ANSI UL 330-2017 UL Standard for Safety Hose and Hose Assemblies for Dispensing Flammable Liquids (Eighth Edition)《配送易燃性液体用软管和软管组件的安全性标准》.pdf

《ANSI UL 330-2017 UL Standard for Safety Hose and Hose Assemblies for Dispensing Flammable Liquids (Eighth Edition)《配送易燃性液体用软管和软管组件的安全性标准》.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 330-2017 UL Standard for Safety Hose and Hose Assemblies for Dispensing Flammable Liquids (Eighth Edition)《配送易燃性液体用软管和软管组件的安全性标准》.pdf（41页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 330 Hose and Hose Assemblies for Dispensing Flammable Liquids STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL

2、COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose and Hose Assemblies for Dispensing Flammable Liquids, UL 330 Eighth Edition, Dated June 30, 2017 SUMMARY OF TOPICS The Eighth Edition of the Standard for Safety for

3、 Hose and Hose Assemblies for Dispensing Flammable Liquids, UL 330, is being published to reect the latest ANSI recognition date and to incorporate the following changes in requirements: 1. Revision to requirement for samples in the tensile strength and elongation tests 2. Clarication of ethanol lev

4、el and fuels not covered by the standard The revised requirements are substantially in accordance with Proposal(s) on this subject dated May 19, 2017. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic

5、, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liabl

6、e for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of s

7、uch damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, d

8、amage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. JUNE 30, 2017 UL 330 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTIO

9、N WITHOUT PERMISSION FROM UL JUNE 30, 2017 UL 330 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 30, 2017 1 UL 330 Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids The First edition was tit

10、led the Standard for Construction of Rubber Hose for Conducting Gasoline The Second edition was titled the Standard for 3/4-, 1-, and 1-1/4-inch Hose for Conducting Gasoline The Third edition was titled the Standard for Hose for Conducting Gasoline The Fourth edition was titled the Standard for Gaso

11、line Hose The Fifth edition was titled the Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids First Edition September, 1917 Second Edition March, 1937 Third Edition July, 1950 Fourth Edition June, 1973 Fifth Edition August, 1978 Sixth Edition August, 1996 Seventh Edition December

12、, 2009 Eighth Edition June 30, 2017 This ANSI/UL Standard for Safety consists of the Eighth Edition. The most recent designation of ANSI/UL 330 as an American National Standard (ANSI) occurred on June 29, 2017. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, and Titl

13、e Page. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at https:/. ULs Standards for Safety are copyrighted by UL. Neither a prin

14、ted nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2017 UNDERWRITERS LABORATORIES INC. ANSI/UL 330-2017UL COPYRIGHTED MATERIAL NOT

15、AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS IN

16、TRODUCTION 1 Scope .6 2 General 6 2.1 Units of measurements6 2.2 Undated references .7 3 Glossary .7 CONSTRUCTION 4 Tube and Cover 8 4.1 Single-line hose and double-line vapor recovery hose.8 4.2 Coaxial vapor recovery hose .8 5 Thickness of Cover8 6 Internal Diameter .9 7 Reinforcement .10 8 Electr

17、ical Bonding10 9 Couplings .10 PERFORMANCE 10 General11 11 Repeated Bending Test (Empty) 11 11.1 General .11 11.2 Sample .11 11.3 Apparatus .11 11.4 Method .11 12 Hydrostatic Strength Test 13 12.1 General .13 12.2 Sample .13 12.3 Apparatus .13 12.4 Method .14 13 Resistance To External Pressure .14 1

18、3.1 General .14 13.2 Sample .14 13.3 Apparatus .14 13.4 Method .14 14 Repeated Bending Test (Filled).15 14.1 General .15 14.2 Sample .15 14.3 Apparatus .15 14.4 Method .16 15 Permeation Test (For Low Permeation Hose) 16 15.1 General .16 15.2 Test equipment 16 15.3 General test procedure and instruct

19、ions .17 15.4 Samples 18 15.5 Pretest procedure 18 15.6 Preconditioning procedure .19 15.7 Permeation test procedure 19 JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION

