BS PD CEN TS 14416-2014 Geosynthetic barriers Test method for determining the resistance to roots《土工合成物隔层 测定底部阻力的试验方法》.pdf

《BS PD CEN TS 14416-2014 Geosynthetic barriers Test method for determining the resistance to roots《土工合成物隔层 测定底部阻力的试验方法》.pdf》由会员分享，可在线阅读，更多相关《BS PD CEN TS 14416-2014 Geosynthetic barriers Test method for determining the resistance to roots《土工合成物隔层 测定底部阻力的试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication PD CEN/TS 14416:2014 Geosynthetic barriers Test method for determining the resistance to rootsPD CEN/TS 14416:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of CEN/ TS 14416:2014. It supersedes DD CEN/TS 14416:2005 which is withdr

2、awn. The UK participation in its preparation was entrusted to Technical Committee B/553, Geotextiles and geomembranes. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a con

3、tract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 83315 1 ICS 59.080.70 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under

4、 the authority of the Standards Policy and Strategy Committee on 31 March 2014. Amendments issued since publication Date Text affectedPD CEN/TS 14416:2014TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 14416 February 2014 ICS 59.080.70 Supersedes CEN/TS 14416:2005 Engl

5、ish Version Geosynthetic barriers - Test method for determining the resistance to roots Barrires gosynthtiques - Mthode dessai pour la dtermination de la rsistance aux racines Geosynthetische Dichtungsbahnen - Prfverfahren zur Bestimmung des Widerstandes gegen Wurzeln This Technical Specification (C

6、EN/TS) was approved by CEN on 9 December 2013 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a

7、 European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until t

8、he final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Icela

9、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Manage

10、ment Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 14416:2014 EPD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 5 2 Principle 5 3 App

11、aratus .5 4 Procedure .5 5 Evaluation .6 6 Test report 6 Bibliography 7 PD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 3 Foreword This document (CEN/TS 14416:2014) has been prepared by Technical Committee CEN/TC 189 “Geosynthetics”, the secretariat of which is held by NBN. This document supersedes CEN/T

12、S 14416:2005. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standard

13、s organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

14、Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 4 Introduction This Technical Specification defines a method for testing the resistance of a geosynthetic barri

15、er to penetration by roots. Such resistance is a requirement for many uses of geosynthetic barriers. This Technical Specification does not purport to address all safety problems, if any, associated with its use. PD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 5 1 Scope This Technical Specification descri

16、bes a laboratory procedure for the rapid testing of the resistance of polymeric, bituminous or clay geosynthetic barriers to root penetration. It is suitable for testing of welded seams or other areas of potential weakness. A longer test that may be more suitable for testing the long-term resistance

17、 of geosynthetic barriers is described in EN 13948. 2 Principle A section of geosynthetic barrier is placed in soil into which seeds are sown. Six to eight weeks later the geosynthetic barrier is examined to see whether it has been penetrated by the roots of the young plants. 3 Apparatus The followi

18、ng equipment shall be used: four dry unglazed clay flower pots approximately 220 mm high. The diameter at the base of the pot shall be approximately 140 mm, the diameter at the top 250 mm, and the angle between side and central axis approximately 13. A 40 mm wide band shall be painted on the inside

19、of the pot, about 100 mm above the base, and allowed to dry; lime-free soil (pH 5 to 6), mixed with a little loam or high quality potting soil; Compost should not be used. lupin seeds (lupinus alba); silicone mastic sealant or mortar-sand mixture; bitumen 85/40; glass tubes; anti-mould agent. 4 Proc

20、edure Fill the pots with the soil as far as the lower edge of the painted band, then seal and humidify. Cut three discs of geosynthetic barrier to cover the soil exactly. Place the geosynthetic barrier on the soil of three of the pots with the upper side uppermost. Carefully seal the gap between geo

21、synthetic barrier and pot with the sealant or mortar-sand mixture. Prepare the fourth pot in which the geosynthetic barrier is replaced by a 20 mm thick layer of bitumen 85/40 (oxidized grade bitumen with a softening point of (85 5) C and a penetration temperature of (40 5) C). Cover the geosyntheti

22、c barrier or the bitumen with 90 mm of soil, then seal and humidify. PD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 6 Sow 30 to 40 lupin seeds in each pot evenly on the soil, and pre-treat with anti-mould agent. Cover the seeds with 10 mm of light soil. In summer, place the pots outside. In winter, plac

23、e them in a heated greenhouse with additional artificial light. Moisten the soil above the geosynthetic barrier or bitumen by pouring rain water as necessary into a glass tube that extends down as far as the geosynthetic barrier. If no rain water is available use a 1:1 mixture of tap water and disti

24、lled water. 5 Evaluation After six weeks (eight weeks in winter) empty the pots and inspect the upper and lower surface of the geosynthetic barrier for roots that have penetrated into it or through it. Inspect the bitumen layer. If the roots have not penetrated the bitumen, the test shall be repeate

25、d. NOTE This is a control of the vitality of the plants. 6 Test report The test report shall include the following information: a) reference to this Technical Specification and to the method; b) test laboratory; c) identification of the product tested; d) number of specimens; e) test duration; f) ob

26、served results, stating whether the roots have penetrated the geosynthetic barrier and the bitumen, accompanied by relevant photographs; g) date of testing. PD CEN/TS 14416:2014 CEN/TS 14416:2014 (E) 7 Bibliography 1 EN 13948, Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets fo

27、r roof waterproofing - Determination of resistance to root penetration 2 EN ISO 10318, Geosynthetics - Terms and definitions (ISO 10318) This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related

28、publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited. British Standards Institution (BSI) BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK About us We bring together bus

29、iness, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions. The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations

30、 of all sizes and across all sectors choose standards to help them achieve their goals. Information on standards We can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team o

31、r Knowledge Centre. Buying standards You can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards De

32、velopment Organizations, hard copies can be ordered from our Customer Services team. Subscriptions Our range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to With British Standards Online (BSOL) youll have insta

33、nt access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both i

34、n single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Memb

35、er and the benefits of membership, please visit With a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is cur

36、rent. For further information, email . Revisions Our British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI

37、publication please inform the Knowledge Centre. Copyright All the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international s

38、tandardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photoco

39、pying, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department. Useful Contacts: Customer Services Tel: +44 845 086 9001 Email (orders): Email (enquiries): Subscriptions Tel: +44 845 086 9001 Email: Knowledge Centre Tel: +44 20 8996 7004 Email: Copyright & Licensing Tel: +44 20 8996 7070 Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW