SSPC PA 2-2015 Procedure for Determining Conformance to Dry Coating Thickness Requirements.pdf

《SSPC PA 2-2015 Procedure for Determining Conformance to Dry Coating Thickness Requirements.pdf》由会员分享，可在线阅读，更多相关《SSPC PA 2-2015 Procedure for Determining Conformance to Dry Coating Thickness Requirements.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、SSPC-PA 2January 26, 20151SSPC: The Society for Protective CoatingsPaint Application Standard No. 2Procedure for Determining Conformance to Dry Coating Thickness Requirements1. SCOPE1.1 This standard describes a procedure for determining shop or field conformance to a specified coating dry film thic

2、kness (DFT) range on ferrous and non-ferrous metal substrates using nondestructive coating thickness gages (magnetic and eddy current) described in ASTM D7091.11.2 The procedures for adjustment and measurement acquisition for two types of gages: “magnetic pull-off” (Type 1) and “electronic” (Type 2)

3、 are described in ASTM D7091.1.3 This standard defines a procedure to determine whether coatings conform to the minimum and the maximum thickness specified. See Note 12.1 for an example of a possible modification when measuring dry film thickness on overcoated surfaces. 1.4 This document contains th

4、e following non-mandatory appendices:Appendix 1 - Numerical Example of Average Thickness Measurement and Illustration of the Procedure for Determining the Magnitude of a Nonconforming AreaAppendix 2 - Methods for Measuring Dry Film Thickness on Steel Beams (Girders)Appendix 3 - Methods for Measuring

5、 Dry Film Thickness for a Laydown of Beams, Structural Steel, and Miscellaneous Parts after Shop CoatingAppendix 4 - Method for Measuring Dry Film Thickness on Coated Steel Test PanelsAppendix 5 - Method for Measuring Dry Film Thickness of Thin Coatings on Coated Steel Test Panels that Have Been Abr

6、asive Blast CleanedAppendix 6 Method for Measuring the Dry Film Thickness of Coatings on EdgesAppendix 7 Method for Measuring Dry Film Thickness on Coated Steel Pipe ExteriorAppendix 8 Examples of the Adjustment of Type 2 Gages Using ShimsAppendix 9 Precaution Regarding Use of the Standard for Coati

7、ng Failure Investigations1 ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959. For referenced ASTM standards visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standards volume information, or to review the scop

8、e of an ASTM standard, refer to the standards Document Summary page on the ASTM website.1.5 This standard is not intended to be used for measurement of thermal spray coatings. The thickness measurement procedures for thermal spray coatings applied over steel substrates are described in SSPC-CS 23.00

9、/AWS C2.23M/NACE No. 12. 2. REFERENCED STANDARDS2.1 The latest issue, revision, or amendment of the referenced standards in effect on the date of invitation to bid shall govern unless otherwise specified. Standards marked with an asterisk (*) are referenced only in the Notes, which are not requireme

10、nts of this standard.2.2 If there is a conflict between the requirements of any of the cited reference standards and this standard, the requirements of this standard shall prevail.2.3 ASTM International ASTM D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic

11、Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals (mandatory document)2.4 SSPC: The Society for Protective Coatings* PA Guide 11 Protecting Edges, Crevices, and Irregular Steel Surfaces by Stripe Coating 3. DEFINITIONS3.1 Gage Reading: A single

12、instrument reading.3.2 Spot Measurement: The average of three, or at least three gage readings made within a 4-cm (approximately 1.5-inch) diameter circle. Discussion: Acquisition of more than three gage readings within a spot is permitted. Any unusually high or low gage readings that are not repeat

13、ed consistently are discarded. The average of the acceptable gage readings is the spot measurement.SSPC-PA 2January 26, 201523.3 Area Measurement: The average of five spot measurements obtained over each 10 m2(100 ft2) area of coated surface, or portion thereof.3.4 Certified Standards: Coated or pla

14、ted metal plates (containing an uncoated plate for zero reference) with assigned values traceable to a national metrology institution. Also, uncoated shims of flat plastic sheet with assigned values traceable to a national metrology institution.4. DESCRIPTION OF GAGES4.1 Gage Types: The gage type is

15、 determined by the operating principle employed in measuring the thickness and is not determined by the mode of data readout, i.e. digital or analog. 4.2 Type 1 Magnetic Pull-Off Gages: For magnetic pull-off gages, a permanent magnet is brought into direct contact with the coated surface. The force

