NAVY MIL-C-60570 B-1992 CARTRIDGE DELAY M114 ASSEMBLY《M114型炮筒延迟发射组件》.pdf

《NAVY MIL-C-60570 B-1992 CARTRIDGE DELAY M114 ASSEMBLY《M114型炮筒延迟发射组件》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-60570 B-1992 CARTRIDGE DELAY M114 ASSEMBLY《M114型炮筒延迟发射组件》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-bO570B 13 999990b 0507573 L m I MILIT. R SPECIFIC ATiOi INCH-POUND MIL-C-60570B 15 Januarv 1992 SUPERSEDING 31 August 1971 MIL-C-60570A CARTRIDGE, DELAY, M114 ASSEMBLY his specification is approved for use by all Departments and Agencies of the Department ofDefense. 1. SCOPE 1.1 Scope. This sp

2、ecification covers the requirements for the M114 Delay Cartridge (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Government documents 2.1.1 Specifications, standards and handbooks. The following specifications and standards form a part of this document to the extent specified herein. Unless otherwise specifi

3、ed, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplements thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILITARY MIL-A-2550 Ammunition, General Specification for MIL-C-60539 Coating, Anod

4、ic, Conventional for Aluminum and Aluminum Alloy Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Standardization Branch (Code 3730)

5、, 101 Strauss Avenue, Indian Head, MD 20640-5035, by using the self addressed Standardization Document Improvement Proposal (DD Fom 1426) appearing at the end of this document or by letter. I_I AMSC N/A FSC 1377 DISTNBtJTIIQN STATEMENT A: Approved for public release; distribution is unlimited. Provi

6、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b0570B 13 M 999990b 0507574 3 4 MLC-60570B STANDARDS MILITARY MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes MIL-STD-109 Quality Assurance Terms and Definitions MIL-STD-453 Ins

7、pection, Radiographic MIL-STD-8 10 Environmental Test Methods and Engineering Guidelines (niess otherwise specified, copies of federal and military specifications and standards are available from Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 191 11-5094.) 2.

8、1.2 Other Government documents, drawings, and publications. The following Government drawings form a part of this specification to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation (see 6.2). DRAWINGS NAVAL SEA SYSTEMS COMMAND (CAGE Code 5371 1)

9、5 185050 M90 Closed Bomb Assembly (5.747 in”) NAVAL ORDNANCE STATION (CAGE Codes 19200 and 19203) DL85961 10 Cartridge, Delay, M114 Assembly 8845190 Cqon, Packing, Ammunition, For Cartridge Delay: M46, M71, M90, XM102, XM103, XM104, XM105, or M114 8845 19 1 Box, Packing, Ammunition, For Cartridge, D

10、elay: M46, M71, M90, XM102, XM103, XM104, XM105 or M114 922773 1 Carton, Alternative, Packing, Ammunition, For Cartridge, Delay: M46, M7 1, M90, XM102, XM103, XM104, XM105, or M114 (Application for copies should be addressed to: Commanding Officer, Naval Ordnance Station, Data Control Branch (Code 3

11、720), Indian Head, MD 20640-5035.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exempt

12、ion has been obtained. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i. t- MILC-60570B 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a first article sample shall be subjected to first article inspection (see

13、 4.4, 6.2 and 6.3). 3.2 Conformance to documents. The M114 Delay Cartridge covered by this specification shall be manufactured in accordance with DL85961 10 and all documents listed thereon. 3.3 Materials. All materials used in the manufacture of the cartridges shall conform strictly to the specific

14、ations referred to on the respective drawings unless specific approval in writing covering a departure therefrom has been obtained from the cognizant Navy design activity prior to manufacture. When alternate materiais or methods of manufacture are specified on the drawings, the bidders selections sh

15、all be clearly stated in the proposal. 3.4 Components. 3.4.1 Primary components. For the purpose of this specification, the M42 Primer, M13 Delay Element, Igniter Charge and the cartridge propellant charge are considered primary components. Only primary components from a single lot shall be used in

