BS ISO 9136-1-2005 Abrasive grains - Determination of bulk density - Macrogrits《磨料颗粒 体密度的测定 粗磨粒》.pdf

《BS ISO 9136-1-2005 Abrasive grains - Determination of bulk density - Macrogrits《磨料颗粒 体密度的测定 粗磨粒》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9136-1-2005 Abrasive grains - Determination of bulk density - Macrogrits《磨料颗粒 体密度的测定 粗磨粒》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 9136-1:2004 Abrasive grains Determination of bulk density Part 1: Macrogrits ICS 25.100.70 BS ISO 9136-1:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 February 2005 BSI 16 February 2005 ISBN 0 580 45469 X Nat

2、ional foreword This British Standard reproduces verbatim ISO 9136-1:2004 and implements it as the UK national standard. It supersedes BS 7425-1:1991 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper and clo

3、ths, and powders, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under

4、 the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct appli

5、cation. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; mo

6、nitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 5 and a back cover. The BSI copyright notice displayed in this document i

7、ndicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 9136-1:2004(E) OSI 4002INTERNATIONAL STANDARD ISO 9136-1 First edition 2004-10-15 Abrasive grains Determination of bulk density Part 1: Macrogrits Grains abrasifs Dtermination

8、de la masse volumique apparente Partie 1: Macrograins BSISO91361:2004IS-6319 O1:(4002E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess the typefaces whice era hml era deddebics

9、nede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo t

10、eh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit g

11、no it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 4002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh r

12、epmissii non writign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o gr We bwww.is.o gro Pulbisdehi n Switlrez dnaii ISO 4002 Allr ith

13、gsr esedevrBSISO91361:2004IS-6319 O1:(4002E) I SO 4002 All irthgs ersedevr iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through IS

14、O technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates c

15、losely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. D

16、raft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this do

17、cument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9136-1 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. This first edition of ISO 9136-1 cancels and replaces

18、ISO 9136:1989, the contents of which have been technically revised. ISO 9136 consists of the following parts, under the general title Abrasive grains Determination of bulk density: Part 1: Macrogrits Part 2: Microgrits BSISO91361:2004blank 4002:16319OSISBINTENRATIONAL TSANDADR IS-6319 O1:(4002E)I SO

19、 4002 All irthgs ersedevr 1Abrasive grains Determination of bulk density Part 1: Macrogrits 1 Scope This part of ISO 9136 specifies a test method for the determination of the bulk density of bonded and coated abrasive macrogrits. 2 Normative references The following referenced documents are indispen

20、sable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6344-1, Coated abrasives Grain size analysis Part 1: Grain size distribution test ISO 8486-1

21、, Bonded abrasives Determination and designation of grain size distribution Part 1: Macrogrits F4 to F220 ISO 9136-2, Abrasive grains Determination of bulk density Part 2: Microgrits 3 Definitions For the purposes of this document, the definitions given in ISO 6344-1, ISO 8486-1 and ISO 9136-2 apply

22、. 4 Apparatus 4.1 General The test apparatus is illustrated in Figure 1 and Annex A. It consists of the elements listed in 4.2 to 4.6. 4.2 Stand An exact description of the stand is not necessary. The only requirement is that it be capable of holding the funnel in a vertical position so that the dim

23、ension between the outlet of the funnel and the bottom of the measuring cylinder is 138 1 mm. 4.3 Funnel The slope of the funnel shall be such that fine grains will not adhere to the sides. By preference, the funnel shall be made of stainless steel with smooth inside seams. Its dimensional character

24、istics (see also Figure 1) shall be as follows: BSISO91361:2004IS-6319 O1:(4002E) 2 I SO 4002 All irthgs ersedevr total height of funnel: 240 mm; diameter of top: 160 mm; inside diameter of the cylindrical outlet: 20 mm 0,5 mm; height of the cylindrical outlet area: 40 mm 1 mm. 4.4 Funnel release va

25、lve An exact description of the funnel release valve is not necessary. The only requirement is that quick opening of the valve be ensured. Figure 1 illustrates an example of a swinging stopper release valve. 4.5 Measuring cylinder The measuring cylinder is cylindrical with a polished inner surface a

