IEC 61158-3-18-2007 Industrial communication networks - Fieldbus specifications - Part 3-18 Data-link layer service definition - Type 18 elements《工业通讯网络.数据总线规范.第3-18部分 数据联络层设备定义.18型元件》.pdf

《IEC 61158-3-18-2007 Industrial communication networks - Fieldbus specifications - Part 3-18 Data-link layer service definition - Type 18 elements《工业通讯网络.数据总线规范.第3-18部分 数据联络层设备定义.18型元件》.pdf》由会员分享，可在线阅读，更多相关《IEC 61158-3-18-2007 Industrial communication networks - Fieldbus specifications - Part 3-18 Data-link layer service definition - Type 18 elements《工业通讯网络.数据总线规范.第3-18部分 数据联络层设备定义.18型元件》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61158-3-18 Edition 1.0 2007-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Fieldbus specifications Part 3-18: Data-link layer service definition Type 18 elements Rseaux de communications industriels Spcifications des bus de terrain Partie 3-18: Dfinition du ser

2、vice de la couche de liaison de donnes Elments de Type 18 IEC 61158-3-18:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electr

3、onic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please co

4、ntact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y co

5、mpris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Com

6、it national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and

7、 publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been publi

8、shed. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - websto

9、re.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more tha

10、n 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assis

11、tance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes.

12、A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance v

13、ous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publicati

14、ons de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en an

15、glais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions conta

16、ctez-nous: csciec.ch. IEC 61158-3-18 Edition 1.0 2007-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial communication networks Fieldbus specifications Part 3-18: Data-link layer service definition Type 18 elements Rseaux de communications industriels Spcifications des bus de terrain Partie 3

17、-18: Dfinition du service de la couche de liaison de donnes Elments de Type 18 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 25.040.40; 35.100.20 PRICE CODE CODE PRIX ISBN 978-2-8322-0986-8 Registered trademark of the International Electrotechnical Commis

18、sion Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61158-3-18 IEC:2007 CONTENTS FOREWORD . 4 INTROD

19、UCTION . 6 1 Scope . 7 1.1 Overview . 7 1.2 Specifications 7 1.3 Conformance . 7 2 Normative references . 8 3 Terms, definitions, symbols, abbreviations and conventions . 8 3.1 Reference model terms and definitions 8 3.2 Service convention terms and definitions . 9 3.3 Data-link service terms and de

20、finitions 10 3.4 Common symbols and abbreviations . 13 3.5 Conventions 13 4 Data link services . 15 4.1 Overview . 15 4.2 Primitives of the DLS . 15 4.3 CYCLIC-DATA-UPDATE . 15 4.4 ACYCLIC-DATA-TRANSMIT 16 4.5 MASTER-TRANSMISSION-TRIGGER. 17 5 DL-management Services . 17 5.1 Overview . 17 5.2 Requir

21、ed services . 17 5.3 ESTABLISH-MASTER-POLLED 17 5.4 ESTABLISH-SLAVE-POLLED . 18 5.5 ESTABLISH-MASTER-PACKED 19 5.6 ESTABLISH-SLAVE-PACKED 19 5.7 RELEASE-CONNECTION 20 5.8 SUSPEND-CONNECTION . 20 5.9 RESUME-CONNECTION . 20 5.10 ACTIVATE-STANDBY-MASTER 21 5.11 ERROR . 21 Bibliography 23 Table 1 DLE st

22、ation identifiers . 15 Table 2 CYCLIC-DATA-UPDATE parameters 15 Table 3 ACYCLIC-DATA-TRANSMIT parameters 16 Table 4 ESTABLISH-MASTER-POLLED parameters . 18 Table 5 Baud rate parameter values 18 Table 6 ESTABLISH-SLAVE-POLLED parameters 18 Table 7 ESTABLISH-MASTER-PACKED parameters . 19 Table 8 Baud

