ARMY MIL-D-51559-1991 DECONTAMINATING APPARATUS PORTABLE 14 LITER M13 (PRACTICE)《M13(练习)14升便携式去污器》.pdf

《ARMY MIL-D-51559-1991 DECONTAMINATING APPARATUS PORTABLE 14 LITER M13 (PRACTICE)《M13(练习)14升便携式去污器》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-D-51559-1991 DECONTAMINATING APPARATUS PORTABLE 14 LITER M13 (PRACTICE)《M13(练习)14升便携式去污器》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、- s. . o DECO MIL-D-5L559 42 = 9999906 0500577 7 m MIL-D-51559 (EA) 10 October 1991 MILITARY SPECIFICATION iTAMINATING APPARATUS: PORTABLE, 14 LITER, M13 (PRACTICE) This specification is approved for use by the US. Army Chemical Research, Development and Engineering Center, Department of the Army, a

2、nd is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of assembled practice decontaminating apparatus (see 6. i). 2. APPLICABLE DOCUMENTS 2.1 Government documents. O 2. i. 1 Specifications, standards, and handbook

3、s. The following specifications, stan- dards, and handbooks form a partof this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Depart- ment of Defense Index of Specifications and Standards (DODISS) and supplement

4、 thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL PPP-B-585 - Boxes, Wood, Wirebound PPP-B-636 - Boxes, Shipping Fiberboard Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Co

5、mmander, U.S. Army Chemical Research, Development and Engineering Center, ATTN: SMCCR-PET-S, Aberdeen Proving Ground, MD 2 10 10-5423 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this documerit or by letter. AMSC N/A FSC 4230 Approv

6、ed for public release; distribution is unlimited. DISTRIBUTION STATEMENT A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-5L559 Y2 = 9999906 0500578 9 = I MIL-D-5 1 5 59 (EA) PPP-F-320 - Fiberboard: Corrugated and Solid Sheet Stock (Container

7、 Grade) and Cut Shapes. STANDARDS MILITARY MIL-STD-1168 - Ammunition Lot Numbering (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 1

8、1-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicita- tion. U.S. ARMY CHEMICAL RE

9、SEARCH, DEVELOPMENT AND ENGINEERING CENTER DRAWINGS 5-5 1-608 - Decontaminating Apparatus: Portable, 14 Liter, Mi 3 (Practice) 5-51-609 - Packaging and Marking (Practice) 5-51-610 - Palletization and Marking (Practice) 5-51-611 - Packing and Marking (Practice) (Copies are available from Commander, U

10、.S. Army Information Systems Command, ATIN: ASQNC-ARI-IOT, Rock Island, IL 61299-7210.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes app

11、licable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials cited on Drawing 5-51-608 and on the subsidiary drawings shall conform to the specifications and drawings listed thereon. 3.2 Components. All components of the practice apparatus

12、shall conform to the specifi- cations and drawings listed on Drawing 5-51-608 and subsidiary drawings. 3.3 Manufacture and assembly. The practice apparatus shall be manufactured and assembled in accordance with Drawing 5-5 1-608. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted

13、 without license from IHS-,-,-MIL-D-51559 Y2 m 999790b 0500579 O = MIL-D-5 15 59 (EA) 3.4 Spray characteristics. Using the Government-furnished DS2-filled fluid container (see 3.6) in lieu of the empty plastic container (Drawing 5-51-598), at room conditions the apparatus shall be capable of being p

14、rimed with no more than 10 strokes of the pump piston. With the wand held horizontally a minimum of 4 feet above the outlet of the DS2-filled fluid container, spray shall be projected a horizontal distance of at least 3 feet and no leakage shall occur when the pump is activated and tested in accorda

15、nce with 4.4.6.1. 3.5 First article. Unless otherwise specified in the contract, a sample of practice appa- ratus shall be subjected to the first article inspection specified in 4.3 prior to the start of regular production and whenever there is a lapse in production for a period in excess of 90 days

16、 or whenever a change occurs in manufacturing process, material, drawings, specifica- tions, or source of supply as to significantly affect product uniformity as determined by the Government. 3.6 Government-furnished equipment (see 6.5). The Government will furnish DS2-filled fluid containers (Drawi

