SAE AIR 4298-1992 Impulse Test Machine Sine Wave Equipment and Operation of《脉冲试验机的正弦波 设备和操作》.pdf

《SAE AIR 4298-1992 Impulse Test Machine Sine Wave Equipment and Operation of《脉冲试验机的正弦波 设备和操作》.pdf》由会员分享，可在线阅读，更多相关《SAE AIR 4298-1992 Impulse Test Machine Sine Wave Equipment and Operation of《脉冲试验机的正弦波 设备和操作》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACEINFORMATION REPORTAIR4298 Issued 1992-01 Reaffirmed 2014-10 Impulse Test Machine, Sine Wave, Equipment and Operation of RATIONALE AIR4298 has been reaffirmed to comply with the SAE five-year review policy. _ SAE Technical Standards Board Rules provide that: “This report is published by SAE

2、to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at l

3、east every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any for

4、m or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http

5、:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AIR4298 1. SCOPE:This SAE Aerospace Information Report (AIR) describes equivalent type equipment and operational guidelines for a standard sine wave impulse test mach

6、ine. The machine may be used for testing hydraulic tubing, fittings, hose assemblies, and similar fluid system components, if desired.The standard sine wave impulse test machine is established for the following purposes:1. A design guide for future machines being built by manufacturers and users.2.

7、As a referee in the event of conflicting data from two or more nonstandard impulse machines. Such a referee machine might be built by an impartial testing activity.2. REFERENCES:2.1 Applicable Documents:MIL-H-5606 Hydraulic Fluid, Petroleum BaseMIL-H-83282 Hydraulic Fluid, Synthetic Hydrocarbon Base

8、AS4265 Impulse Testing of Hydraulic Tubing and Fittings, S-N Curve3. DISCUSSION:3.1 General:The sine wave impulse machine consists of four basic systems integrated into one operational system.3.1.1 Hydraulic Power Circuit: This is the hydraulic system, operating at normal room temperature, that prov

9、ides the hydraulic pressure to the impulse generating system. This system has all of its critical components or circuits.3.1.2 Pressure Intensification Unit: This is the hydraulic system that provides the impulse waveform to a test manifold. This unit includes an 8 to 1 low to high pressure ratio se

10、rvodriven intensifier, a rapid response servovalve, a high pressure accumulator, and other critical components needed to adjust and control the hydraulic pressure coming to and from the unit.3.1.3 Control Circuit: This is the hydraulic to electrical system that controls the signals to the PIU (press

11、ure intensification unit) and the impulse waveform at the test manifold. A typical waveform is shown in Figure 1.FIGURE 1 - Typical Sine Wave Impulse Curve3.1.4 Environmental Control Unit: This unit consists of an environmental chamber capable of controlling the test ambient temperatures and fluid t

12、emperatures within the parameters of the test document.3.2 Schematic:The schematic for the sine wave impulse machine is shown in Figure 2.SAE INTERNATIONAL AIR4298 Page 2 of 7_ FIGURE 2 - Sine Wave Impulse Machine SchematicSAE INTERNATIONAL AIR4298 Page 3 of 7_ 3.3 Critical Components:The list of cr

13、itical components including suggested part numbers is listed in Table 1. Equivalent or better equipment may be used.3.4 Test Stand:This is the means of mounting the PIU and hydraulic power supply. The PIU should be mounted in a vertical position, high pressure end down, to reduce radial loads on the

14、 PIU seals. A typical test stand is shown in Figure 3.4. OPERATIONAL GUIDELINES:4.1 Test Operation:4.1.1 VERIFY system bleed return valve open.4.1.2 VERIFY system bleed supply valve open.4.1.3 SET oven controls to obtain specified operating temperature. Obtain stability at operating temperature cond

15、itions.4.1.4 VERIFY transducer ZERO and R-CAL setup per the transducer calibration data.NOTE: Temperature sometimes affects the transducer zero.4.1.5 START hydraulic pumping system. VERIFY system supply pressure is 500 psig 100. VERIFY system bleed pressure is 300 psig 50.4.1.6 VERIFY specimen test

16、setup has been lead and pressure checked.4.1.7 RUN servodriver set point in EXTEND direction. Intensifier should be heard hitting the bottom in the extend direction.4.1.8 RUN servodriver set point in RETRACT direction. Intensifer should be heard hitting the bottom retract direction.4.1.9 CLOSE syste

17、m bleed return valve.4.1.10 CLOSE system bleed supply valve.4.1.11 RUN system supply pressure up to a pressure valve sufficient to obtain the required run impulse pressure wave conditions.4.1.12 RUN the servodriver set point pot UP to a valve approximately midway of the pressure cycle range.SAE INTE

18、RNATIONAL AIR4298 Page 4 of 7_ TABLE 1 - List of EquipmentSAE INTERNATIONAL AIR4298 Page 5 of 7_ FIGURE 3 - Typical Test StandSAE INTERNATIONAL AIR4298 Page 6 of 7_ 4.1.13 Activate the system control system to begin cycling. Run the servodriver span pot UP until the required run pressure wave span i

19、s obtained.NOTE: The servodriver span pot can be changed to move the valve of the impulse pressure wave up or down.4.2 Test Shutdown:4.2.1 Deactivate the system control system to stop cycling.4.2.2 RUN servodriver set point pot down to zero.4.2.3 RUN servodriver span pot down to zero.4.2.4 RUN syste

20、m pressure down to 500 psig 100. VERIFY system bleed pressure is 350 psig 50.4.2.5 SHUT off hydraulic pumping system.4.2.6 OPEN system bleed return valve.4.2.7 OPEN system bleed supply valve.4.2.8 COOL oven temperature DOWN to 100 F 25.PREPARED BY SAE COMMITTEE G-3, AEROSPACE COUPLINGS, FITTINGS, HOSE AND TUBING ASSEMBLIESSAE INTERNATIONAL AIR4298 Page 7 of 7_