IEC 60095-4-2008 Lead-acid starter batteries - Part 4 Dimensions of batteries for heavy vehicles《铅酸起动器蓄电池组.第4部分 重型车用蓄电池组的尺寸》.pdf

《IEC 60095-4-2008 Lead-acid starter batteries - Part 4 Dimensions of batteries for heavy vehicles《铅酸起动器蓄电池组.第4部分 重型车用蓄电池组的尺寸》.pdf》由会员分享，可在线阅读，更多相关《IEC 60095-4-2008 Lead-acid starter batteries - Part 4 Dimensions of batteries for heavy vehicles《铅酸起动器蓄电池组.第4部分 重型车用蓄电池组的尺寸》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60095-4 Edition 2.0 2008-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Lead-acid starter batteries Part 4: Dimensions of batteries for heavy vehicles Batteries daccumulateurs de dmarrage au plomb Partie 4: Dimensions des batteries pour poids lourds IEC 60095-4:2008 THIS PUBLICATION IS COPYRIGH

2、T PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or

3、 IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de rep

4、roduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays

5、du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Swi

6、tzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content

7、of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (refer

8、ence number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line

9、and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocab

10、ulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Com

11、mission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est const

12、amment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (

13、numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles public

14、ations parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additio

15、nnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email

16、: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60095-4 Edition 2.0 2008-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Lead-acid starter batteries Part 4: Dimensions of batteries for heavy vehicles Batteries daccumulateurs de dmarrage au plomb Partie 4: Dimensions des batteries pour poi

17、ds lourds INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE Q ICS 29.220.20; 43.040.10 PRICE CODE CODE PRIX ISBN 2-8318-9621-5 2 60095-4 IEC:2008 CONTENTS FOREWORD.3 1 Scope and object5 2 Normative references .5 3 Terms and definitions .5 4 Common features .5 4.1 L

18、abelling .5 4.2 Marking of polarity.6 4.3 Marking of plastic material.6 4.4 Dimensions and design .7 5 European types 7 5.1 General .7 5.2 Dimensions .7 6 North American types .10 6.1 General .10 6.2 Dimensions .10 7 East Asian types.13 7.1 General .13 7.2 Dimensions .15 Bibliography17 Figure 1 Mark

19、ing of polarity .6 Figure 2 Marking of polypropylene .6 Figure 3 Dimensions ( mm) of positive and negative terminals .8 Figure 4 EU series Type D2 9 Figure 5 EU series Types A,B,C9 Figure 6 AM series Type 4D11 Figure 7 Dimensions ( mm) of tapered terminal11 Figure 8 AM series Type 8D12 Figure 9 AM s

20、eries Type 31T 12 Figure 10 Dimensions of stud terminal .13 Figure 11 AM series Type 31A 13 Figure 12 Dimensions (mm) of tapered terminal.14 Figure 13 AS series Type E 4115 Figure 14 AS series Types F51, G51 and H52.16 Table 1 EU series Dimensions of batteries8 Table 2 AM series Dimensions of batter

21、ies .10 Table 3 Dimensions of tapered terminal .14 Table 4 AS series Dimensions of batteries 15 60095-4 IEC:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LEAD-ACID STARTER BATTERIES Part 4: Dimensions of batteries for heavy vehicles FOREWORD 1) The International Electrotechnical Commission (IEC

22、) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition

23、 to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

24、in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with co

25、nditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC N

26、ational Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the

27、 way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any

28、IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users shoul

29、d ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damag

30、e of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of t

31、he referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights

32、. International Standard IEC 60095-4 has been prepared by IEC technical committee 21: Secondary cells and batteries. This second edition cancels and replaces the first edition published in 1989 and its Amendment 1 (1996).It constitutes a technical revision. The main technical changes in this new edi

33、tion relate to the reduction of the number of European battery types, the standardization of dimensions and locations of battery terminals and the updating and inclusion in the standard of Amendment 1(1996), related to North America withdrawn; replaced by a revised edition, or amended. 60095-4 IEC:2

