ASTM C1172-2019 Standard Specification for Laminated Architectural Flat Glass.pdf

《ASTM C1172-2019 Standard Specification for Laminated Architectural Flat Glass.pdf》由会员分享，可在线阅读，更多相关《ASTM C1172-2019 Standard Specification for Laminated Architectural Flat Glass.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1172 14C1172 19Standard Specification forLaminated Architectural Flat Glass1This standard is issued under the fixed designation C1172; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numbe

2、r in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the quality requirements of flat laminated glass consisting of two or more lites of glass bonded withan interlaye

3、r material for use in building and related applications.1.2 Depending on the number, thickness, and treatment of lites, and the number and thickness of interlayers, the glass shall belaminated for applications including, but not limited to, safety, security, detention, hurricane/cyclic-wind resistan

4、ce, blastresistance, bullet resistance, sound reduction, and decorative glazing.1.3 Optical distortion and the evaluation thereof are not currently within the scope of the standard. Mockups are recommendedas a method to evaluate glass. (See Appendix X1.)1.4 The dimensional values, except thickness d

5、esignations, stated in inch-pound units are to be regarded as the standard. Thevalues in parentheses are for information only.1.5 The following safety hazards caveat pertains only to the test method portion, Section 7, of this specification: This standarddoes not purport to address all of the safety

6、 concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability ofregulatory limitations prior to use.1.6 This international standard was developed in ac

7、cordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 Refe

8、rence to these documents shall be the latest revision unless otherwise specified by the authority applying thisspecification.2.2 ASTM Standards:2C162 Terminology of Glass and Glass ProductsC1036 Specification for Flat GlassC1048 Specification for Heat-Strengthened and Fully Tempered Flat GlassC1376

9、Specification for Pyrolytic and Vacuum Deposition Coatings on Flat GlassC1422 Specification for Chemically Strengthened Flat GlassC1503 Specification for Silvered Flat Glass MirrorE308 Practice for Computing the Colors of Objects by Using the CIE SystemE413 Classification for Rating Sound Insulation

10、E903 Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating SpheresE1332 Classification for Rating Outdoor-Indoor Sound AttenuationE1886 Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted byMissile(s

11、) and Exposed to Cyclic Pressure DifferentialsE1996 Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted byWindborne Debris in HurricanesE2395 Specification for Voluntary Security Performance of Window and Door Assemblies with Glazing Impact

12、1 This specification is under the jurisdiction ofASTM Committee C14 on Glass and Glass Products and is the direct responsibility of Subcommittee C14.08 on Flat Glass.Current edition approved Sept. 15, 2014Feb. 1, 2019. Published October 2014February 2019. Originally approved 1991. Last previous edit

13、ion approved 20092014 asC1172 09C1172 14.1. DOI: 10.1520/C1172-14.10.1520/C1172-19.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary pag

14、e on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that u

15、sers consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Cons

16、hohocken, PA 19428-2959. United States1F1233 Test Method for Security Glazing Materials And SystemsF1642 Test Method for Glazing and Glazing Systems Subject to Airblast LoadingsF1915 Test Methods for Glazing for Detention FacilitiesF3006 Specification for Ball Drop Impact Resistance of Laminated Arc

17、hitectural Flat GlazingF3007 Test Method for Ball Drop Impact Resistance of Laminated Architectural Flat Glass2.3 ANSI Standard:Z97.1 Safety Glazing Materials Used in BuildingsSafety Performance Specifications and Methods of Tests32.4 Federal Document:4CPSC 16CFR1201 Consumer Product Safety Commissi

18、on Safety Standard for Architectural Glazing Materials2.5 National Institute of Justice (NIJ) Standard:5NIJ 0108.1 Ballistic Resistant Protective Materials2.6 UL Standards:6UL 752 Standard for Bullet Resisting MaterialsUL 972 Standard for Burglary Resisting Glazing Materials3. Terminology3.1 Definit

19、ions:3.1.1 Refer to Terminology C162, Specifications C1036 or C1048, as appropriate.3.1.2 blemishes in flat glassRefer to Specifications C1036 or C1048, as appropriate.3.2 Definitions of Terms Specific to This Standard:3.2.1 adhesion chipsSee fuse.3.2.2 blow-ina separation of glass and interlayer at

