ARMY MIL-C-48633-1987 CONTAINER AMMUNITION FIBERBOARD《纤维板制弹药箱》.pdf

《ARMY MIL-C-48633-1987 CONTAINER AMMUNITION FIBERBOARD《纤维板制弹药箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-48633-1987 CONTAINER AMMUNITION FIBERBOARD《纤维板制弹药箱》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-C-Yb33 33 I 99979Ob 0322630 9 = S-Q 3 u o LI rp O a k aJ a n M -Co ? n O 10 F E L O LL n v n Q O v) W u a- w- e - n L3 c3 n W LL P n O h Ln - E L O LL U r a 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-48633 13 W 7777906 0322615 MIL-

2、C-48633 (AR) 4.4 Quality conformance inspection. 4.4.1 Inspection lot formation. Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination. See MIL-A-48078. Unless otherwise specified in the Classification of Defects and Test Tables, sampling plans for major an

3、d minor defects shall be in accordance with MIL-STD-105. Unless otherwise specified, all inspections shall be performed at ambient temperature conditions (see 6.6). 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-tlIL-C-L1633 33 m 9999906 O322636 T

4、 m z O E u 4 pi ul z H H c c TI ai c. -4 ICI ai TI ai c O z a -4 c I) E m E 2 8 8 3 O a 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-48633 33 h 0322637 3 m MIL-C-48633 (AR) 4.4.3 Testing. Testing is described in the First article and Quali

5、ty Conformance Inspection tables. 4.4.4 Inspection equipment. The inspection equipment required to perform the inspections and tests prescribed in this specification is identified in the “Paragraph Reference/Inspection Method“ column in the tables starting with 4.4.2.1, and the test method paragraph

6、 (see 4.5). The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48078 and 6.3 herein. 4.5 Methods of inspection. 4.5.1 Free fall droE. After temperature conditioning for four (4) hours minimum, six (6) container a

7、ssemblies, two (2) each at the temperatures specified in 3.3, with five (5) inert mines installed in each, shall be dropped freely from the specified height on the top (closure end), one side, 450 to one corner of the top, 450 diagonally to the opposite corner of the base and on the bottom (a total

8、of five drops for each container assembly). The simulated mines shall measure 4.75 - .O25 in. diameter by 2.60 - .O25 in. high (right circular cylinder), and weigh 4 +1/4 pounds. Observation shall be made for compliance with the-requirement. 5. PACKAGING 5.1 Preservation and packaging 5.1.1 Commerci

9、al. Unless otherwise specified by the procuring activity, the preservation -and packaging shall be in accordance with ASTM-D-3951 except that the- unit package must contain eight (8) fiberboard container assemblies. 5.2 - Packing and marking. 5.2.1 Commercial. Unless otherwise specified by the procu

10、ring activity, all packing and marking shall be in accordance with ASTM-D-3951. 5.3 Shipping. When containers from more than one lot are shipped as a carload, each lot shall be kept separate and the division between lot clearly indicated to prevent mixing of the lots in transit. 6. NOTES 6.1 Intende

11、d use. The Fiberboard Ammunition Container is intended for use as the interior unit packaging for the M74, M75 and M79 mines; and as a means of handling the mines during field loading operations of the M128 Dispenser (GEMSS). 8 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

12、hout license from IHS-,-,-MIL-C-qb33 13 E 0b 0322bL 3 m MIL-6-48633 (AR) 6.2 Ordering data. See MIL-A-48078. 6.3 Tsign approvals. (See MIL-A-48078). Submit equipment designs as required to Commander, US Army AKmarrietIt Research, Development and Engineering Center, ATTN: AMSMC-QAT-%(Il), Dovear, New

13、 Jersey 07801-580. L 6.4 Drawings. Drawings listed in Section 2 of this specification under %he heading US Army Armament Research, Development and Engineering Center (ARDEC) may also include drawings prepared by, and identified as Edgewood Arsenal, Frankford Arsenal, Rock Island Arsenal, ARRADCOM, o

14、r Picatinny Arsenal drawings. Technical data originally prepared by these activities is now under the cognizance of ARDEC. 6.5 Distribution of ammunition data cards and test data. Distribution of datd following: Commander, US Army Armament Research, Development and Engineering Center, AMSMC-QAT-M(D)

15、, Dover, New Jersey 07801-5001. 6.6 Temperature. Ambient temperature shall be defined as 9 0091 OOF o - 6.7 1. Container Ammunition Fiberboard Free fall drop Custodian: Army-AR Preparing activity: Army-AR (Project 13 4 5-A3 39 ) 9 U.8. QOVERNNENT PRINTIHQ OFFICE: 1987 - 704-OS171213 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-