ARMY MIL-R-53002 (2)-1985 RETROFIT KIT ROLLER MINE CLEARING TRACK-WIDTH TANK-MOUNTED《滚筒式排雷加装套件 坦克安装的磁迹宽度》.pdf

《ARMY MIL-R-53002 (2)-1985 RETROFIT KIT ROLLER MINE CLEARING TRACK-WIDTH TANK-MOUNTED《滚筒式排雷加装套件 坦克安装的磁迹宽度》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-R-53002 (2)-1985 RETROFIT KIT ROLLER MINE CLEARING TRACK-WIDTH TANK-MOUNTED《滚筒式排雷加装套件 坦克安装的磁迹宽度》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-53002 (2) LO 9999906 0334444 L -1 -53 - 37- 63 I ML-R-53002 (ME) AMENDMENT 2 4 June 1985 SUPERSEDING AMENDMENT 1 6 July 1983 MILITARY SPECIFICATION RETROFIT KIT, ROLLER, MINE CLEARING: TRACK-WIDTH, TANK-MOUNTED This amendment forms a part of Military Specification MIL-R-53002(ME), dated 16 Feb

2、ruary 1982, and is approved for use by the USA Belvoir Research and Development Center, Department of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 * 2.1.1, under SPECIFICATIONS, MILITARY delete: “MIL-B-117 - Bag, Sleeve and Tubing - Interior

3、Packaging.“ PAGE 2 * Under STANDARDS, MILITARY delete: “MIL-STD-118 8 - Commercial Packaging of Supplies and Equipment. II B * 2.2, Add: “AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) .- ASTM D 3951 - Standard Practices for Commercial Packaging. (Application for copies should be addressed to the

4、 American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.)“ PAGE 4 3.9.2, line 8, after “used.“, add the following sentences: “Welds shall not For welds 318 . exceed the next 1/16 inch larger size for welds up to 318 inch. inch and larger, the size shall not exceed the n

5、ext 118 inch larger size. shall not be undersize.“ Welds PAGE 8 * Delete 4.7.1 and 4.7.1.1 in their entirety and substitute: II 4.7.1 First article inspection of packaging. FSC 1095 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M IL-R-5 300 2 (ME A

6、MENDMENT 2 4.7.1.1 Examination. The first article packaging shall be examined for the defects specified in table III. Presence of one or more defects shall be cause for rejection.“ PAGE 9 * 4.7.2.3, table III, delete defect number 114 * 5.1, delete the heading “Preproduction pack“ packaging“. in its

7、 entirety. and substitute “First article * 5.1, lines 1, 6, 7, 8 and 10, delete “preproduction“ and substitute “first art i c le“ . * Line 2, delete “and testing.“ without substitution. * Line 5, delete “and test.“ without substitution and delete “those“ and subs t i tut e “a c I . * 5.3, line 1, de

8、lete the period following “as specified“ and add “(see 6.21.“ PAGE 10 * Delete 5.3.2 in its entirety and substitute the following: “5.3.2 Commercial. A complete kit shall be packed in accordance with ASTM D 3951.“ * Delete 5.4 in its entirety without substitution. * Delete 5.5.2 in its entirety and

9、substitute the following: “5.5.2 Commercial. Marking for commercial packaging shall be in accordance with ASTM D 3951. the gross weight and cube.“ Additionally, each shipping container shall be.marked with * Add the following new paragraph: “6.5 First article pack. Any changes or deviations of produ

10、ction packs from the approved first article pack will be subject to the approval of the contracting officer. Approval of the first article pack will not relieve the contractor of his obligation to preserve, pack and mark the kits in accordance with this specification.“ PAGE 13 * Delete number 7 in i

11、ts entirety. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-R-53002 (2) LO W 777770b 0334446 5 If MIX-R-53002 (ME 1 MNDXENT 2 PAGE 17 * Delete number 14 in its entirety. The margins of this amendment are marked with an asterisk to indicate wh

12、ere changes (additions, modifications, corrections, deletions) from the previous amendment were made. This was done as a convenience only and the Government assumes. no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of

13、 this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment. Custodian: Amy - ME Review activity: Army - AT Preparing activity: Amy - ME Pr0.j e c t 1 O 9 5-Al 7 4 f7U.S. GOVERNMENT PRINTING OFFICE 1985 - 606-038/22741 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-