SAE AMS 5726E-2008 Steel Corrosion and Heat-Resistant Bars and Wire 15Cr - 25 5Ni - 1 2Mo - 2 1Ti - 0 006B - 0 30V 1800 (982 Solution Heat Treated and Work-Strengthened Consumable .pdf
《SAE AMS 5726E-2008 Steel Corrosion and Heat-Resistant Bars and Wire 15Cr - 25 5Ni - 1 2Mo - 2 1Ti - 0 006B - 0 30V 1800 (982 Solution Heat Treated and Work-Strengthened Consumable .pdf》由会员分享,可在线阅读,更多相关《SAE AMS 5726E-2008 Steel Corrosion and Heat-Resistant Bars and Wire 15Cr - 25 5Ni - 1 2Mo - 2 1Ti - 0 006B - 0 30V 1800 (982 Solution Heat Treated and Work-Strengthened Consumable .pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5726E AEROSPACE MATERIAL SPECIFICATION AMS5726 REV. E Issued 1977-01 Revised 2
5、008-11 Reaffirmed 2015-12 Superseding AMS5726D Steel, Corrosion and Heat-Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 F (982 C) Solution Heat Treated and Work-Strengthened Consumable Electrode Remelted 200 ksi (1379 MPa) Tensile Strength Capability (Composition simila
6、r to UNS S66286) RATIONALE AMS5726E has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE 1.1 Form This specification covers a corrosion and heat-resistant steel in the form of work-strengthened bars and wire 1-1/4 inches (31.8 mm) and under in nominal diameter or least distan
7、ce between parallel sides. 1.2 Application These products have been used typically for parts, such as fasteners, requiring room-temperature minimum tensile strength of 200 ksi (1379 MPa) after precipitation heat treatment for use up to 1000 F (538 C) and having oxidation resistance up to 1200 F (649
8、 C), but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specif
9、ic document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-60
10、6-7323 (inside USA and Canada) or 724-776-4970 (outside USA), or www.sae.org. AMS2241 Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire AMS2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other High
11、ly-Alloyed Steels, and Iron Alloys AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock AMS2750 Pyrometry AMS2806 Identification, Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Hea
12、t-Resistant Steels and Alloys 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, or www.astm.org. ASTM A 370 Mechanical Testing of Steel Products ASTM E 112 Determining Average Grain Size ASTM E 353 Chem
13、ical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or
14、by other analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Carbon Manganese Silicon Phosphorus Sulfur Chromium Nickel Molybdenum Titanium Boron Vanadium Cobalt Aluminum - - - - - 13.50 24.00 1.00 1.90 0.003 0.10 - - 0.08 2.00 1.00 0.0250.02516.00 27.00 1.50 2.35 0.010
15、0.50 1.00 0.35 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. 3.2 Melting Practice Steel shall be produced by multiple melting using consumable electrode practice in the remelt cycle. SAE INTERNATIONAL AMS5726E Page 2 of 5_ 3.3 Condition Solution heat
16、treated and suitably work-strengthened. 3.3.1 Bars shall be cold finished; round bars shall be ground or turned. 3.3.2 Coiled bars and wire shall be cold-drawn. 3.4 Heat Treatment Bars and wire, except as specified in 3.4.1, shall be solution heat treated by heating to 1800 F 25 (982 C 14), holding
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS5726E2008STEELCORROSIONANDHEATRESISTANTBARSANDWIRE15CR255NI12MO21TI0006B030V1800982SOLUTIONHEATTREATEDANDWORKSTRENGTHENEDCONSUMABLEPDF

链接地址:http://www.mydoc123.com/p-1022151.html