ISO 6460-1 AMD 1-2015 Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 1 General test requirements Amendment 1《摩托车 废气排.pdf

《ISO 6460-1 AMD 1-2015 Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 1 General test requirements Amendment 1《摩托车 废气排.pdf》由会员分享，可在线阅读，更多相关《ISO 6460-1 AMD 1-2015 Motorcycles - Measurement method for gaseous exhaust emissions and fuel consumption - Part 1 General test requirements Amendment 1《摩托车 废气排.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2015 Motorcycles Measurement method for gaseous exhaust emissions and fuel consumption Part 1: General test requirements AMENDMENT 1 Motocycles Mthode de mesure des missions de gaz dchappement et de la consommation de carburant Partie 1: Exigences gnrales dessai AMENDEMENT 1 INTERNATIONAL STAND

2、ARD ISO 6460-1 First edition 2007-08-15 Reference number ISO 6460-1:2007/Amd.1:2015(E) AMENDMENT 1 2015-11-01 ISO 6460-1:2007/Amd.1:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this

3、publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the

4、country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.org ISO 6460-1:2007/Amd.1:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federa

5、tion of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committ

6、ee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and

7、those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part

8、2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the

9、 document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific ter

10、ms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information. Amendment 1 to ISO 6460-1 was prepared by ISO/TC22, Road vehicle, Subcommittee S

11、C38, Motorcycles and mopeds. ISO 2015 All rights reserved iii Motorcycles Measurement method for gaseous exhaust emissions and fuel consumption Part 1: General test requirements AMENDMENT 1 Page 45, Annex F Replace Formula (F.4) with the following: * (F.4) ISO 6460-1:2007/Amd.1:2015(E) ISO 2015 All rights reserved 1 ISO 6460-1:2007/Amd.1:2015(E) ISO 2015 All rights reserved ICS 13.040.50; 43.140 Price based on 1 page