SAE AS 4307C-2015 FITTING FLARED TUBE EXTERNAL STRAIGHT THREAD FOR SEAL RING.pdf

《SAE AS 4307C-2015 FITTING FLARED TUBE EXTERNAL STRAIGHT THREAD FOR SEAL RING.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4307C-2015 FITTING FLARED TUBE EXTERNAL STRAIGHT THREAD FOR SEAL RING.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING, FLARED TUBE, EXTERNAL STRAIGHT THREAD FOR SEAL RING AS4307Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

2、recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1993-08REAFFIRMED 2001-12REVISED 201

3、5-02THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4307 SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: /4/ KSC-F-124SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisrep

4、ort is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SA

5、E invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4307C 04 .250 .4375-20UNJF 1.234 .140 .668 .678-.691 .0227 .063006 .375 .5625-18UNJF 1.328 .168 .792 .802-.815 .0345 .095608 .500 .75

6、00-16 UNJF 1.516 .162 .980 .990-1.003 .0610 .16910 .625 .8750-14UNJF 1.687 .174 1.103 1.113-1.128 .0846 .23412 .750 1.0625-12UNJ 1.922 .203 1.353 1.363-1.380 .140 .38916 1.000 1.3125-12UNJ 1.969 .186 1.603 1.613-1.630 .185 .51220 1.250 1.6250-12UNJ 2.094 .224 1.853 1.863-1.880 .279 .77424 1.500 1.87

7、50-12UNJ 2.266 .224 2.099 2.109-2.135 .362 1.00028 1.750 2.2500-12UNJ 2.547 .276 2.474 2.484-2.510 .416 1.15032 2.000 2.5000-12UNJ 2.766 .265 2.724 2.734-2.760 .485 1.340LB/EA APPROX REF CRESC .010LB/EA APPROX REF ALUMBASIC NUMBER AS4307 /14/ SIZE CODE(NOMINAL TUBE SIZE)T THREAD PER AS8879 CLASS 3AA

8、 +.000 -.063 B .030ERATIONALE CORRECTED END 1 TO STYLE “E” IN FIGURE 1. UPDATED NOTE /4/ TO DELETE “PRI” STATEMENT AND CORRECT THE NADCAP SCOPE TO AC7112, AC7112/2. FIGURE 1 - FITTING, FLARED TO EXTERNAL STRAIGHT THREAD TABLE 1 - DIMENSIONS AND WEIGHTS AEROSPACE STANDARD AS4307 SHEET 2 OF 3 REV. C F

9、ITTING, FLARED TUBE, EXTERNAL STRAIGHT THREAD FOR SEAL RING NOTES: /1/ MATERIAL: a. CODE LETTER D: TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS4112; OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. b. CODE LETTER J: 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639.

10、c. CODE LETTER K: 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648. d. CODE LETTER R: 321 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645. e. CODE LETTER S: 347 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5646. f. CODE LETTER W: TYPE 7075-T73 ALUMINUM ALLOY BAR PER AM

11、S-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. 2. HEAT TREAT: a. ALL CODE LETTERS: NONE 3. FINISH: a. MATERIAL CODE LETTER D: ANODIZE PER AMS2472 OR MIL-A-8625 TYPE II, CLASS 2, DYE BLUE AND DUPLEX SEAL PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS J, K, R, AND S; PASSIVAT

12、E PER AMS2700, TYPE 6 OR TYPE 7. c. MATERIAL CODE LETTER W: ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: KSC-F-124 JOHN F KENNEDY SPACE CENTER, NASA, SPECIFICATION FOR FITTINGS (PRESSURE CONNECTIONS), FLARED

13、 TUBE. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURERS LIST (QML) AC7112, AC7112/2 FOR SIMILAR FLARED FITTINGS. THE QML IS AVAILABLE AT www.eAuditN.

14、/5/ IDENTIFICATION: MARK PER AS478 CLASS C OR CLASS D; METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS“ AND MATERIAL CODE LETTER. b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEM

15、ARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. /6/ THE SEAL RING IS ORDERED SEPARATELY AS AN AS1097. 7. INTERPRETATION OF DRAWING PER AS4296. 8. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES ARE TO BE 125 MICROINCHES Ra. 9. BR

16、EAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 10. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. AEROSPACE STANDARD AS4307 SHEET 3 OF 3 REV. C FITTING, FLARED TUBE, EXTERNAL STRAIGHT THREAD FOR SEAL RING 11. DIMENSIONS IN INCHES UNLESS OTHERWISE SPECIFIED; TOLERANCES: LINEAR DIMENSIONS .016; A

17、NGULAR DIMENSIONS 030. 12. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 13. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. /14/ EXAMPLE OF PART NUMBER: