UL SUBJECT 1358-2015 UL Outline of Investigation for Compressed Gas Check Valves and Hose Couplers (Issue 3)《压缩气体止回阀和软管接头的UL调查大纲 (议题3)》.pdf

《UL SUBJECT 1358-2015 UL Outline of Investigation for Compressed Gas Check Valves and Hose Couplers (Issue 3)《压缩气体止回阀和软管接头的UL调查大纲 (议题3)》.pdf》由会员分享，可在线阅读，更多相关《UL SUBJECT 1358-2015 UL Outline of Investigation for Compressed Gas Check Valves and Hose Couplers (Issue 3)《压缩气体止回阀和软管接头的UL调查大纲 (议题3)》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULAPRIL 3, 20151UL 1358Outline of Investigation for Compressed Gas Check Valves and HoseCouplersIssue Number: 3April 3, 2015Summary of TopicsThis third issue of the Outline of Investigation for Com

2、pressed Gas CheckValves and Hose Couplers, UL 1358, revises the Moist Ammonia AirStress Cracking Test.ULs Outlines of Investigation are copyrighted by UL. Neither a printed norelectronic copy of an Outline of Investigation should be altered in any way. All ofULs Outlines of Investigation and all cop

3、yrights, ownerships, and rights regardingthose Outlines of Investigation shall remain the sole and exclusive property of UL.COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULAPRIL 3, 2015UL 13582No Te

4、xt on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULCONTENTSINTRODUCTION1 Scope .42 General 42.1 Components .42.2 Units of measurement .52.3 Undated references .53 Glossary .54 Pressure and Temperature Ratings .6CONSTRUCTION5 Genera

5、l 66 Bodies .77 Materials .78 Springs 9PERFORMANCE9 General 910 Deformation Test .1011 External Leakage Test 1112 Seat Leakage Test 1113 Endurance Test 1114 Hydrostatic-Pressure Test .1215 Accelerated Aging Test 1216 Oxygen Compatibility Test .1217 Fuel Gas Compatibility Test 1318 Moist Ammonia Air

6、Stress Cracking Test 1319 Accelerated Hydrogen-Pressure Aging Test 1420 Excess Flow Check Valve Operation Test .14MANUFACTURING AND PRODUCTION TESTS21 General .15MARKING22 General 15APRIL 3, 2015 UL 1358 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSI

7、ON FROM ULINTRODUCTION1 Scope1.1 These requirements cover backpressure and other types of check valves and hose couplers forcompressed gases other than for liquefied petroleum gas (LP-Gas) in applications covered by NFPA 58,or anhydrous ammonia.1.2 Check valves and hose couplers covered by these req

8、uirements are intended for use with industrialequipment and systems such as, but not limited to, oxygen-fuel gas welding applications covered by thefollowing installation codes:a) Standard for the Design and Installation of Oxygen-Fuel Gas Systems for Welding, Cuttingand Allied Processes, NFPA 51 an

9、db) Safety in Welding and Cutting and Allied Processes, AWS Z49.1.1.3 Check valves for use with liquefied petroleum gas in applications covered by NFPA 58 or anhydrousammonia applications covered by ANSI K61.1 are covered by the requirements in the Standard for Valvesfor Anhydrous Ammonia and LP-Gas

10、 (Other Than Safety Relief), UL 125.1.4 These requirements do not apply to check valves for compressed gases for use in refrigeratedstorage systems.1.5 Except for such observations as are required to ascertain performance characteristics, the assigningof flow capacity ratings are not within the scop

11、e of these requirements.2 General2.1 Components2.1.1 Except as indicated in 2.1.2, a component of a product covered by this outline shall comply with therequirements for that component.2.1.2 A component is not required to comply with a specific requirements that:a) Involves a feature or characterist

12、ic not required in the application of the component in theproduct covered by this outline, orb) Is superseded by a requirement in this outline.2.1.3 A component shall be used in accordance with its rating established for the intended conditions ofuse.2.1.4 Specific components are incomplete in const

13、ruction features or restricted in performancecapabilities. Such components are intended for use only under limited conditions, such as certaintemperatures not exceeding specified limits, and shall be used only under those specific conditions.APRIL 3, 2015UL 13584UL COPYRIGHTED MATERIAL NOT AUTHORIZE

14、D FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2.2 Units of measurement2.2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory orapproximate information.2.3 Undated references2.3.1 Any undated reference to a code or standard appearing i

15、n the requirements of this outline shall beinterpreted as referring to the latest edition of that code or standard.3 Glossary3.1 For the purposes of this outline, the following definitions apply.3.2 CHECK VALVE, BACKPRESSURE A device that permits fluid flow in only one direction.3.3 CHECK VALVE, EXC