16、necessary to pull the magnet from the surface is measured and interpreted as the coating thickness value on an analog dial (scale) on the gage. Less force is required to remove the magnet from a thick coating. The gage scale is non-linear.4.3 Type 2 Electronic Gages: An electronic gage uses electron

17、ic circuitry to convert a reference signal into coating thickness.5. Calibration, Verification of Accuracy and Adjustment5.1 ASTM D 7091 describes three operational steps necessary to ensure accurate coating thickness measurement: calibration, verification of accuracy and adjustment of coating thick

18、ness measuring gages, as well as proper methods for obtaining coating thickness measurements on both ferrous and non-ferrous metal substrates. These steps shall be completed before taking coating thickness measurements to determine conformance to a specified coating thickness range. Verification of

19、accuracy shall be performed using certified standards. Type 2 gage adjustment to compensate for characteristics including (but not limited to) substrate metallurgy, geometry, thickness/thinness and roughness shall be performed using certified shims. The measured shims commonly supplied with Type 2 g

20、ages are also acceptable for gage adjustment.5.2 Gages shall be calibrated by the equipment manufacturer, their authorized agent or an accredited calibration laboratory. A test certificate or other documentation showing traceability to a national metrology institution is required . There is no stand

21、ard time interval for re-calibration, nor is one absolutely required. Calibration intervals are usually established based upon experience and the work environment, or when specified. A one-year calibration interval is a typical starting point suggested by gage manufacturers.5.3 To guard against meas

22、uring with an inaccurate gage, gage accuracy shall be verified at a minimum of the beginning and end of each work shift according to the procedures described in ASTM D 7091. The user is advised to verify gage accuracy during measurement acquisition (e.g., hourly) when a large number of measurements

23、are being obtained. If the gage is dropped or suspected of giving erroneous readings during the work shift, its accuracy shall be rechecked.5.4 Record the serial number of the gage, the reference standard used, the stated thickness of the reference standard as well as the measured thickness value ob

24、tained, and the method used to verify gage accuracy. If the same gage, reference standard, and method of verification are used throughout a job, they need to be recorded only once. The stated value of the standard and the measured value must be recorded each time accuracy is verified.5.5 If the gage

25、 fails the post-measurement accuracy verification check, all measurements acquired since the last accuracy verification check are suspect. In the event of physical damage, wear, or high usage, or after an established calibration interval, the gage shall be rechecked for accuracy of measurement. If t

26、he gage is not measuring accurately, it shall not be used until it is repaired and/or recalibrated (usually by the gage manufacturer).5.6 A Type 1 gage that does not meet the manufacturers stated accuracy (when verified on certified standards) cannot be adjusted to correct for the out-of-tolerance c

27、ondition and shall not be used until it is repaired and/or re-calibrated (typically by the gage manufacturer). Any manual adjustment of these gages will limit the DFT range for which the gage will provide accurate readings; therefore, adjustment of the gage is not permitted. Furthermore, the applica

28、tion of a single “correction value” representing the full range of the gage to compensate for a gage that is not measuring accurately is not appropriate, since the gage scale is non-linear. 6. MEASUREMENT PROCEDURE - TYPE 1 GAGES6.1 Verify Type 1 gage accuracy using certified coated metal plates hav

29、ing at least one thickness value within the expected range of use. Unless explicitly approved by the gage manufacturer, certified shims of plastic or of non-magnetic metals that are acceptable for verifying the accuracy of Type 2 (electronic) gages shall not be used for verifying the accuracy of Typ

30、e 1 gages.6.2 In order to compensate for any effect of the substrate itself and surface roughness, obtain measurements from the bare, prepared substrate at a minimum of ten (10) locations (arbitrarily spaced) and calculate the average value. This value represents the effect of the substrate/surface

31、roughness on a coating thickness gage. This average value is the base metal reading (BMR). 6.3 Measure the DFT of the coating at the number of spots specified in Section 8.SSPC-PA 2January 26, 201536.4 Subtract the BMR from the gage reading to obtain the thickness of the coating.7. MEASUREMENT PROCE

32、DURE - TYPE 2 GAGES7.1 The manufacturers of Type 2 (electronic) gages prescribe different methods of adjustment to measure dry film thickness over roughened surfaces. Adjust the gage according to the manufacturers instructions using one of the methods described in ASTM D 7091 or Appendix 8 of this s

33、tandard.7.2 Measure the DFT of the coating at the number of spots specified in Section 8.8. REQUIRED NUMBER OF MEASUREMENTS FOR CONFORMANCE TO A THICKNESS SPECIFICATION8.1 Number of Measurements: Repeated gage readings, even at points close together, often differ due to small surface irregularities

