SAE AMS-DTL-22499 1A-1999 SHIM STOCK LAMINATED ALUMINUM ALLOY《FSC 9535铝合金层压衬垫》.pdf

《SAE AMS-DTL-22499 1A-1999 SHIM STOCK LAMINATED ALUMINUM ALLOY《FSC 9535铝合金层压衬垫》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS-DTL-22499 1A-1999 SHIM STOCK LAMINATED ALUMINUM ALLOY《FSC 9535铝合金层压衬垫》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE MATERIAL SPECIFICATIONSHIM STOCK, LAMINATED, ALUMINUM ALLOYAMS-DTL-22499/1Copyright 2012 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco

2、rding, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED1998-09 REVISED 1999-01 REAFFIRMED2012-05THI

3、RD ANGLE PROJECTIONPREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D, E, F, G, P”REV.AFEDERAL SUPPLY CLASS9535AMS-DTL-22499/1SHEET 1 OF 3REV.ASAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isen

4、tirelyvoluntary, andits applicability andsuitability foranyparticularuse,includingany patent infringementarisingtherefrom,isthesoleresponsibility oftheuser.”SAE reviews eachtechnical reportatleastevery fiveyears atwhichtimeitmay berevised,reaffirmed,stabilized,orcancelled.SAE invites yourwrittencomm

5、entsandsuggestionsSAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AMSDTL22499/1RATIONALEAMS-DTL-22499/1 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE YEAR REVIEW POLICY.NOTICETHIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILI

6、TARY SPECIFICATION MIL-DTL-22499/1B, AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-DTL-22499/1B. ANY PART NUMBERS ESTABLISHED BY T

7、HE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THESAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVID

8、E FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREME

9、NTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo repro

10、duction or networking permitted without license from IHS-,-,-AEROSPACE MATERIAL SPECIFICATIONAMS-DTL-22499/1SHEET 2 OF 3REV.ASHIM STOCK, LAMINATED, ALUMINUM ALLOYTHE REQUIREMENT FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THISSPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFI

11、CATION LISTED IN THAT ISSUE OF THEDEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS) SPECIFIED IN THESOLICITATION: MIL-DTL-22499.- BAR, METAL, FLATREQUIREMENTS1. MATERIAL: ALUMINUM ALLOY AS SPECIFIED IN PROCUREMENT DOCUMENT.2. TYPES: I - ALL LAMINATIONSII - ONE-HALF SOLID STOCKCLAS

12、SES: 1. - .002 INCH LAMINATIONS2. - .003 INCH LAMINATIONS3. PART NUMBERS: THE PART NUMBER CONSISTS OF M22499/1 THE BASIC NUMBER OF THIS SPECIFICATIONSHEET AND A DASH NUMBER TAKEN FROM TABLE 1.4. THE CHANGE BAR ( | ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER INLOCATING AREAS WHERE

13、 TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THEPREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES ACOMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE MATERIAL SPECIFICATIONAMS-DTL-22499/1SHEET 3 OF 3REV.ASHIM STOCK, LAMINATED, ALUMINUM ALLOYTABLE ICopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-