SAE MA 1806-1990 Spring Clips and Cushion Selection for Metal Tube Support Metric《金属管支撑用弹簧夹和垫片选用指南(米制)》.pdf
《SAE MA 1806-1990 Spring Clips and Cushion Selection for Metal Tube Support Metric《金属管支撑用弹簧夹和垫片选用指南(米制)》.pdf》由会员分享,可在线阅读,更多相关《SAE MA 1806-1990 Spring Clips and Cushion Selection for Metal Tube Support Metric《金属管支撑用弹簧夹和垫片选用指南(米制)》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、AEROSPACE STANDARDMA1806Issued 1990-11Reaffirmed 2006-05Spring Clips and Cushion Selection forMetal Tube Support, MetricFSC 53401. SCOPE:1.1 Type:Spring clips (inner and outer) and associated PTFE single split cushion designed to support metric metal tubes (or inch tubes, using the inch series cushi
2、on).1.2 Application:Primarily for use in aerospace propulsion systems, and suitable for use up to the maximum limitations of the cushion (e.g., 260C max).2. APPLICABLE DOCUMENTS:The following publications form a part of this specification to the extent specified herein. The latest issue of aerospace
3、 standards (MA and AS) shall apply.2.1 SAE Publications:Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.MA3294 Clip - Spring, Tension, Outer, 5.5 mm Bolt Hole, AMS 5525, MetricMA3295 Clip - Spring, Tension, Inner, 5.5 mm Bolt Hole, AMS 5525, MetricMA3296 Cushion - Tube Clamp Su
4、pport, PTFE, MetricAS3298 Cushion - Tube Clamp Support, PTFE, InchMA3393 Clip - Spring, Tension, Outer, 6.7 mm Bolt Hole, AMS 5525, MetricMA3394 Clip - Spring, Tension, Inner, 6.7 mm Bolt Hole, AMS 5525, MetricRATIONALE This document has been reaffirmed to comply with the SAE 5-year Review policy. S
5、AE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro
6、m, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2006 SAE International All rights reserved. No part of this publication may
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEMA18061990SPRINGCLIPSANDCUSHIONSELECTIONFORMETALTUBESUPPORTMETRIC 金属管 支撑 弹簧 垫片 选用 指南 米制 PDF

链接地址:http://www.mydoc123.com/p-1027878.html