17、ng 5-51-575) to the contractor to conduct the spray char- acteristics test (4.4.6.1). 3.7 Workmanship. The practice apparatus shall be free from cracks, dents, sharp edges, unpainted surfaces, rust, and foreign matter such as dirt, grease, and oily or viscous materi- als. O 4. QUALITY ASSURANCE PROV

18、ISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (ex- aminations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, th

19、e contractor may use his own or any other facilities suitable for the per- formance of the inspection requirements specified herein, unless disapproved by the Govern- ment. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are

20、deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or qual

21、ity program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all require- ments of the contract. Sampling inspection, as part of man

22、ufacturing operations, is an ac- ceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 3 Provided by IHSNot for ResaleNo reproduc

23、tion or networking permitted without license from IHS-,-,-MIL-D-SL559 42 m 9999906 O500580 7 4.1.2 Contractor assurance of compliance. The contractors quality program or de- tailed inspection system shall provide assurance of compliance of all characteristics with the applicable drawing, special pac

24、kaging instruction, and specification requirements using, as a minimum, the conformance criteria specified herein. 4.1.3 Alternative inspection provisions. Alternative inspection procedures, methods, or equipment, such as statistical process control, tool control, and other types of sampling procedu

25、res may be used by the contractor when they provide, as a minimum, the level of quality assurance required by the inspection provisions specified herein. Prior to applying such alternative procedures, methods, or equipment, the contractor shall describe them in a written proposal submitted to the Go

26、vernment for evaluation and approval. (See 6.3.) When required, the contractor shall demonstrate that the effectiveness of each proposed alternative is equal to or better than the quality assurance provisions specified herein. In cases of dispute as to whether the contractors proposed alternative pr

27、ovides equal quality assurance, the provisions of this specification shall apply. All approved alternative inspec- tion provisions shall be specifically incorporated into the contractors quality program or detailed inspection system, as applicable. 4.2 Classification of inspections. The inspection r

28、equirements specified herein are clas- sified as follows: (a) First article inspection (see 4.3) (b) Quality conformance inspection (see 4.4) 4.3 First article inspection. 4.3.1 Inspections to be performed. As determined by the Government, the first article sample items shall be examined and tested

29、in accordance with this specification using either the first article procedures in 4.3.3 or other first article procedures which will be provided by the Government. As determined by the Government, the sample first article items may be subjected to any or all of the examinations and tests specified

30、in this specification and be inspected for compliance with any or all of the requirements of the applicable drawings and special packaging instructions. 4.3.2 Sample. The first article sample shall consist of 100 practice apparatus manufac- tured and packaged using the same methods, materials, equip

31、ment, and processes as will be used during regular production. The first article sample shall be submitted for inspection and approval in accordance with the terms of the contract. 4.3.3 Inspection procedure (see 6.4). 4.3.3.1 For examination and test. Twenty practice apparatus shall be taken at ran

32、dom from the first article sample and subjected to the spray characteristics test specified in 4.4.6.1. Twenty decontaminating apparatus and the packaging thereof shall be taken at 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- I MIL-D-5L559 L(2

33、7999906 0500581 7 = MIL-D-5 15 59 (EA) 0 random from the first article sample and examined for all of the remaining characteristics in the classification of characteristics using the inspection methods specified therein. 4.3.4 Acceptance criteria. If any first article sample item fails to comply wit

34、h any of the applicable requirements, the first article sample shall be rejected. The Government re- serves the right to terminate inspection upon any failure to comply with any of the require- ments. The contractor shall obtain written approval from the contracting activity prior to proceeding with

35、 regular production. 4.4 Quality conformance inspection. 4.4.1 Lotting. A lot of practice apparatus shall consist of those like items produced at the same place utilizing the same batches of materials, lot of components, process runs, fabrication techniques, assembly methods, tools, equipment and fa

36、cilities but shall not ex- ceed one months production. Each lot shall be controlled and identified in accordance with MIL-STD-1168. No more than one interfix lot number of filled fluid containers shall be contained in any one lot of practice apparatus. 4.4.2 Sampling. Sampling shall be conducted in

