ASD-STAN PREN 4830-003-2014 Aerospace series Connectors optical rectangular modular operating temperature 125 for EN 4639-10X contacts Part 003 Module Product standard (Edition P 1.pdf

《ASD-STAN PREN 4830-003-2014 Aerospace series Connectors optical rectangular modular operating temperature 125 for EN 4639-10X contacts Part 003 Module Product standard (Edition P 1.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 4830-003-2014 Aerospace series Connectors optical rectangular modular operating temperature 125 for EN 4639-10X contacts Part 003 Module Product standard (Edition P 1.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM prEN 4830-003 Edition P 1 March 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONRue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION A

2、erospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4639-10X contacts Part 003: Module Product standard Srie arospatiale Connecteurs optiques rectangulaires, modulaires, temprature dutilisation 125 C, pour contacts EN 4639-10X Partie 003 : Module Norme de p

3、roduit Luft- und Raumfahrt Optischer Rechtecksteckverbinder, modular, Betriebstemperatur 125 C, fr EN 4639-10X-Kontakte Teil 003: Module Produknorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe -

4、 Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that inte

5、rchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and tran

6、sformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 1stMarch 2014 Comments should be

7、sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2014 by ASD-STAN prEN 4830-003:2014 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 Terms and definitions . 3 4 Required characteristics . 3 5 Designation 8 6 Marking . 8 7 Technical spec

8、ification . 8 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN

9、4830-003:2014 (E) 3 1 Scope This standard defines the material used in the manufacturing of EN 4830 optical modules. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only

10、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products EN 4165-003, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuo

11、us Part 003: Modules series 2 and series 3 Product standard EN 4830-001, Aerospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4639-10X contacts Part 001: Technical specification 1)EN 4830-002, Aerospace series Connectors, optical, rectangular, modular, oper

12、ating temperature 125 C, for EN 4639-10X contacts Part 002: Specification of performance 1)EN 4830-004, Aerospace series Connectors, optical, rectangular, modular, operating temperature 125 C, for EN 4639-10X contacts Part 004: Extraction tool Product standard 1)IEC 61300-3-33, Fibre optic interconn

13、ecting devices and passive components Basic test and measurement procedures Part 3-33: Examinations and measurements Ferrule withdrawal force 2)MIL-I-81969/14-03, Installing and removal tools, connector electrical contact, type III, class 2, composition B3)TR 4684, Aerospace series Electrical and Op

14、tical technology and component definitions 4)3 Terms and definitions For the purposes of this document, the terms and definitions given in TR 4684 apply. 4 Required characteristics 4.1 Dimensions and masses 4.2 Male module interface dimensions Series 2 and 3 See Figure 1. 1) Published as ASD-STAN Pr

15、estandard at the date of publication of this standard. http:/www.asd-stan.org/2) Published by: IEC International International Electrotechnical Commission http:/www.iec.ch/. 3) Published by; DoD National (US) Mil. Department of Defense http:/www.defenselink.mil/. 4) In preparation at the date of pub

16、lication of this standard prEN 4830-003:2014 (E) 4 Dimensions and tolerances are in millimetres. Key 1 Guiding pin 2 Coding location (see EN 4165-003) 3 Optional design for sealed version 4 Center coupling screw/device as per -001 5 Termini orientation key 6 Interfacial seal NOTE 1 Mass: 5,10 g max.

17、 NOTE 2 Others dimensions, see EN 4165-003. Figure 1 prEN 4830-003:2014 (E) 5 4.3 Female module interface dimensions Series 2 See Figure 2. Dimensions and tolerances are in millimetres. Key 1 Guiding pin 2 Coding location (see EN 4165-003) 3 Optional design for sealed version 4 Center coupling screw

18、/device as per -001 5 Termini orientation key 6 Interfacial seal 7 Sleeve holder NOTE1 Mass: 7,50 g max. NOTE 2 Others dimensions, see EN 4165-003. Figure 2 prEN 4830-003:2014 (E) 6 4.4 Female module interface dimensions Series 3 See Figure 3. Dimensions and tolerances are in millimetres. Key 1 Guid

19、ing pin 2 Coding location (see EN 4165-003) 3 Optional design for sealed version 4 Centring fixing 5 Termini orientation key 6 Interfacial seal 7 Sleeve holder NOTE 1 Mass: 9,00 g max. NOTE 2 Others dimensions, see EN 4165-003. Figure 3 prEN 4830-003:2014 (E) 7 4.5 Sleeve holder See Figure 4. Dimens

20、ions and tolerances are in millimetres. Key 1 Alignment sleeve 2 6 cavities 3 3 mm hex. Captive screw 4 Module limit stop 5 Floating movement NOTE Mass: 1,6 g max. Figure 4 4.6 Material and surface treatment See EN 4830-002. 4.7 Optical, mechanical and climatic characteristics See EN 4830-001. 4.8 T

21、ool See EN 4830-004. prEN 4830-003:2014 (E) 8 5 Designation EXAMPLE Description block OPTICAL MODULES Identification block EN4830 A 06EL X X X Number of the basic standard Module series Series 2 = A Series 3 = B Module arrangement 06 = 6 cavities EL = termini according EN 4639-10X Peripheral sealing

22、 Unsealed = 1 Sealed = 2 Polarization (see EN 4165-003) N = Normal, or A, B, C, D Modules type Male = P Female = S 6 Marking The marking shall include the identification defined in Clause 5, the date of manufacture (year, week) and the name or trade mark of the manufacturer or conform to standard EN 2424, code P, if required. 7 Technical specification See EN 4830-001.