16、ESS FLOW A device designed to close when fluid flow exceeds aprescribed flow rate.3.4 COMPRESSED GAS IN SOLUTION (ACETYLENE) A nonliquefied compressed gas that isdissolved in a solvent.3.5 FUEL GAS Acetylene, hydrogen, natural gas, liquefied petroleum gas (LP-Gas),methylacetylene-propadiene stabiliz

17、ed gas (MPS-Gas), and methane, and other liquefied and non-liquefied flammable gases, not including biofuels, that are stable because of their composition orbecause of the conditions of storage.3.6 HOSE COUPLER A device that consists of two parts (plug and socket) that provides a meansfor manually c

18、onnecting and disconnecting the gas supply equipment to and from the gas consumingequipment, without the use of tools. The socket contains a check valve that prevents the flow of gaswhen the two parts are separated.3.7 LIQUEFIED COMPRESSED GAS A gas, which under the charged pressure is partially liq

19、uid at atemperature of 70.0F (21.1C).3.8 LIQUEFIED PETROLEUM GAS (LP-GAS OR LPG) Any material having a vapor pressure notexceeding that allowed for commercial propane composed predominantly of the following hydrocarbons,either by themselves (except propylene) or as mixtures: propane, propylene, buta

20、ne (normal butane orisobutane) and butylenes.3.9 MPS-GAS Methylacetylene-propadiene, stabilized; a mixture of gases that, in the liquid phaseconforms to the following:a) Methylacetylene-propadiene (in combination, with a maximum ratio of 3.0 moles ofmethylacetylene per mole of propadiene in the init

21、ial liquid phase in a storage container) 68mole percent maximum;b) Propane, butane, isobutane (in combination) 24 mole percent minimum of which at least1/3 (8 mole percent of total mixture) shall be butane and/or isobutane;c) Propylene 10 mole percent maximum; andd) Butadiene 2 mole percent maximum.

22、APRIL 3, 2015 UL 1358 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3.10 NONLIQUEFIED COMPRESSED GAS A gas, other than a gas in solution, which under thecharged pressure is entirely gaseous at a temperature of 70.0F (21.1C).4 Pressure and T

23、emperature Ratings4.1 The maximum pressure rating of a device for acetylene shall be 15 psig.4.2 The maximum pressure rating of a device for oxygen and fuel gases other than acetylene shall bespecified by the manufacturer.4.3 If a device is to be marked with the term Fuel Gas and not the specific fu

24、el gas(es), the device shallbe suitable for all gases specified in 3.5. The maximum pressure for these gases, other than acetylene,shall be the same.4.4 Devices covered by these requirements shall have a minimum ambient temperature rating range ofminus 20 plus 125F (minus 29 plus 52C). A device is p

25、ermitted to have a temperature range thatexceeds this maximum temperature or includes a temperature less than this minimum, but the range shallnot begin at a temperature greater than this minimum temperature or end at a temperature less than thismaximum temperature.CONSTRUCTION5 General5.1 A check v

26、alve and hose coupler shall include all of the components required for its normal functionand installation, and shall be furnished as a single unit or assembly.5.2 When a check valve or hose coupler is of a design that requires the use of special gaskets, or otherspecial fittings or parts for making

27、 a proper installation, such parts shall be furnished by the manufacturerwith each device.5.3 A seat disc shall be attached to its poppet or holder, or otherwise assembled so as to prevent it frombecoming dislocated under service conditions. The means to secure the disc shall not rely on cement orad

28、hesive.5.4 A backpressure check valve or hose coupler shall not be equipped with a bypass or other means toprevent it from closing completely.5.5 An excess flow check valve shall be provided with a means to allow for equalization of pressure afterthe excess flow valve closes. If a bypass opening is

29、used, the area of the opening shall not exceed thatof a No. 60 size drill 0.040 inch (1.02 mm) diameter.5.6 A hose coupler that is for use with a fuel gas or oxygen shall incorporate a check valve in the socketportion (supply side) of the coupler that shall close and prevent flow of gas when the two

30、 parts areseparated. When the two parts of the coupler are connected together, the design is permitted to allow flowof gas in both directions.APRIL 3, 2015UL 13586UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL6 Bodies6.1 A threaded section o

31、f a body shall be constructed with a section to serve as a wrench grip.6.2 Pipe threads shall be in accordance with the Standard for Pipe Threads, ANSI/ASME B1-20.1.Exception: Check Valves intended for use in installations where pipe fittings incorporate other than NPTtype threads shall be permitted

32、 to be provided with pipe threads complying with a national pipe threadstandard compatible with those fittings. The pipe thread type shall be identified in accordance with 22.3.6.3 Joints in a body constructed of two or more parts shall be prevented from loosening as the result ofthe turning effort

33、exerted by connecting or disconnecting piping. See the Deformation Test, Section 10.6.4 If the device is for use with welding equipment, its inlet and outlet connections shall be threaded andconform to the Standard Connections for Regulator Outlets, Torches and Fitted Hose for Welding andCutting Equ