37、accordance with the classification of characteristics in 4.4.5 and, when specified, table I. Samples shall be selected at random. 4.4.3 Inspection procedure (see 6.4). Every item in the lot shall be inspected for criti- cal characteristics. The lot represented shall be rejected when nonconformance t

38、o a critical characteristic is found. Sample items and, when applicable, the packaging thereof shall be examined and tested in accordance with the classification of characteristics in 4.4.5. Failure of any sample item to conform to any characteristic in the classification of characteristics based on

39、 the sampling and acceptance criteria specified therein shall be cause for rejection of the lot represented. 4.4.4 Inspection Characteristics. Critical characteristics are characteristics whose non- conformance to specified requirements is likely to result in hazardous or unsafe conditions for indiv

40、iduals using, maintaining, or depending upon the product or whose nonconformance to specified requirements is likely to prevent performance of the tactical function of a major end item. Major characteristics are characteristics whose nonconformance to specified re- quirements is likely to result in

41、failure or to reduce materially the usability of the item for its intended purpose, Minor characteristics are characteristics whose nonconformance to specified requirements is not likely to reduce materially the operation or usability of the item for its intended purpose. 5 Provided by IHSNot for Re

42、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-5L559 42 999990b 0500582 O Lot size 2 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1200 1201 to 3200 3201 to 10000 10001 to 35000 35001 to 15000 150001 to 500000 500001 and over MIL-D-5 1

43、 5 5 9 (EA) TABLE I. Sampling I * * * * * * * * * 1250 1250 1250 1250 1250 1250 II * * * * * * * 315 315 315 315 315 490 715 715 Inspection levels and sample sizes III * * * * * 125 125 125 125 125 192 294 294 345 435 IV * * * * 50 50 50 50 75 116 116 135 170 200 244 - V * * * 32 32 32 32 48 73 73 8

44、6 108 123 156 189 VI * * 20 20 20 20 20 47 47 53 68 77 96 119 143 - VII * 13 13 13 13 13 20 29 34 42 50 60 74 90 102 VIII * 8 8 .8 8 12 19 21 27 35 38 46 56 64 64 Ix 5 5 5 5 7 11 13 16 19 23 29 35 40 40 40 X 3 3 3 5 6 7 10 11 15 18 22 29 29 29 29 XI 2 2 3 5 5 6 7 9 11 13 15 15 15 15 15 *Indicates on

45、e hundred percent inspection. If sample size exceeds lot size, perform one hundred percent inspection. Accept the lot represented on zero nonconforming characteristics and reject the lot represented on one or more nonconforming characteristics for all inspection levels. 4.4.5 Classification of chara

46、cteristics. Quality conformance examinations and tests shall be as specified in the following classification of characteristics paragraphs. When specified herein, accept on O and reject on 1 attributes sampling inspection shall be per- formed on the designated characteristics using the stated levels

47、 in table I for selection of sample sizes. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-51559 42 W 9999906 0500583 2 Critical Major 101 102 103 104 105 PARAGRAPH 4.4.5(a) Minor 201 202 MIL-D-5 1 5 59 (EA) CLASSIFICATION OF CHARACTERISTICS

48、TITLE DRAWING NUMBER Decontaminating apparatus: portable, 14 liter, NEXT HIGHER ASSY 5-51-608 SHEET OF M13 Wractice) CHARACTERISTIC None defined Width Height Length Spray characteristics Specified components correctly assembled Labels evident and correctly assembled Workmanship NOTES: CE - Commercia

49、l inspection equipment VI - Visual inspection SAMPLING AND ACCEPTANCE CRITERIA Table I, Level VII Table I, Level VIT Table I, Level VI: 4; Acc O, Rej 1 Table I, Level VII Table I, Level IX Table I, Level VII IEQUIREMEN PARAGRAPH 3.2 3.2 3.2 3.4 3.2 and 3.2 3.2 3.7 INSPECTION METHOD CE CE CE 4.4.6.1 VI VI VI 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PARAGRAPH 4.4.5 (b) CATEGORY