosssection, with an outer shell of corrugated sheet, fabricated withhelical corrugations and lock seams, and an inner liner ofhigh-density polyethylene.5. Ordering Information5.1 Orders for material to this specification shall include th

20、efollowing information as necessary, to adequately describe thedesired product.5.1.1 Name of material (composite corrugated steel pipe),5.1.2 ASTM designation and year of issue, as A 1042-XXfor inch-pound units or as A 1042M-XX for SI units,5.1.3 Type of pipe (4.1),5.1.4 Diameter of circular pipe (T

21、able 1),5.1.5 Length, either total length or length of each piece andnumber of pieces,5.1.6 Description of corrugations (7.2),5.1.7 Sheet thickness (8.1.2),5.1.8 Coupling bands, number, and type (9.1) if special typeis required,5.1.9 Gaskets for coupling bands, if required (9.5),5.1.10 Certification

22、, if required (14.1), and5.1.11 Special requirements.6. Materials and Manufacture6.1 Steel Sheet for PipeAll pipe fabricated under thisspecification shall be formed from polymer coated sheetconforming to Annex A1 of this specification.3Available from American Association of State Highway and Transpo

23、rtationOfficials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001.4Available from American Water Works Association, 6666 West Quincy Ave.,Denver, CO 80235.TABLE 1 Pipe SizesNominal Inside Diameter Corrugation Sizesin. mm2-23 by12 in.68by13mm3by1in.75by25mm5by1in.125 by 25 mm12 by14

24、in.13 by 6.5mm916 by38 in.15by10mm6 150 x8 200 x10 250 x12 300 x x x15 375 x x x18 450 x x x21 500 x x x24 600 x x27 675 x x30 750 x x33 825 x x36 900 x x x42 1050 x x48 1200 x x54 1350 x x60 1500 x x66 x x72 1800 x x78 1950 x x84 2100 x x90 2250 x96 2400 x102 2550 x108 2700 x114 2850 x120 3000 x126

25、 3150 x132 3300 x138 3450 x144 3600 xNOTEAn “x” indicates standard composite corrugated profiles for each nominal diameter of pipe.A 1042/A 1042M 0426.2 Steel Sheet for Coupling BandsThe sheet used infabricating coupling bands shall be one of the following: thesame material as that specified for fab

26、rication of the pipefurnished under the order, with the same three-layer polymercoating; polymer precoated sheet conforming to SpecificationA 742/A 742M; stainless steel sheet of a grade selected by thefabricator.6.3 Steel Sheet for Connecting StrapsThe sheet used infabricating connecting straps for

27、 flange type couplings shall beone of the following: carbon steel sheet meeting the steelsubstrate requirements ofAnnexA1.3 or stainless steel sheet ofa grade selected by the fabricator.6.3.1 Except for stainless steel straps, connecting strapsshall be zinc coated after fabrication by one of the pro

28、cesses of6.4.1.6.4 Hardware for CouplingsBolts and nuts for couplingsshall conform to the following requirements:Bolts NutsFor A XXX pipe A 307 A 563, Grade AFor A XXXM pipe F 568, Class 4.6 A 563M, Class 56.4.1 Bolts, nuts, and other threaded items used with cou-plings shall be zinc coated by one o

29、f the following processes:hot-dip process as provided in SpecificationA 153; electroplat-ing process as provided in Specification B 633, Class Fe/Zn 8;or mechanical process as provided in Specification B 695,Class 8. Other hardware items used with coupling bands shallbe zinc coated by one of the fol

30、lowing processes: hot-dipprocess as provided in Specification A 153; electroplatingprocess as provided in Specification B 633, Class Fe/Zn 25; ormechanical process as provided in Specification B 695, Class25.6.4.2 As an alternative to the materials in 6.4 and coatingprocesses in 6.4.1, stainless ste

31、el bolts and nuts of a gradeselected by the fabricator are permitted to be used.6.5 GasketsIf gaskets are used in couplings, they shall bea band of expanded rubber that meets the requirements ofSpecification D 1056 for the “RE” closed cell grades, O-ringsmeeting the requirements of Specification C 4

32、43, or othermaterial approved by the purchaser.7. Fabrication7.1 General RequirementsPipe shall be fabricated in fullcircular cross section.7.1.1 Type IC pipe shall be fabricated with helical corruga-tions and a continuous lock seam extending helically from endto end of each length of pipe.7.1.2 Typ

33、e ICS pipe shall be fabricated with helical corru-gations and a continuous helical lock seam extending from endto end of each length of pipe, and with a smooth high-densitypolyethylene liner thermally bonded to the pipe polymercoating at each interior corrugation crest over the length of thepipe. Th

34、e minimum thickness of the liner shall be 0.020 in.0.50 mm.7.2 CorrugationsThe corrugations shall be helical asprovided in 7.1.1. The direction of the crests and valleys of thehelical corrugations shall not be less than 60 from the axis ofthe pipe for pipe diameters larger than 21 in. 525 mm, and no