16、a production lot of cartridge; however, one primary component production lot may be used in more than one cartridge production lot. 3.4.1.1 Primer. The primer shall conform to the applicable drawing and reference specification. Only primers from lots manufactured within the last 24 months or recerti

17、fied within the last 12 months shall be used in these units. Prior to assembly into a cartridge, the primer shall be radiographically examined for defects as specified in 4.7.1. 3.4.2 Hardness. The hardness of each component part shall be in accordance with the applicable drawing (see 4.7.2). 3.4.3

18、Protective finish. The finish of each component part shall be in accordance with MIL-C- 60539 and the applicable drawing (see 4.7.3). 3.5 Assembly. 3 51 Radiographic examination. Each cartridge assembly shall be radiographically examined for defects (see 4.7.4). 3.5.2 Airtightness. Each assembled ca

19、rtridge shall exhibit no air leakage greater than 1 X l4 standard cubic centimeters per second (see 4.7.5) at a 14.7 psia pressure differential. 3.5.3 Vibration. The assembled cartridge shall withstand vibration as prescribed in MIL-STD-810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5 wit

20、hout evidence of any disintegration of the primer, propellant, or igniter, or derangement of any component (see 4.7.7 and 6.2). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-b0570B 13 m 9999906 0507576 7 m MILC-60570B 3.6 Functional require

21、ments. 3.6.1 Primer sensitivity. The primer shall fire when drop tested at an energy level of 26 inch- ounces in a sectioned cartridge void of igniter and propellant charge (see 4.7.8.1). 3.6.2 Cartridge performance. 3.6.2.1 Misfires. The cartridge shall not fail to fire. 3.6.2.2 Ballistics, The car

22、tridge, when tested in the M90 Closed Bomb (Drawing 5185050), shall produce the pressures, delay times (see 6.5. i), and times to P, (see 6.5.2) at temperatures specified in table I (see 4.7.8.2). Temperature I (“FI 65 to 75 I 195 to 205 TABLE I. Ballistic reauirements. i Pressure (psig) Delay time

23、Time to P, (s Lower upper (ms) 2.7 - 4.2 2000 2700 14 2.7 - 3.3 2000 2700 14 2.1 - 3.3 2000 2700 14 3.7 Workmanship. Cartridges shall be free of cracks, splits, or other defects which might prevent proper mating with connecting parts of proper functioning of the device. 3.7.1 Metal defects. All comp

24、onents shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.7.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.7.3 Foreign matter. No part or assemb

25、ly shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinati

26、ons and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the

27、right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements (see 6.2). 4 e Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 t-

28、 NIL-C-bO570B 13 W 9997706 0507577 9 m MIGc-60570B 4.1.1 Responsibility for compliance. Ail items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any in

29、spection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an accepta

30、ble practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 Quality assurance terms and definitions. Reference shall be made to MIL-ST

31、D-109 to defme the quality assurance terms used. 4.1.3 Inspections. Inspections shall be in accordance with MIL-A-2550 and MIL-STD-453. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4) b. Quality conforma

32、nce inspection (see 4.5) 4.3 Inspection conditions. Unless otherwise specified in the contract or purchase order (see 6.2), inspection conditions shall be as follows: a. Temperature: Room ambient 20“ to 25“ C (68“ to 77“ F) b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmosphe

33、ric: 14.7 psia 4.4 First article inspection. At the beginning of regular production, the contractor shall submit a first article sample to a Government approved facility for evaluation. The sample shall consist of 21 assembled cartridges for ballistics testing including 12 for vibration tests, 5 ass

34、embled cartridges for sealant tests, 10 sets of unassembled components for dimensional and visual examination, and the quantity specified in accordance with 4.4.2, Le., cartridges assembled without the igniter and propellant charge for primer sensitivity test. The first article sample shall be manuf

35、actured using the same materials, equipment, processes, and procedures as used in regular production. All parts and materials, including packaging and packing, shall be the same as used for regular production and shall be obtained from the same source of supply. When it becomes necessary to make a c