26、nd features a volume V of (200 0,5) cm 3 ; this volume is determined by an inner diameter of 64 mm and an inner height of 62,2 mm. The measuring cylinder is placed centrally under the stream emmanating from the vibration channel. The height of fall of the macrogrits to be tested (from the upper edge

27、 of the channel bottom to the bottom of the measuring cylinder) shall be (138 1) mm. 4.6 Overspill tray The overspill tray with a flat bottom serves as a collector for overflowing macrogrits. The measuring beaker is placed in the drip tray. 5 Calibration of the measuring cylinder Calibration of the

28、measuring cylinder can be achieved by the following two methods. The volume of the measuring cylinder shall be checked regularly. Method A The dry, empty measuring cylinder is weighed together with a flat glass plate. The measuring cylinder is filled with water and the glass plate placed on the cyli

29、nder in such a way that no air bubbles are present. The glass plate is held in this position, the surplus water removed and the total weight determined. The volume is calculated as follows: 2 0 HO m V = (1) where V is the volume of the measuring cylinder, in cubic centimetres; m 0is the mass of wate

30、r, in grams; H 2 Ois the density of water, in grams per cubic centimetre, at the measuring temperature, see Table 1. Method B The volume is calculated by measuring the internal dimensions of the cylinder (margin of error 0,001 mm). BSISO91361:2004IS-6319 O1:(4002E) I SO 4002 All irthgs ersedevr 3Tab

31、le 1 Density of purified water Temperature C Density g/cm 3Temperature C Density g/cm 318 0,998 593 26 0,996 780 20 0,998 201 28 0,996 230 22 0,997 767 24 0,997 293 30 0,995 643 6 Method of measurement 6.1 Preparation of samples For grain sizes F100 or P100 and finer, dry the abrasive grains at a te

32、mperature of 110 C for 1 h and then, prior to measurement, cool them to room temperature. Coarser grains shall be dry at room temperature. 6.2 Procedure Fill a 250 ml beaker to the top with the abrasive grains to be tested. With the funnel outlet closed and the measuring cylinder centering under the

33、 outlet of the funnel, pour the grains into the funnel. Open the outlet of the funnel and allow the grains to fall freely until the funnel is empty. Avoid vibrations throughout this procedure. The test material heaped above the rim of the measuring cylinder shall be removed using a straight blade wi

34、th the leading edge at an angle of approximately 45 to the rim of the measuring beaker (see Figure 2). Vibration shall be avoided throughout the measuring procedure (risk of compaction). The measuring cylinder filled with macrogrits shall be weighed to within 0,01 g. 7 Expression of results 7.1 Meth

35、od of calculation Calculate the bulk density Bas follows: 1 B m V = (2) where Bis the bulk density, in grams per cubic centimetre; m 1is the mass of grains contained in the measuring cylinder, in grams; V is the volume of the cylinder, in cubic centimetres. 7.2 Repeatability Duplicate determinations

36、 by the same operator and apparatus shall not differ by more than 0,02 g/cm 3 . BSISO91361:2004IS-6319 O1:(4002E) 4 I SO 4002 All irthgs ersedevrDimensions in millimetres Key 1 funnel 5 overspill dish 2 funnel stand height adjustment 6 measuring cylinder 3 stand 7 release valve (closed) 4 bottom pla

37、te aOutlet diameter. Figure 1 Apparatus for the determination of the bulk density of abrasive macrograins Dimensions in millimetres Key 1 straight blade aMoving direction. Figure 2 Procedure for removing the heaped material BSISO91361:2004IS-6319 O1:(4002E) I SO 4002 All irthgs ersedevr 5Annex A (in

38、formative) Apparatus for the determination of the bulk density of macrogrits Key 1 overspill tray 2 measuring cylinder 3 stand 4 funnel Figure A.1 Apparatus for the determination of the bulk density of macrogrits BSISO91361:2004BS ISO 9136-1:2004 BSI 389 Chiswick High Road London W4 4AL BSI British

39、Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of Briti

40、sh Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the

41、technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buyi

42、ng standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for internatio

43、nal standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technic

44、al Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with s

45、tandards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards v

46、ia British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies.

47、Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use,

48、 in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.