35、tless than 45 from the axis for pipe diameters of 21 in. 525mm and smaller.7.2.1 The corrugations shall form smooth continuouscurves, or curves and tangents. The dimensions of the corru-gations shall be in accordance with Table 2 for the nominal sizeindicated on the order. If the depth measurement o

36、f one ormore corrugations is less than the specified minimum depth inTable 2, the depth of all the corrugations between adjacentseams shall be measured and the values in Table 3 forminimum average depth and minimum corrugation depth shallapply.NOTE 1Inspection frequently consists of measurement of t

37、he depth ofone or a few corrugations. If such measurement indicates insufficientdepth, application of the requirements in Table 3 provides for acceptancewhere greater depth of some corrugations compensates for lack of depthof others. These measurements would normally be made at one locationbetween t

38、he seams on a length of pipe.NOTE 2The nominal dimensions and properties for pipe wall corru-gations are given in Practice A 796/A 796M.7.3 Helical Lock SeamsThe lock seam shall be formed inthe pipe wall near mid-depth.TABLE 2 Corrugation RequirementsNominalSizeMaximumPitchAMinimumDepthBNominal Insi

39、deRadiusCMinimum InsideRadiusinches2-23 by12 2-78 0.481116 0.503by1 3-14 0.95916 0.505by1 5-516 0.95 1.57 1.412 by14916 0.2418D0.09916 by38 5/8 0.4018 0.09millimetres68 by 13 73 12 17 1275 by 25 83 24 14 12125 by 25 135 24 40 3613 by 6.5 14 6.1 3.2D2.315 by 10 16 10.2 3.2 2.3APitch is measured from

40、crest to crest of corrugations, at 90 to the direction of the corrugations.BDepth is measured as the vertical distance from a straightedge resting on the corrugation crests parallel to the axis of the pipe to the bottom of the intervening valley.If the depth measurement of one or more corrugations i

41、s less than the value indicated herein, the depth of all corrugations between the seams shall be measured, andthe requirements of Table 3 shall be applied (see 7.2.1).CMinimum inside radius requirement does not apply to a corrugation containing a lock seam. The term “outside” refers to the outside s

42、urface of the pipe.DAverage of nominal inside radius (0.162 in.) 4.1 mm of outer corrugations and nominal inside radius (0.094 in.) 2.4 mm of inner corrugations.A 1042/A 1042M 0437.3.1 The edges of the sheets within the cross section of thelock seam shall lap as follows, but with an occasional toler

43、anceof 10 % of lap width allowable. For the 2-23 by12 in. 68 by13 mm, 3 by 1 in. 75 by 25 mm, or 5 by 1 125 by 25 mmcorrugations, the lap shall be at least516 in. 7.9 mm. For the12 by14 in. 13 by 6.5 mm and916 by38 in. 15 by 10 mmcorrugations, the lap shall be at least 0.125 in. 3.2 mm.7.3.2 The lap

44、ped surfaces shall be in tight contact. Theprofile of the sheet shall include a retaining offset adjacent tothe 180 fold (as described in AASHTO T249) of one sheetthickness on one side of the lock seam, or one-half sheetthickness on both sides of the lock seam, at the fabricatorsoption. There shall

45、be no visible cracks in the metal, loss ofmetal-to-metal contact, or excessive angularity on the interiorof the 180 fold of metal at the completion of forming the lockseam. Damage to the polymer coating is subject to repair inconformance with Section 11.7.3.3 Specimens cut from production pipe norma

46、l to andacross the lock seam shall develop the tensile strength listed inTable 4, when tested according to AASHTO T249M.7.4 End FinishIf flange type couplings or bands withannular corrugations are to be provided, the pipe ends shall beembedded in a high-density polyethylene flange with dimen-sions a

47、s specified in Table 5. If bell and spigot type couplingsare provided, the pipe ends shall be embedded in end deviceswith dimensions suitable for providing mating surfaces. Suchend devices for bell and spigot couplings shall be of high-density polyethylene, polyvinyl chloride, or other suitablepolym

48、er material.8. Pipe Requirements8.1 Types IC and ICS Pipe:8.1.1 Pipe DimensionsThe nominal diameter of the pipeshall be as stated in the order, selected from the sizes listed inTable 1. The size of corrugations that are standard for each sizeof pipe are also shown in Table 1. The average inside diam

49、eterof circular pipe, shall not vary more than 1 % or12 in. 13mm, whichever is greater, from the nominal diameter whenmeasured on the inside crest of the corrugations.8.1.2 Sheet ThicknessSheet thickness shall be as specifiedby the purchaser from the specified sheet thicknesses listed inTable A1.1, Annex A1.9. Coupling Systems9.1 Types of Coupling SystemsField joints for each typeof composite corrugated steel pipe shall maintain pipe align-ment during construction and prevent infiltra