ARMY MIL-C-43352 D-1988 CLOTH NETTING NYLON TULLE TRICOT《丝网眼纱尼龙网织物》.pdf

《ARMY MIL-C-43352 D-1988 CLOTH NETTING NYLON TULLE TRICOT《丝网眼纱尼龙网织物》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-43352 D-1988 CLOTH NETTING NYLON TULLE TRICOT《丝网眼纱尼龙网织物》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、t I t O MIL-C-433 52D 30 June 1988 SUPERSEDING MIL-C-43352C 4 August 1982 MILITARY SPECIFICATION CLOTH, NETTING, NYLON, TULLE TRICOT This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This-document covers nylon tulle netting cloth

2、. 1.2 Classification. The cloth shall be of the following classes as specified (see 6.2). Class 1 - Untreated, OG-106 Class 2 - Resin treated, Dark Green 323 2. APPLICABLE DOCUMENTS * 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards,

3、 and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation.

4、 I i Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5014 by using the self-addressed Standardiza- tion Document

5、Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I I AMSC N/A FSC 8305 * DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. . THIS DOCUMENT CONTAINS 11 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

6、thout license from IHS-,-,- _I . MIL-C-43352D 83 7779906 0373236 3 SPECIFICATION FEDERAL PPP-P-1133 - Packaging of Synthetic Fiber Fabrics STANDARDS FEDERAL. FED-STD-191 - Textile Test Methods MILITARY MIL-STD-I05 - Samplkng Procedures nd Tables for Inspectian by At tributes * (Copies of specificati

7、ons, standards, and handbooks required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as irected by the eontractSng activity.) * 2.1.2 Other Gauernment cfacuments, drawings, and publications. The folIowing other Government documen

8、ts, drawings, and publications specification te the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of salicitation. form a part of this * FEDERAL TRADE COMMJESCION Rules and Regulations Under the Textile Fiber Products Identification Act (Copies

9、may he obtained from the Federal Trade Commission, Pennsylvania Avenue at Sixth Street, N.W., Washington, DC 20580.) * (Copies of drawings, publications, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting a

10、ctivity or as directed by the contracting activity.) * 2.2 Other puBications. The following documents form a part of this specification ta the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS speci

11、fied in the solicitation. issues of documents not listed in the DODISS shall be the issues of the nongovernment documents which are current on the date of solicitation. Unless otherwise specified, the Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M

12、IL-C-43352D 83 W 977770b 0373237 5 M = MIL-C-43352D . AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) Chromatic Transference Scale (Copies may be obtained from the American Association of Textile Chemists and Colorists, PO Box 12215, Research Triangle Park, NC 27709.) * (Nongovernment

13、 standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order of precedence. In the event of a conflict between the text of t

14、his specification and the references cited herein, the text of this specification shall take precedence. applicable laws and regulations unless a specific exemption has been obtained. Nothing in this specification, however, shall supersede 3. REQUIREMENTS * 3.1 First article. When specified in the c

15、ontract or purchase order, a sample shall be subjected to first article inspection (see 4.3, 6.2, and 6.3). * 3.2 Standard sample. The finished cloth shall match the standard sample for shade and appearance and shall be equal to or better than the standard sample with respect to all characteristics

16、for which the standard sample is referenced (see 6.4). O 3.3 Material. Materials shall be as specified herein (see 6.6). 3.3.1 Yarn. The yarn used in the manufacture of the cloth shall be mono- - filament, semi-dull, nylon. 3.4 Color. For class 1, the color of the finished cloth shall be Olive Green

17、 106 to match the standard sample (see 6.41, For class 2, the color of the treated and finished cloth shall be Dark Green 323 to match the standard sample (see 6.4). * 3.4.1 Matching. The color of the finished cloth shall match the standard sample when viewed under filtered tungsten lamps that appro

18、ximate artificial daylight and that have a correlated color temperature of 7500 2 200 K, with illumination of 100 + 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight at 2300 + 200 K. - 3 Provided by IHSNot for ResaleNo reproduction or networking permitted

19、 without license from IHS-,-,-MIL-C-43352D 3 W 9999906 0393238 7 W MIL-C-43352D ,y- - ._ * 3.4.2 Colorfastness. The finished cloth shall show colorfastness to laundering, bleaching, and perspiration equal to or better than the standard sample or equal to or better than a rating of “good“. show fastn

20、ess to crocking equal to or better than the standard sample or shall have an AATCC Chromatic Transference Scale rating of 3.5. Testing shall be as specified in 4.4.3. The finished cloth shall 3.5 Physical requirements. The finished cloth shall conform to the requirements in table I when tested as sp

21、ecified in 4.4.3. TABLE I. Physical requirements - _I - Class 2 -_-I- Characteristic Class 1 (min) (max) (min) (mad Weight per square yard, ounces O .4 0.6 O .3 0.7 Mesh repeats per inch; Wid th Leng th * Bursting strength, pounds 19 21 19 21 27 29 27 29 * 3.5.1 - Knit. 3.5.2 - Width. The width of t

22、he cloth shall be aa specified (see 6.2) and The cloth shall be a tricot or raschel knit fabric (see 6.5). shall be the minimum acceptable width inclusive of aelvages. 3.U Finish, The clasa 1 cloth shall be scoured. The clase E cloth shall be given a permanent resin finish and the character of the f

23、inished cloth shall be equal to that of the standard sample. 3.6.1 Heat tr-, The cloth shall be appropriately framed and heat set sa that the proper number of meshes per inch specified is maintained. 3.7 Length and put-up. Unless otherwise specified (see 6.21, the cloth shall be furnished in continu

24、ous lengths, each not less than 50 yards. shall be put up on full width rolls as specified in 5,l.l. No more than three pieces per rofi shall be permitted. The cloth 3.8 Fiber identification. Each roll of cloth shall be labeled or ticketed for fiber content in accordance with the Rules and Regulatio

25、ns Under the Textile Fiber Producta Identification Act. * 3.9 Workmanshie. The dyed and finished cloth shall conform to the quality of product established by this specification and the occurrence of defects shall not exceed the applicable acceptable quality levels, 4 Provided by IHSNot for ResaleNo

26、reproduction or networking permitted without license from IHS-,-,-MIL-C-LI3352D 83 7797706 0373239 9 MIL-C-43352D 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible or the performance of all i

27、nspection requirements as specified herein. in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any o

28、f the inspections set forth in this document where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise specified * 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The inspection s

29、et forth in this document shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the document shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for a

30、cceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of

31、 compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. * 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. b. Quality conformance inspection (see 4.4) First arti

32、cle inspection (see 4.3) * 4.3 First article inspection. When a first article is required (see 6.2), it shall he examined for the defects specified in 4.4.2 and tested for the characteristics specified in 4.4.3. pass any test shall be cause for rejection of the first article. The presence of any def

33、ect or failure to 4.4 Quality conformance inspection. Unless otherwise specified, sampling for inspection shall be performed in accordance with MIL-STD-105. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspectd in accordance with all the requirem

34、ents of referenced documents unless otherwise excluded, amended, modified or qualified in this document or applicable purchase document. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-C-43352D 83 W 777770b 0373240 5 W I MIL-C-43352D 4.4.2 En

35、d item visual examination. * 4.4.2.1 Yard-by-yard examination. The required yardage of each roll shall be examined for defects listed below. All defects clearly noticeable at normal inspection distance (3 feet) shall be counted regardless of their proximity to each other, except where two or more de

36、fects represent a single local condition of the cloth, in which case only one defect shall be counted. A continuous defect shall be counted as one defect for each warpwise yard or fraction thereof in which it occurs. The lot size shall be expressed in units of 1 yard. The sample unit shall be 1 line

37、ar yard. The inspection level shall be II and the acceptable quality level, (AQL), expressed in terms of defects per hundred units shall be 2.5. The number of rolls from which the yardage is to be selected shall be in accordance with table II. equally among the selected rolls, The sample yardage sha

38、ll be apportioned Defects Any cut, hole, tear, break, or mend Any thin area, or weak place Any loose or floating end Any coarse yarn more than three times the thickness of normal yarn Any broken or missing yarns Any edge folded, curled, torn, or broken Spot, stain or streak, more than 1 inch in comb

39、ined directions * 4.4.2.2 Overall examination. Each roll selected for yard-by-yard examination in accordance with table II shall be examined over its entire length for the defects listed below. Each defect shall be counted not more than once in each roll examined. exceeds the applicable acceptance n

40、umber specified in table II, the lot shall be rejected. If the total number of overall defects in the sample rolls Defects Off Shade Class 2 cloth - character of finish not equal to that of standard sample Overall uncleanness Width less than specified Objectionable odor, class 2 only NOTE: Normal re

41、sidual odor of chemicals commonly used to apply resins for finishing shall not be regarded as objectionable. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-q3352D 3 I 9999906 0393243 7 & I MIL-C-43352D TABLE 11. Sample size and acceptance cr

42、iteria Lot size Sample size Acceptance number 2/ (yards) (rolls) up to 1200 inclusive I/ 1201 up to and including 3200 5 35,001 up to and including 150,000 20 3 3201 up to and including 10,000 8 10,001 up to and including 35,000 13 150,001 and over 32 - i/ If a lot contains fewer than three rolls, e

43、ach roll in the lot shall be examined. - 2/ Applicable to 4.4.2.2 and 4.4.2.3. .:* * 4.4.2.3 Length examination. Each roll used in the yard-by-yard examination shall be examined for the defects listed below. If the total number of these defects in the sample rolls exceeds the applicable acceptance n

44、umber specified in table II or if the total of the actual gross lengths of rolls in the sample is less than the total of the gross lengths marked on the roll tickets, the lot shall be rejected. Defects Any length on roll found to be less than the minimum specified. O Total length of roll is 2 or mor

45、e yards less than that marked on ticket. Any roll containing more than three pieces. Any piece in roll less than 50 yards in length. * 4.4.2.4 Shade and appearance examination. During the yard-by-yard examination, each roll in the sample shall be examined for shade and finish appearance. Any roll in

46、 the sample off shade or shaded side to side, side to center or end to end, shall be cause for rejection of the entire lot represented by the sample. * 4.4.2.5 Roll identification examination. During the yard-by-yard examination, each roll in the sample shall be examined. unacceptable if two or more

47、 rolls in the sample are not labeled or ticketed in accordance with the Textile Fiber Products Identification Act. The lot shall be 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-93352D 83 m 997770b 0393242 9 U - MIL-C-43352D 4.4.3 End item

48、testing. The cloth shall be tested for the characteristics listed in table III. The methods of testing specified in FED-STD-191 wherever applicable, and as listed in table III, shall be followed. The physical and chemical values specified in Section 3 apply to the average of the determinations made

49、on a sample unit for test purposes as specified in the applicable test method. The sample unit shall be 1 continuous yard, full width, of the finished cloth. The lot size shall be expressed in units of 1 linear yard and the sample size (number of sample units) shall be as specified below. The lot shall be unacceptable if any sample unit fails to meet any test requirement specified. All test reports shall contain the indi