20、 FROM UL 15.8 Steady state criteria 20 16 Electrical Resistance Tests for Hose Having Nonmetallic Electrically Conductive Materials 21 16.1 General .21 16.2 Samples 21 16.3 Apparatus .21 16.4 Method .21 17 Leakage and Electrical Continuity Test 22 17.1 General .22 17.2 Sample .22 17.3 Apparatus .22

21、17.4 Method .23 18 Swivel Joint Operation Test 23 18.1 General .23 19 Pull Test .23 19.1 General .23 19.2 Sample .23 19.3 Equipment.24 19.4 Method .24 20 Adhesion Test 24 20.1 General .24 20.2 Sample .25 20.3 Apparatus .25 20.4 Method .25 21 Deformation Test .25 22 Kink Test 26 23 Tensile Strength a

22、nd Elongation Tests 26 23.1 General .26 23.2 Samples 26 23.3 Apparatus .27 23.4 Method .27 24 Accelerated Air Oven Aging Test .28 24.1 General .28 24.2 Samples 28 24.3 Apparatus .28 24.4 Method .28 24.5 O-rings29 25 Ozone Exposure Test .29 25.1 General .29 25.2 Samples 29 25.3 Apparatus .29 25.4 Met

23、hod .29 26 Ultraviolet Light and Water Exposure Test .30 26.1 General .30 26.2 Sample .30 26.3 Apparatus .30 26.4 Method .30 27 Immersion Tests 31 27.1 Tensile strength and ultimate elongation 31 27.2 Samples 31 27.3 Apparatus .32 27.4 Method .32 27.5 Volume change 32 27.6 O-rings, gaskets, and seal

24、ing materials .34 JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 28 Low Temperature Test 34 28.1 General .34 28.2 Sample .35 28.3 Apparatus .35 28.4 Method .3

25、5 28.5 O-rings35 MANUFACTURING AND PRODUCTION TESTS 29 General35 MARKING 30 Details.36 JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1

26、 These requirements cover hose and hose assemblies, including vapor recovery hose and assemblies, for use on dispensing devices for ammable liquids. A ammable liquid hose assembly consists of exible hose and ttings suitable for attachment to ammable liquid dispensing equipment. For the purpose of th

27、is Standard ammable liquids are gasoline and diesel fuel. The term “gasoline” includes gasoline with small amounts of additives such as detergents, solvents for detergents, and anti-icing chemicals and gasoline with up to 10 percent ethanol. 1.2 Hose assemblies are intended for use in accordance wit

28、h the Automotive and Marine Service Station Code of National Fire Protection Association, NFPA 30A. 1.3 These requirements cover hose and hose assemblies (hose with couplings attached) in sizes up to and including 1-1/2 inches (38.1 mm). 1.4 Hose for conveying liquid fuel is intended for use at a ma

29、ximum working pressure of 50 psig (345 kPa). Hose for conveying vapors of fuel is intended for use at a maximum working pressure of 0.5 psig (3.4 kPa), including slight negative pressures from vapor assist systems. 1.5 These requirements cover hose and hose assemblies for use at temperatures down to

30、 minus 40C (minus 40F) or minus 54C (minus 65F). 1.6 These requirements also cover fuel hose assemblies designated as “low permeation”, intended for use on dispensing devices for ammable liquids. For the purposes of this standard, permeation is considered to encompass fuel loss through the exible ho

31、se, fuel loss at the ttings and fuel loss at the connection between the hose assembly and the equipment to which it is intended to be attached in the dispensing system. 1.7 These requirements do not cover hose or hose assemblies, intended for use in automotive vehicles or in conned areas, except for

32、 locations inside the housings of dispensing devices complying with the Standard For Power-Operated Dispensing Devices For Petroleum Products, UL 87. 2 General 2.1 Units of measurements 2.1.1 When a value for measurement is followed by a value in other units in parentheses, the rst stated value is t

33、he requirement. JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the requi

34、rements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purposes of this outline, the following denitions apply. 3.2 ADJUSTED MASS LOSS The mass loss of the blank (unlled hose assembly) subtracted from the mass loss of a lled

35、hose assembly. The purpose of this is to adjust for factors other than fuel permeation that may affect mass loss. 3.3 BALANCE VAPOR RECOVERY HOSE ASSEMBLY A coaxial hose consisting of an inner line for conveying fuel and an outer line. Fuel vapors are permitted to return to the fuel dispenser in the

