IEC 61156-5-2-2002 Multicore and symmetrical pair quad cables for digital communications - Part 5-2 Symmetrical pair quad cables with transmission characteristics up to 600 MHz Hor.pdf

《IEC 61156-5-2-2002 Multicore and symmetrical pair quad cables for digital communications - Part 5-2 Symmetrical pair quad cables with transmission characteristics up to 600 MHz Hor.pdf》由会员分享，可在线阅读，更多相关《IEC 61156-5-2-2002 Multicore and symmetrical pair quad cables for digital communications - Part 5-2 Symmetrical pair quad cables with transmission characteristics up to 600 MHz Hor.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD IEC 61156-5-2 First edition 2002-05 Multicore and symmetrical pair/quad cables for digital communications Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz Horizontal floor wiring Capability approval Sectional specification Cbles multicondu

2、cteurs paires symtriques et quartes pour transmissions numriques Partie 5-2: Cbles paires symtriques et quartes avec caractristiques de transmission allant jusqu 600 MHz Cble capillaire Agrment de savoir-faire Spcification intermdiaire Reference number IEC 61156-5-2:2002(E)Publication numbering As f

3、rom 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respecti

4、vely, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects

5、 current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technica

6、l committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/catlg-e.htm) enables you to search by a variety of criteria

7、 including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/JP.htm) is also avail

8、able by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22

9、919 03 00INTERNATIONAL STANDARD IEC 61156-5-2 First edition 2002-05 Multicore and symmetrical pair/quad cables for digital communications Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz Horizontal floor wiring Capability approval Sectional specification Cbles m

10、ulticonducteurs paires symtriques et quartes pour transmissions numriques Partie 5-2: Cbles paires symtriques et quartes avec caractristiques de transmission allant jusqu 600 MHz Cble capillaire Agrment de savoir-faire Spcification intermdiaire IEC 2002 Copyright - all rights reserved No part of thi

11、s publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone

12、: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch D For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 61156-5-2 IEC:2002(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MULTICORE AND SYMME

13、TRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz Horizontal floor wiring Capability Approval Sectional specification FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization fo

14、r standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IE

15、C publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate

16、 in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible,

17、an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specificati

18、ons, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standa

19、rds. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of i

20、ts standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61156-5-2 has been prepared by subcommi

21、ttee 46C: Wires and symmetric cables, of IEC technical committee 46: Cables, wires, waveguides, RF connectors and accessories for communication and signalling. The text of this standard is based on the following documents: FDIS Report on voting 46C/506/FDIS 46C/521/RVD Full information on the voting

22、 for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until 2006. At this date, t

23、he publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended.61156-5-2 IEC:2002(E) 3 MULTICORE AND SYMMETRICAL PAIR/QUAD CABLES FOR DIGITAL COMMUNICATIONS Part 5-2: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz Horizontal floor wiring Capabi

24、lity Approval Sectional specification 1 General 1.1 Scope This part of IEC 61156 applies to Capability Approval requirements for cables for digital communications in horizontal floor wiring in accordance with generic specification IEC 61156-1-1 and Clause 4 of the sectional specification IEC 61156-5

25、. Clause 2 refers to the content of the Capability Manual. Clause 3 refers to the Quality Plans. Clause 4 is related to the maintenance of the Capability Approval. NOTE Quality assessment belongs to the negotiation between customers and manufacturers. The following clauses are intended to be a guide

26、 when there is a request for a third-party Capability Approval. However, it may also be used as the basis for second-party or self-certification. 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition

27、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61156-1, Multicore and symmetrical pair/quad cables for digital communications Part 1: Generic specification IEC 61156-1-1, Multicore and symmetrical pair/quad cables for dig

28、ital communications Part 1-1: Capability approval Generic specification IEC 61156-5, Multicore and symmetrical pair/quad cables for digital communications Part 5: Symmetrical pair/quad cables with transmission characteristics up to 600 MHz Horizontal floor wiring Sectional specification 2 Contents o

29、f the Capability Manual 2.1 Description of the cable families related to the capability domain This subclause of the Capability Manual describes the family/families of cables for which Capability Approval is required as follows. a) Reference to the applicable standards (e.g. sectional specification,

30、 detail specifications, etc.). b) Description of the cable constructional details, for example size of conductors, insulation material and insulation dimensions, type of cable element, i.e. pairs or quads, screening material and dimensions, screen construction, sheath material and dimensions, outer

31、diameter, maximum cable size and maximum cable length. c) Additional characteristics or requirements not covered by the applicable standard. 4 61156-5-2 IEC:2002(E) 2.2 Identification of the manufacturing process, equipment utilization and manufacturing instructions For each family of cables the man

32、ufacturing processes shall be identified; for instance, by means of a flow chart as given in Annex A. For each manufacturing phase, it is required to specify: a) description of available machinery and corresponding working instructions; b) construction techniques; c) process boundaries related to ea