34、ipment, CGA Pamphlet E-1; right hand threads for oxygen, left hand threads for fuel gases.Exception: Other threaded connections may be used if the threads conform to a nationally recognizedstandard and noninterchangeability between oxygen and fuel gases is maintained and the device isintended for su

35、ch application.6.5 A device shall not terminate in a hose barb type of connection unless the connection is factoryinstalled to a hose to make an assembly.6.6 Openings for bolts or screws used for assembly shall not extend through the outer walls of a bodyinto a fluid-handling section.6.7 When warpin

36、g of a casting affects the tightness of fluid-confining joints or the required fit of parts, thecasting shall be stress-relieved to reduce the risk of warping.7 Materials7.1 An operating or gas-confining part of a valve shall have the strength and durability to provide reliableservice of the part an

37、d of the assembly.7.2 To comply with the requirement of 7.1, a material for gas-confining parts of a device intended for fuelgases shall have a minimum melting point (solidus temperature) of not less than 1500F (816C). Amaterial for gas-confining parts of non-fuel gases shall have a melting point (s

38、olidus temperature) of notless than 950F (510C) and a tensile strength of not less than 10,000 psi (68.9 MPa) at 400F (204C).Exception: A valve disc, soft seat, seal ring, diaphragm, or gasket is not required to comply with thisrequirement.7.3 A part in contact with the fluid(s) to be handled shall

39、be resistant to the action of such fluid(s).7.4 With reference to the requirement in 7.3, the tests are based upon the temperature range of 4.4.Elastomeric and polymeric materials, other than for oxygen service greater than 150 psig (1.0 MPa), shallbe subjected to:a) The Accelerated Aging Test, Sect

40、ion 16;b) The Fuel Gas Compatibility Test, Section 18; andAPRIL 3, 2015 UL 1358 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULc) Hydrogen Pressure Aging Test, Section 22, if for hydrogen service, including mixtures, with amaximum pressure r

41、ating greater than 75 psig.If a device has a temperature range greater than the range in 4.4, gasket and seal material componentsshall be subjected to oven aging conditioning (time and temperature values) and low temperatureexposure conditioning, as appropriate, in accordance with the Standard for G

42、askets and Seals, UL 157for the minimum and maximum temperatures specified by the manufacturer. Test temperatures arepermitted to be interpolated for temperature ratings between test temperatures specified in UL 157.Exception: Acetal polymers, chlorotrifluorethylene polymers, tetrafluorethylene, flu

43、orinated ethylenepropylene polymers and polyamides of composition polyhexamethylene adipamide or polycaproamidepolymers (nylon 6, 6/6 or 6/16) shall only be subjected to the Accelerated Aging Test, Section 15.7.5 Elastomeric and polymeric materials utilized in the gas stream of a device intended for

44、 use withoxygen at a pressure greater than 150 psig (1.0 MPa) shall be subjected to the Oxygen Compatibility Test,Section 16.Exception: Chlorotrifluorethylene polymers, tetrafluoroethylene, fluorinated ethylene propylene polymersand polyamides of composition polyhexamethylene adipamide or polycaproa

45、mide polymers (Nylon 6 or6/16) are suitable without test.7.6 Copper or a copper alloy exceeding 67 percent copper shall not be used for a part in contact withacetylene or MPS-Gas.7.7 When corrosion of a part interferes with the proper function of a valve, the part shall be of acorrosion-resistant ma

46、terial or be provided with a corrosion-resistant protective coating, in accordancewith 7.8.7.8 Cadmium plating shall have a thickness of no less than 0.0003 inch (0.008 mm), and zinc plating shallhave a thickness of no less than 0.0005 inch (0.013 mm).Exception: On parts where threads constitute the

47、 major portion of the area, the thickness of the cadmiumor zinc plating shall be no less than 0.00015 inch (0.0038 mm).7.9 A part made of drawn brass or machined from brass rod containing more than 15 percent zinc shallbe capable of withstanding, without cracking, the Moist Ammonia Air Stress Cracki

48、ng Test, Section 18, forcopper and copper alloys.7.10 Nonductile cast iron (regular gray iron) shall not be used for bodies or closures for fuel gas checkvalves or hose couplers. This does not prohibit the use of nodular iron.7.11 Aluminum or aluminum alloys shall not be used for parts in contact wi

49、th oxygen or oxygen enrichedgases, where the percentage of oxygen exceeds 21 percent by volume, for devices having a pressurerating greater than 435 psig (3.0 MPa).7.12 Metals used in combination shall be galvanically compatible. Aluminum shall not be used incombination with copper or copper alloy.APRIL 3, 2015UL 13588UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL7.13 A brazing material used for joining liquid-confining parts of a valve shall have a melting point (solidustemper