NAVY MIL-DTL-16377 40 B-2008 FIXTURES LIGHTING LOCKS FLUORESCENT LAMP《照明设备固定装置 锁荧光灯具》.pdf

《NAVY MIL-DTL-16377 40 B-2008 FIXTURES LIGHTING LOCKS FLUORESCENT LAMP《照明设备固定装置 锁荧光灯具》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-16377 40 B-2008 FIXTURES LIGHTING LOCKS FLUORESCENT LAMP《照明设备固定装置 锁荧光灯具》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 6250 INCH-POUND MIL-DTL-16377/40B(SH) 18 December 2008 SUPERSEDING MIL-F-16377/40A(SH) 29 July 1981 DETAIL SPECIFICATION SHEET FIXTURES, LIGHTING; LOCKS FLUORESCENT LAMP This specification is approved for use by the Naval Sea Systems Command and is available for use by all departments a

2、nd agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-16377. All dimensions in inches. For tolerances, other than specified herein, see 3.5.2 of MIL-DTL-16377. FIGURE 1. Lock assembly for one 6- or

3、8-watt T5 fluorescent lamp. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/40B(SH) 2 FIGURE 2. Lock assembly for one 15-, 17-, or 20-watt T12 fluorescent lamp. FIGURE 3. Lock assembly for one 17-watt T8 fluorescent lamp. Provided by IH

4、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/40B(SH) 3 REQUIREMENTS: DESIGN: Dimensions and configurations See figures 1, 2, and 3. Material: T5 lamp lock assembly Phosphor bronze, commercial hard. T12 lamp lock assembly Body Phosphor bronze comme

5、rcial hard; thickness: 0.020; gage: 24. Lever Phosphor bronze, spring wire; diameter: 0.072. Grommet Tubing, neoprene (40-50 durometer). Finish Zinc or nickel plate (finish is optional). T8 lamp lock assembly See figure 3. EXAMINATIONS AND TESTS: Examinations and tests shall be as specified in MIL-D

6、TL-16377 and the following: First article testing/inspection See table II. Comparison inspection See table II. Conformance inspection See MIL-DTL-16377. Inspection of product for delivery: Examination See MIL-DTL-16377. Conformance test See MIL-DTL-16377. Examination for preparation of delivery See

7、MIL-DTL-16377. GENERAL INFORMATION: Table I. Standard parts. Table II. First article tests. NOTES: 1. The locks described herein, are intended for use with the fluorescent lighting fixtures, to prevent the fluorescent lamps from becoming loose under the severe shock and vibration conditions encounte

8、red aboard Navy ships. 2. The locks specified herein, were formerly covered on NAVSHIPS Drawing 9000-S6401-73939 and MS16565. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-16377/40B(SH) 4 TABLE I. Standard parts. Name Military p/n or specif

9、ication National Stock Number (NSN) Lock assembly, 6- or 8-watt T5 fluorescent lamp M16377/40-001 6250-00-399-7039 Lock assembly, 15-, 17-, or 20-watt T12 fluorescent lamp M16377/40-002 6250-00-399-7040Lock assembly, 17-watt T8 fluorescent lamp M16377/40-003 - TABLE II. First article and comparison

10、inspection. Test Requirement paragraph Test paragraph Remarks Examination 3.13 4.5 - Shock 3.5.12 4.8.7 1/Vibration 3.5.13 4.8.8 1/NOTE:1/Lamp locks require installation in fixture for testing. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with res

11、pect to the previous issue, due to the extent of the changes. Preparing Activity: Navy SH (Project 6250-2006-002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-