20、 or close to the laminate edge caused by penetration of the autoclavingmedium into the edge during manufacturing.3.2.3 boil (bubble)a gas pocket in the interlayer material or between the glass and interlayer.3.2.4 covered edgethe peripheral area of the laminate covered by the channel or sash when in

21、stalled.3.2.5 delaminationa condition in which separation has occurred between the glass lite(s) and the interlayer.3.2.6 discolorationa visibly noticeable color change (from original) in the appearance of a material.3.2.7 distortionthe inability to see an image clearly; the image is twisted out of

22、natural shape.3.2.8 edge boilSee boil (bubble).3.2.9 exposed edgethe peripheral area of the laminate exposed to the environment after installation.3.2.10 fusea glass particle or crystalline material that is permanently bonded to a surface of a lite.3.2.11 haira slender, pigmented filament from human

23、 or animal epidermis or other thread-like filament.3.2.12 inside dirtforeign material trapped inside the laminate.3.2.13 interlayera layer or multiple layers of material acting as an adhesive between lites of glass which add(s) additionalperformance to the finished product, for example, impact resis

24、tance, solar control, acoustical insulation, color, design, orcombinations thereof.3.2.14 laminated glassan assembly consisting of two or more lites of glass, conforming to Specifications C1036 or C1048,that are bonded together by interlayer material.3.2.15 lintshort fibers of yarn or fabric trapped

25、 within the laminate.3.2.16 lite or lighta panel or sheet of glass or a panel or sheet of laminated glass.3.2.17 mismatchmisalignment of the edges of two lites of glass, when laminated.3.2.18 offsetglass lites that are intentionally not aligned in a laminate.3.2.19 rubabrasion of a glass surface pro

26、ducing a frosted appearance; also known as a scuff.3.2.20 separationan area of the laminate that has become delaminated (see delamination).3.2.21 shineran area on a glass edge that has not been ground or polished.3.2.22 short interlayera condition of the laminate in which the interlayer does not ext

27、end to the edge.3.2.23 streaka noticeably visible directional blemish or discoloration on or in the laminated unit.3 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.4 Available from U.S. Consumer Product Safety Commission

28、 (CPSC), 4330 East West Hwy., Bethesda, MD 20814, http:/www.cpsc.gov.5 Available from National Institute of Justice (NIJ), 810 7th St., NW, Washington, DC 20531, http:/www.ojp.usdoj.gov/nij.6 Available from Underwriters Laboratories (UL), 333 Pfingsten Rd., Northbrook, IL 60062-2096, http:/.C1172 19

29、23.2.24 templatea pattern used as a guide to define the overall size and shape of a cut lite.3.2.25 unlaminated areaan area of the laminate that failed to flow, develop acceptable optics, achieve adhesion, orcombinations thereof during the laminating process. This blemish may be discernible due to a

30、 texture, haze, or other change inappearance.4. Classification4.1 TypeLaminated flat glass furnished under this specification shall be of the following types, as specified:4.1.1 Type I - Laminated GlassAn assembly consisting of two or more lites of glass, conforming to Specifications C1036 orC1048,

31、that are bonded together by interlayer material.4.1.2 Type II - Laminated Safety GlassAn assembly of two or more lites of flat glass, conforming to Specifications C1036 orC1048, that are bonded together by interlayer material that meet the requirements ofANSI Z97.1 or CPSC 16CFR1201. In the caseof b

32、reakage, the interlayer serves to retain the glass fragments, limit the size of the opening and reduce the risk of cutting orpiercing injuries.4.2 ApplicationThe following terms are designed to guide the user to the appropriate inspection charts and requirements. Theglazing can usually, but not alwa

33、ys, be viewed in transmittance and reflectance.4.2.1 Laminated Proximate GlazingGlazing used in an installation in which the lower edge of the glazing is a maximum of6 ft (1.8 m) above the walking surface. The glazing is usually vertical, however, may also be sloping in or out from the verticalplane

34、. The glazing can be approached within 10 ft (3 m) or less (if distance is greater than 10 ft (3 m) see Laminated OverheadGlazing). Interior decorative glazing will be judged according to laminated vertical glazing criteria.4.2.2 Laminated Overhead GlazingGlazing used in an installation in which the

35、 lower edge of the glass is more than 6 ft (1.8m) above a walking floor level or cannot be approached within 10 ft (3 m). The glazing is usually sloping from the vertical plane,however, may also be vertical. Sloped glazing is considered any glazing that slopes more than 15 from the vertical in anydi