36、 annular space between the two lines. 3.4 HOSE ASSEMBLY VOLUME (V) The total volume in cubic centimeters of a capped hose assembly, calculated as follows: V=D 2 (L + 2d) /4 in which: D = the inner diameter of the hose in centimeters, as determined in 15.5.3 L = the length of the hose in centimeters,

37、 as determined in 15.5.1 d = the depth of the cap in centimeters, as determined in 15.5.2 3.5 LEAST SQUARES FIT LINE A best t line drawn through a set of data such that the sum of the squared residuals has its least value, a residual being the difference between an observed value (data point) and th

38、e line. 3.6 PERMEATION SURFACE AREA The length of the hose as determined in 15.5.1 multiplied by the inner circumference of the hose, expressed in square meters. For vacuum-assist vapor recovery hose, the length of the hose is multiplied by the inner circumference of the outer hose. For balance vapo

39、r recovery hose, the length of the hose is multiplied by the average inner circumference of the outer hose. 3.7 REINFORCEMENT Natural or synthetic bers or fabric, or metallic wire that is wrapped, braided or spiral wound in one or more layers over the tube, intended to provide longitudinal and trans

40、verse (hoop) strength to the hose. 3.8 VACUUMASSIST VAPOR RECOVERY HOSE ASSEMBLY A coaxial hose consisting of an inner vacuum line for vapor recovery and an outer line. Fuel is dispensed through the annular space between the two lines. JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE

41、LIQUIDS - UL 330 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONSTRUCTION 4 Tube and Cover 4.1 Single-line hose and double-line vapor recovery hose 4.1.1 The tube shall be made from a material resistant to gasoline and diesel fuel. 4.1.

42、2 The cover shall be made from a material resistant to gasoline, diesel fuel, oils, and ozone. 4.1.3 The tube and cover shall be of uniform thickness, and free from pitting, blisters, or other imperfections. This requirement is not intended to exclude the use of a corrugated cover. 4.2 Coaxial vapor

43、 recovery hose 4.2.1 The tube and cover, if any, of the inner hose shall be made from materials resistant to gasoline and diesel fuel. 4.2.2 The tube of the outer hose or a homogeneous outer hose shall be made from materials resistant to gasoline and diesel fuel. 4.2.3 The cover of the outer hose or

44、 a homogeneous outer hose shall be made from a material resistant to gasoline, diesel fuel, oil, and ozone. An outer homogeneous thermoplastic hose with no separate layer of reinforcement shall also be made from a material resistant to sunlight. 4.2.4 The tube and cover shall be of uniform thickness

45、 and free from pitting, blisters, or other imperfections. This requirement is not intended to exclude the use of a corrugated tube, cover, or outer vapor hose. 5 Thickness of Cover 5.1 The thickness of the cover shall not be less than 0.047 inch (1.19 mm) when measured in accordance with 5.2 5.6. Ex

46、ception: This requirement does not apply to the cover of the inner hose and the outer vapor hose of a coaxial type vapor recovery hose. 5.2 For removing irregularities in samples, the buffing machine or skiving machine outlined in the Standard Practice for Rubber Preparation of Product Pieces for Te

47、st Purposes from Products, ASTM D3183, is to be used. 5.3 The abrasive wheel of the buffing machine is to be No. 30 60 grit and the diameter and rotary velocity of the wheel are to be such that it will have a peripheral speed of 4000 700 feet per minute (20.3 3.6 m/s). The machine is to be provided

48、with a slow feed so that very little compound can be removed at one cut to avoid overheating of the specimen. JUNE 30, 2017 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5

49、.4 A dial micrometer graduated to 0.001 inch (0.03 mm) that exerts a load of 2.82 3.00 ounces (80 85 grams) by means of a weight is to be used to measure thickness. The load is to be applied through a at contact foot 0.25 0.01 inch (6.4 0.3 mm) in diameter. 5.5 To determine the thickness of the tube and cover, a strip,68inches (152.4 203.2 mm) long and 1 inch (25.4 mm) wide, or as close to 1 inch (25.4 mm) as possible from small diameter hose, is to be cut longitudinally