34、008 5 LEAD-ACID STARTER BATTERIES Part 4: Dimensions of batteries for heavy vehicles 1 Scope and object This part of IEC 60095 is applicable to lead-acid batteries used for starting, lighting and ignition of heavy trucks, commercial vehicles, busses and agricultural trucks. The object of the present

35、 standard is to specify global requirements of the main dimensions of starter batteries for Europe, North America and East Asia. This International Standard comprises 12 types of “preferred types“ of batteries. The standard specifies dimensions of 4 types of batteries each for the Europe (types A, B

36、, C and D2), North America (4D, 8D, 31T, 31A) and East Asia (E41, F51, G51, H52) regions. For future new developments of heavy vehicles it is strongly recommended to use only batteries from this standard. Several other types of batteries exist under the standards of national or regional organisation

37、s. They are not included in this International Standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (incl

38、uding any amendments) applies. IEC 60050-482:2004, International Electrotechnical Vocabulary Part 482: Primary and secondary cells and batteries IEC 60095-1, Lead-acid starter batteries Part 1: General requirements and methods of test IEC 60417, Graphical symbols for use on equipment ISO 1043-1, Pla

39、stics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics ISO 7000, Graphical symbols for use on equipment Index and synopsis 3 Terms and definitions For the purposes of this document, the definitions contained in IEC 60050-482 apply. 4 Common features 4.1 Labellin

40、g The batteries shall be marked in accordance with IEC 60095-1. 6 60095-4 IEC:2008 4.2 Marking of polarity The batteries shall carry the marking of polarity, at least of the positive terminal. 4.2.1 Marking of positive terminals This marking shall take the form of the symbol + either on the upper su

41、rface of the positive terminal or on the lid adjacent to the positive terminal. 4.2.2 Marking of negative terminals If the negative polarity is also marked, the marking shall take the form of the symbol , either on the upper surface of the negative terminal or on the lid adjacent to the negative ter

42、minal. NOTE As an alternative, the wording “POS” and “NEG” is permitted for the North American market only. 4.2.3 Design and dimensions of marking The symbols used for marking the terminals shall be in accordance with symbol IEC 60417- 5005 (2002-10) for the positive and symbol IEC 60417-5006 (2002-

43、10) for the negative polarity. Suggested dimensions are shown in Figure 1. 10 10 10 2 2 IEC 221/08 Permissible are 0,3 mm 0,5 mm, indented or relief. Figure 1 Marking of polarity 4.3 Marking of plastic material Batteries are universally marked to identify the plastic material. Various marking scheme

44、s exist around the world in line with local regulations. However all schemes identify the plastic material by embossing or indenting it into the battery housing. The material content shall be in accordance with ISO 1043-1. ”PP/PE“ or ”PP“ is used as the marking for types of plastic materials. Some m

45、aterials also include the recycling symbol (ISO 7000-1135) as shown in Figure 2. Figure 2 Marking of polypropylene60095-4 IEC:2008 7 Producers are encouraged to consult the regulations of the target market. It is permissible to use the number coding 7 or 07 for PP/PE and the addition of “other“ to c

46、over additives to the plastic material. 4.4 Dimensions and design All dimensions are in millimetres. Details of the design that are not indicated in the generic drawings have to be chosen appropriately. The illustrations in this standard, especially those of the design of the lids, handles, ribs, le

47、dges, vent caps and their locations are not mandatory. 5 European types 5.1 General This applies to the series of lead-acid starter batteries for heavy trucks, widely and predominantly being used in Europe. In the text which follows, the series will be designated “EU”. The EU series comprises four t

48、ypes. 5.1.1 Fastening All types are intended for fastening by the upper part of the battery only. This fastening shall be effected at a level defined by the dimension “h 1 ” in the figures. The configuration shall permit the fitting of an angle-iron frame, both legs of which are 20 mm wide, for the

49、major part of the lids four sides. 5.1.2 Terminal configurations, polarity The terminal configuration and polarity shall be as shown in Figures 4 and 5. 5.1.3 Terminal dimensions The dimensions are shown in Figure 3. 5.2 Dimensions The main dimensions are represented by symbols, as indicated in Figures 4 and 5. The dimensions according to the symbols shall be in