36、rection.4.2.3 Laminated Spandrel GlazingGlazing used in an installation in which the glazing is only viewed in reflection from thebuildings exterior. The glazing is usually installed vertically, however, may be at a slope to the vertical plane. Laminated spandrelglazing shall be inspected using the

37、criteria of laminated proximate glazing or laminated overhead glazing as defined in 4.2.1 or4.2.2.5. Ordering Information5.1 Purchasers should select the preferred options permitted in this specification and include the following information inprocurement documents:5.1.1 Title, number, and date of t

38、his specification.5.1.2 Type of laminated flat glass as referred to in this specification (see Section 4).5.1.3 Edgework requirements (see 8.2).5.1.4 Thickness requirements:5.1.4.1 Thickness designation of each individual lite of glass to be used in the laminate.5.1.4.2 Thickness designation of indi

39、vidual interlayer(s) used in the laminate.5.1.4.3 Overall nominal thickness of the laminate.5.1.5 Nominal length and width of the laminate.5.1.5.1 Blueprint, drawing, template, configuration specification, or other forms of information which detail overall size,configuration, and orientation.5.1.6 T

40、ypesColor, tint, coating, decorative effect, and strength of each individual lite of glass.5.1.7 Color, tint, type, formation, and decorative effect of the interlayer.5.1.8 The luminous transmittance of the laminate (see 7.13).5.1.9 Safety standards or regulations to which the laminate must conform.

41、5.1.10 All other standards as specified.5.2 Packaging RequirementsGlass packaging and protection will be standard manufacturer practice unless otherwisespecified. Consult manufacturer before specifying.6. Other Requirements6.1 Annealed glass lites shall conform to the requirements of Specification C

42、1036 for the incorporated glass type.6.2 Chemically strengthened glass lites shall conform to the requirements of Specification C1422.6.3 Heat strengthened or fully tempered glass lites shall conform to the requirements of Specification C1048.6.4 Mirror glass lites shall conform to the requirements

43、of Specification C1503.6.5 Pyrolytic and vacuum deposition coated glass lites shall conform to the requirements of Specification C1376.6.6 Solar and optical properties to be as specified.C1172 1936.7 Solar heat gain coefficient to be as specified.6.8 Sound transmission to be as specified in accordan

44、ce with Classifications E413 or E1332.6.9 Spandrel glass lites shall conform to the requirements of Specification C1048 for the incorporated glass type.6.10 Visible reflection to be as specified.6.11 Visible transmittance to be as specified.6.12 U-factor to be as specified.6.13 UV transmittance to b

45、e as specified.7. Test Methods7.1 Impact Test for Safety GlazingTest and interpret in accordance with ANSI Z97.1 or CPSC 16CFR1201, or both, asapplicable.7.2 Test for Missile Impact and Cyclic PressureTest and interpret in accordance with Test Method E1886 and SpecificationE1996.7.3 Test for Securit

46、y GlazingTest and interpret in accordance with Test Method F1233.7.4 Test for Glazing Subject to Airblast LoadingTest and interpret in accordance with Test Method F1642.7.5 Test for Detention GlazingTest and interpret in accordance with Test Method F1915.7.6 Test for Bullet Resisting GlazingTest and

47、 interpret in accordance with specified standards such as Test Method F1233, NIJ0108.1, and Standard UL 752.7.7 Test for Burglary Resisting GlazingTest and interpret in accordance with specified standards such as, but not limited to:Test Method F1233, NIJ 0108.1, and UL 972.7.8 Test for Impact Perfo

48、rmanceTest and interpret in accordance with Specifications E2395 and F3006, and Test MethodF3007.7.9 Color to be measured in accordance with Practice E308 using Illuminant C or D65.7.10 Overall BowPlace sample glass in a free-standing vertical position, with the longest edge resting on blocks at the

49、 quarterpoints. With the laminate in this position, place a straightedge across the concave surface, parallel to and within 1 in. (25.4 mm)of the edge, and measure the maximum deviation with a taper or feeler gage. A dial indicator may also be used.TABLE 1 Maximum Allowable Laminating Process Blemishes for Vertical Glazing, in. (mm)NOTE 1Refer to Specification C1036 for the quality specification for the individual glass lites.NOTE 2All imperfections noted should be separated by a minimum of 12 in. (300 mm).NOTE 3