34、of the coating and the substrate. Therefore, a minimum of three (3) gage readings shall be made for each spot measurement of the coating. For each new gage reading, move the probe to a new location within the 4-cm (approximately 1.5-inch) diameter circle defining the spot. Discard any unusually high

35、 or low gage readings that are not repeated consistently. The average of the acceptable gage readings is the spot measurement.8.2 Unless otherwise specified in the procurement documents (project specification), an area measurement is obtained by taking five (5) separate spot measurements (average of

36、 the gage readings described in Section 8.1) randomly spaced throughout each 10-m2(100 ft2) area to be measured and representative of the coated surface. The five spot measurements shall be made for each 10-m2(100 ft2) area as follows:8.2.1 For areas of coating not exceeding 30 m2(300 ft2) arbitrari

37、ly select and measure each 10-m2(100 ft2) area.8.2.2 For areas of coating greater than 30 m2(300 ft2) and not exceeding 100 m2(1,000 ft2), arbitrarily select and measure three 10-m2(100 ft2) areas.8.2.3 For areas of coating exceeding 100 m2(1,000 ft2), arbitrarily select and measure the first 100 m2

38、(1,000 ft2) as stated in Section 8.2.2. For each additional 100 m2(1,000 ft2) coated area (or increment thereof), arbitrarily select and measure one additional 10-m2(100 ft2) area. 8.3 Nonconforming Areas: If the coating thickness for any 10-m2(100 ft2) area is not in compliance with the contract do

39、cuments, the procedure described here shall be followed to assess the magnitude of the nonconforming thickness. 8.3.1 Determine the spot DFT at 1.5-meter (5-foot) intervals in eight equally spaced directions radiating outward from the nonconforming 10-m2(100-ft2) area.If there is no place to measure

40、 in a given direction, then no measurement in that direction is necessary. Acquire spot measurements in each direction (up to the maximum surface area coated during the work shift) until two consecutive conforming spot measurements are acquired in that direction or until no additional measurements a

41、re possible. Acceptable spot measurements are defined by the minimum and maximum values in the contract documents. No allowance is made for variant spot measurements, as is the practice when determining the area DFT. An illustration of this procedure is shown in Figure A1.2.8.3.1.1 On complex struct

42、ures or in other cases where making spot measurements at 1.5-meter (5-foot) intervals is not practical, spot measurements shall be performed on repeating structural units or elements of structural units. This method shall be used when the largest dimension of the unit is less than 3 meters (10 feet)

43、. Make spot measurements on repeating structural units or elements of structural units until two consecutive units in each direction are conforming or until there are no more units to test. 8.3.2 Non-compliant areas shall be demarcated using removable chalk or other specified marking material and do

44、cumented. All of the area within 1.5 meters (5 feet) of any non-compliant spot measurement shall be designated as non-compliant. For a given measurement direction or unit measurement, any compliant area or unit preceding a non-compliant area or unit shall be designated as suspect, and as such is sub

45、ject to re-inspection after corrective measures are performed (see Note 12.2). 8.3.3 Appendices 2 through 7 provide specifiers with optional alternatives for defining the area size as well as the number and frequency of spot measurements to include in project specifications as appropriate for the si

46、ze and shape of the item or structure to be coated. 9. CONFORMANCE TO SPECIFIED THICKNESS9.1 A minimum and a maximum thickness are normally specified for each layer of coating. If a single thickness value is specified and the coating manufacturer does not provide a recommended range of thickness, th

47、en the minimum and maximum thickness for each coating layer shall be 20% of the stated value. 9.2 Table 1 provides five thickness restriction levels. Level 1 is the most restrictive and does not allow for any deviation of spot or area measurements from the specified minimum and maximum thickness, wh

48、ile Level 5 is the least restrictive. Depending on the coating type and the prevailing service environment, the specifier selects the dry film thickness restriction level for a given project. If no restriction level is specified, then Level 3 is the default. It is possible to specify a maximum thick

49、ness threshold for Level 5 Spot or Area measurements for some generic product types and service environments.SSPC-PA 2January 26, 201549.3 For the purpose of final acceptance of the total dry film thickness, the cumulative thickness of all coating layers shall be no less than the cumulative minimum specified thickness and no greater than the cumulative maximum specified thickness.10. ReportThe following items shall be reported:10.1 The type of instrument used, including manufacturer, model number, serial number and date of calibration.10.2 The type of certi