23、rate parameter values 19 Table 9 Bit width parameter values 19 Table 10 ESTABLISH-SLAVE-PACKED parameters 20 Table 11 RELEASE-CONNECTION parameters . 20 Table 12 SUSPEND-CONNECTION parameters . 20 61158-3-18 IEC:2007 3 Table 13 RESUME-CONNECTION parameters 21 Table 14 ERROR parameters 21 4 61158-3-1

24、8 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 3-18: Data-link layer service definition Type 18 elements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising a

25、ll national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, T

26、echnical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory

27、work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations

28、. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recom

29、mendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by an

30、y end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional pub

31、lication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication

32、. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for

33、 costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct ap

34、plication of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. NOTE Use of some of the associated protocol types is restric

35、ted by their intellectual-property-right holders. In all cases, the commitment to limited release of intellectual-property-rights made by the holders of those rights permits a particular data-link layer protocol type to be used with physical layer and application layer protocols in type combinations

36、 as specified explicitly in the IEC 61784 series. Use of the various protocol types in other combinations may require permission of their respective intellectual-property-right holders. International Standard IEC 61158-3-18 has been prepared by subcommittee 65C: Industrial networks, of IEC technical

37、 committee 65: Industrial-process measurement, control and automation. This first edition and its companion parts of the IEC 61158-3 subseries cancel and replace IEC 61158-3:2003. This edition of this part constitutes a technical addition. This edition includes the following significant changes with

38、 respect to the previous edition: a) deletion of the former Type 6 fieldbus, and the placeholder for a Type 5 fieldbus data-link layer, for lack of market relevance; b) addition of new types of fieldbuses; 61158-3-18 IEC:2007 5 c) division of this part into multiple parts numbered 3-1, 3-2, , 3-19.

39、This bilingual version (2013-07) corresponds to the monolingual English version, published in 2007-12. The text of this standard is based on the following documents: FDIS Report on voting 65C/473/FDIS 65C/484/RVD Full information on the voting for the approval of this standard can be found in the re

40、port on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance resul

41、t date indicated on the IEC web site under http:/webstore.iec.ch in the data related to the specific publication. At this date, the publication will be: reconfirmed; withdrawn; replaced by a revised edition, or amended. NOTE The revision of this standard will be synchronized with the other parts of

42、the IEC 61158 series. The list of all the parts of the IEC 61158 series, under the general title Industrial communication networks Fieldbus specifications, can be found on the IEC web site. 6 61158-3-18 IEC:2007 INTRODUCTION This part of IEC 61158 is one of a series produced to facilitate the interc

43、onnection of automation system components. It is related to other standards in the set as defined by the “three-layer” fieldbus reference model described in IEC/TR 61158-1. Throughout the set of fieldbus standards, the term “service” refers to the abstract capability provided by one layer of the OSI

44、 Basic Reference Model to the layer immediately above. Thus, the data-link layer service defined in this standard is a conceptual architectural service, independent of administrative and implementation divisions. 61158-3-18 IEC:2007 7 INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 3-

45、18: Data-link layer service definition Type 18 elements 1 Scope 1.1 Overview This standard provides common elements for basic time-critical and non-time-critical messaging communications between devices in an automation environment and material specific to Type 18 fieldbus. The term “time-critical”

46、is used to represent the presence of a time-window, within which one or more specified actions are required to be completed with some defined level of certainty. Failure to complete specified actions within the time window risks failure of the applications requesting the actions, with attendant risk

47、 to equipment, plant and possibly human life. This standard defines in an abstract way the externally visible service provided by the Type 18 fieldbus data-link layer in terms of a) the primitive actions and events of the service; b) the parameters associated with each primitive action and event, an

48、d the form which they take; and c) the interrelationship between these actions and events, and their valid sequences. This standard defines the services provided to the Type 18 fieldbus application layer at the boundary between the application and data- link layers of the fieldbus reference model, a

49、nd system management at the boundary between the data-link layer and systems management of the fieldbus reference model. 1.2 Specifications The principal objective of this standard is to specify the characteristics of conceptual data-link layer services suitable for time-critical communications, and thus supplement the OSI Basic Reference Model in guiding the development of data-link