IEC 62321-3-2-2013 Determination of certain substances in electrotechnical products - Part 3-2 Screening test methods - Screening of total bromine in polymers and electronics by co.pdf

《IEC 62321-3-2-2013 Determination of certain substances in electrotechnical products - Part 3-2 Screening test methods - Screening of total bromine in polymers and electronics by co.pdf》由会员分享，可在线阅读，更多相关《IEC 62321-3-2-2013 Determination of certain substances in electrotechnical products - Part 3-2 Screening test methods - Screening of total bromine in polymers and electronics by co.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62321-3-2 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Determination of certain substances in electrotechnical products Part 3-2: Screening Total bromine in polymers and electronics by Combustion Ion Chromatography Dtermination de certaines substances dans les produits lectro

2、techniques Partie 3-2: Mthodes dessai Brome total dans les polymres et les produits lectriques par Combustion Chromatographie dIonisation IEC 62321-3-2:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of thi

3、s publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or h

4、ave an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise s

5、ous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmenta

6、ires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electro

7、technical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that

8、you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives informatio

9、n on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds l

10、eading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc

11、 If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pou

12、r tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens uti

13、les: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Publishe

14、d CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes le

15、ctroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous do

16、nner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62321-3-2 Edition 1.0 2013-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Determination of certain substances in electrotechnical products Part 3-2: Screening Total bromine in polymers and electr

17、onics by Combustion Ion Chromatography Dtermination de certaines substances dans les produits lectrotechniques Partie 3-2: Mthodes dessai Brome total dans les polymres et les produits lectriques par Combustion Chromatographie dIonisation INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTE

18、CHNIQUE INTERNATIONALE V ICS 13.020; 43.040.10 PRICE CODE CODE PRIX ISBN 978-2-83220-840-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized dist

19、ributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 62321-3-2 IEC:2013 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions and abbreviations 8 3.1 Terms and definitions 8 3.2 Abbreviations 9 4 Prin

20、ciple . 9 4.1 Overview . 9 4.2 Principle of test . 10 5 Reagents and materials 10 6 Apparatus . 11 7 Sampling 12 8 Procedure. 12 8.1 Combustion . 12 8.2 IC analysis 13 8.3 Blank test 13 8.4 Cleaning and recalibration . 13 8.5 Calibration . 13 8.6 Measurement of the sample 14 8.7 Interference . 14 9

21、Calculation . 14 10 Precision 14 11 Quality assurance and control 15 11.1 General . 15 11.2 Limits of detection (LOD) and limits of quantification (LOQ) . 15 12 Test report 16 Annex A (informative) Oxygen bomb combustion-ion chromatography . 17 Annex B (informative) Oxygen flask combustion-ion chrom

22、atography . 22 Annex C (informative) Example of a combustion device and IC system 25 Annex D (informative) Results of international interlaboratory study #4A (IIS 4A) . 26 Annex E (informative) Additional results of TG 3-2 test 27 Annex F (informative) Additional validation data. 29 Annex G (informa

23、tive) Additional IC data . 30 Bibliography 31 Figure A.1 Example of the oxygen bomb combustion device 21 Figure B.1 Example of the oxygen flask combustion device 24 Figure B.2 Example of wrapping of sample 24 Figure C.1 Example of a combustion device connected to IC . 25 Figure C.2 Example of ion ch

24、romatographic system . 25 Figure G.1 Example of a chromatogram of the standard solution (4 mg/kg of each standard) by IC . 30 62321-3-2 IEC:2013 3 Table 1 Tested concentration ranges for bromine by C-IC in various materials . 7 Table 2 Acceptance criteria of items for quality control 15 Table 3 Stud

25、ents t values used for calculation of method detection limit (*MDL= t s n1 ) . 16 Table D.1 Mean results and recovery rates for total bromine obtained in the IIS4A study using C-IC . 26 Table D.2 Statistical total bromine data for IIS 4A results using C-IC . 26 Table E.1 Mean results and recovery ra

26、tes for total bromine obtained in the TG 3-2 internal test study by using C-IC . 27 Table E.2 Mean results and recovery rates for total bromine obtained in the TG 3-2 internal test study by using Oxygen bomb-IC 28 Table F.1 General conditions for the combustion furnace and the absorption solution 29

27、 Table F.2 Additional information Difference in sample sizes and measured bromine values in solder paste with burning aid (WO 3powder) 29 Table F.3 Additional information Difference in combustion temperatures and measured bromine values in solder paste with burning aid (WO 3powder) . 29 Table G.1 Ty

28、pical operating conditions for IC . 30 Table G.2 Example of calibration solutions for IC . 30 4 62321-3-2 IEC:2013 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DETERMINATION OF CERTAIN SUBSTANCES IN ELECTROTECHNICAL PRODUCTS Part 3-2: Screening Total bromine in polymers and electronics by Combustion

29、Ion Chromatography FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning sta

30、ndardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their prepara

31、tion is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely wi

32、th the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant sub

33、jects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technica

34、l content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent

35、possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide con

36、formity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its dir

37、ectors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arisi

38、ng out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is d

39、rawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62321-3-2 has been prepared by IEC technical committee 111: Environmental standar

40、dization for electrical and electronic products and systems. The first edition of IEC 62321:2008 was a stand alone standard that included an introduction, an overview of test methods, a mechanical sample preparation as well as various test method clauses. This first edition of IEC 62321-3-2 introduc

41、es a new clause in the IEC 62321 series. Future parts in the IEC 62321 series will gradually replace the corresponding clauses in IEC 62321:2008. Until such time as all parts are published, however, IEC 62321:2008 remains valid for those clauses not yet re-published as a separate part. 62321-3-2 IEC

42、:2013 5 The text of this standard is based on the following documents: FDIS Report on voting 111/300/FDIS 111/310/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance wi

43、th the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62321 series can be found on the IEC website under the general title: Determination of certain substances in electrotechnical products. The committee has decided that the contents of this publication will remain unchanged until the st

44、ability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 62321-3-2 IEC:2013 INTRODUCTION The widespread use of electrotechnical

45、products has drawn increased attention to their impact on the environment. In many countries all over the world this has resulted in the adaptation of regulations affecting wastes, substances and energy use of electrotechnical products. The use of certain substances (e.g. lead (Pb), cadmium (Cd) and

46、 polybrominated diphenyl ethers (PBDEs) in electrotechnical products, is a source of concern in current and proposed regional legislation. The purpose of the IEC 62321 series is therefore to provide test methods that will allow the electrotechnical industry to determine the levels of certain substan

47、ces of concern in electrotechnical products on a consistent global basis. WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibil

48、ity of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions 62321-3-2 IEC:2013 7 DETERMINATION OF CERTAIN SUBSTANCES IN ELECTROTECHNICAL PRODUCTS Part 3-2: Screening Total bromine in polymers and electronics by Combustion Ion

49、Chromatography 1 Scope Part 3-2 of IEC 62321 specifies the screening analysis of the total bromine (Br) in homogeneous materials found in polymers and electronics by using the analytical technique of combustion ion chromatography (C-IC). This test method has been evaluated for ABS (acrylonitrile butadiene styrene), EMC (epoxy molding compound), and PE (polyethylene)