33、ch phase of manufacturing; d) test and inspection points in the manufacturing process. An example of such manufacturing process step identification is given in Annex B. 2.3 Policy on rework and repair This subclause describes the permissible operations of rework and repair and their related operativ

34、e instructions. 3 Quality Plan 3.1 General Reference is made to 2.2.4 of IEC 61156-1-1 with regard to process control. As a minimum, the following items shall be identified and considered: a) identification of manufacturing stages; b) identification of those characteristics which depend upon process

35、 phases and related tests; c) identification of all testing procedures; d) acceptance limits and criteria for the process and manufacturing stages; e) sampling and sampling plan (type and frequency). An example of such a sampling plan is given in Annex C. 3.2 Selection of Capability Qualifying Compo

36、nents (CQCs) It is necessary to point out that the manufacture of cables is composed of many process phases that are continuous and not independent of each other. Hence, the products in each phase are not discrete production components. For this reason, the CQCs are presented by representative sampl

37、es taken from each phase or from the finished products. NOTE It is recommended that the trend of the results and/or statistical quality indices related to the tests carried out be examined. 3.3 Purchased raw materials The Quality Plan shall include a list of the raw materials used for the manufactur

38、e of a cable family, their corresponding purchasing specifications, and procedures for incoming inspections. 3.4 Design criteria (if applicable) The Quality Plan shall include a list of the documentation concerning the design of the cable family either directly or by reference to the manufacturers i

39、nternal instructional documents.61156-5-2 IEC:2002(E) 5 The main items are a) the design of each product family; b) the material selection criteria; c) rules for the dimensioning of the cable elements. 4 Maintenance of Capability Approval The maintenance of the Capability Approval shall be based on

40、the examination of a) the documentation related to the process control carried out during the period considered; b) the test results on the finished products; c) the review of the manufacturing lines in accordance with the Capability Manual. 6 61156-5-2 IEC:2002(E) Annex A (informative) Manufacturin

41、g flow chart of the manufacturing process, equipment utilization and manufacturing instructions 1234567 8 Extrusion Twisting Laying-up Sheathing and screening Finished product Packaging E F D C B A Incoming material or finished product inspection points Test/inspection points Manufacturing phases 1

42、2 3 4 5 6 7 8 Conductor Insulation material Colouring material Core wrap Binder tapes Screening tape Drain wire (tinned) Sheathing material Key IEC 1158/0261156-5-2 IEC:2002(E) 7 Annex B (informative) Family: Symmetrical pair/quad cables for horizontal floor wiring with transmission characteristics

43、up to 250 MHz Example of identification of the manufacturing process and its boundaries Phase No. Process Process line Working instruction Process boundaries 1 Insulating Extruder XXXXX XXXX XXXX XXXXX XXXX Copper solid conductor : Min./Max. diameter Insulation thickness and diameter over the insula

44、tion Type of insulation Colour marking 2 Twisting Twisting lines XXXXX XXXX XXXXX XXXX Pairs and/or quads Minimum lay length Maximum lay length 3 Laying-up XXXXX XXXX XXXXX XXXX Pairs and/or quads Minimum lay length Maximum lay length 4 Screening Taping line XXXXX XXXX XXXXX XXXX Longitudinal minimu

45、m overlap/ Helical minimum overlap 5 Sheathing Extruder XXXXX XXXX XXXXX XXXX Type of material Min./Max. outer diameter Min./Max. thickness 6 Final tests Testing department Some tests may be performed externally 7 Packaging Delivery department Maximum cable length Maximum reel dimensions 8 61156-5-2

46、 IEC:2002(E) Annex C (informative) Family: Symmetrical pair/quad cables for horizontal floor wiring with transmission characteristics up to 250 MHz Example of Quality Plan Phase No. a Manufacturing process phase Tests Process phase characteristics Type of CQCs Frequency 1a Copper wire drawing Diamet

47、er Elongation Resistance Torsion/UTS/UTE Geometry Regularity Capacitance Integrity Insulated wires on the reel 1b Insulation Diameter Elongation Insulation resistance Spark testing Geometry Regularity Capacitance Integrity Insulated wires on the reel 2 Twisting Lay length Spark testing Unbalances Fl

48、exibility Crosstalk Integrity (Transmission parameter) Pairs on the reel 3 Laying-up Lay length Diameter Spark testing Unbalances Flexibility Crosstalk (Transmission parameter) Stranded pairs on the reel 4 Screening Overlap Continuity EMI protection Screened stranded pairs 5 Sheathing Diameter Thick

49、ness Spark testing Visual inspection Geometry Integrity Sheathed cables 6 Final tests Visual/dimensional inspection Impedance Attenuation NEXT, FEXT RL Fire behaviour Material characteristics Compliance to the performances Finished cable length Cable sample Material sample 7 Packaging Visual inspection Cable delivery Finished cable reels, packaging a The phases 1a-1b-2-3-4-5 could be