36、hange in either the primer, propellant, or igniter lot after initial production, 12 assembled cartridges from the first production lot thereafter shall be tested in accordance with 4.7.7. The Government reserves the right to require new first article samples until such time as an acceptable sample i

37、s submitted (see 6.3). 4.4.1 Examination, tests, and facility. After provisional acceptance at source, the sample shall be inspected for all requirements of the drawings and specifications at a Government laboratory or other such facility specified in the contract (see 6.2). 5 Provided by IHSNot for

38、 ResaleNo reproduction or networking permitted without license from IHS-,-,-, _. MIL-C-60570B 13 H 9999906 0507578 O I 4 MTLC-60570B 4.4.2 Sample size for primer sensitivity. The number of cartridges assembled without igniter or propellant to be submitted for primer sensitivity tests shall be in acc

39、ordance with table II. , TABLE II. Primer sensitivitv. 4.4.3 Temperature conditioning for ballistic test. The sample shall be temperature conditioned and tested to determine compliance with 3.6.2.2. The sample for firing shall be conditioned to table III. TABLE III. TemPerature conditioning. I I I I

40、 Temperature (OF) Not vibrated Vibrated -60 to -70 3 4 I 65 to 75 I 3 I 4 I I 195 to 205 I 3 1 4 I 4.4.4 First article failure. Failure of the sample to comply with the requirements of the drawings and specifications shall result in first article sample disapproval. 6 Provided by IHSNot for ResaleNo

41、 reproduction or networking permitted without license from IHS-,-,-I. . i- MIL-C-60570B 13 - 999990b 0507579 2 - MILC-60570B 4.5 Quality conformance inspection. 4.5.1 Lot. 4.5.1.1 Submission of product. The product shall be submitted in accordance with MIL-STD-105. 4.5.1.2 Lot size. Unless otherwise

42、 specified (see 6.2), the production lot size shall be not more than 1200. 4.5.2 Examination and tests. The quality conformance sample shall be subjected to the examinations of 4.6 and all the test procedures of 4.7 except for 4.7.7. 4.6 Examination. All cartridges and components shall be examined v

43、isually and radiographically and characteristics defined in accordance with the applicable drawings. One hundred percent examination shall be performed for all critical defects. Examination for major or minor defects shall be performed on a defect basis in accordance with the classification of defec

44、ts. Four power (4 X) magnification may be used in performing visual examination for such defects as burrs and foreign matter. When compliance is in doubt as a result of visual inspection, the characteristic shall be measured or gaged to determine acceptability. All nonconforming items shall be rejec

45、ted. 4.6.1 Cartridge, Delay M114 Assembly, Drawing 8596110. Characteristic Defect Method of Inspection Critical 1 2 Major 101 102 103 104 105 106 107 108 Minor 20 1 202 203 Any part missing Improper assembly Mixed delay elements or propellant Metal defective Crimp missing or incorrect Marking missin

46、g, incorrect or illegible X-ray/Visual X-ray/Visual Visual Visual Visual Visual Cartridge profile failure Diameter of body, max Diameter of head, max Location of datum diameter “O“ ring split, cracked or cut Protective finish inadequate or defective Foreign matter present Burr Gage Gage Gage Gage Vi

47、sual Visual Visual Visual Total length, max Case damaged Varnish inadequate or missing Gage Visual Visual 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-605708 13 9999906 0507580 9 MILC-60570B 4.6.2 Delay element, M13, Drawing 8596113, cover

48、ing a detail of Drawing 8596110. Characteristic Defect Method of Inspection Critical 1 Mixed delay elements 2 3 4 5 6 Metal defective Flash hole missing or obstructed Primer uncrimped or seal missing Marking missing, incorrect, or illegible Delay charge not visible through flash hole Major 101 102 B

49、urr 103 Foreign matter present Protective finish inadequate or defective Visual Visual Visual Visual Visual Visual Visual Visual Visual Minor None defined 4.6.3 Case, Cartridge, Drawing 8595202, Bart No. 8595393 covering a detail of Drawing 8596110. Critical 1 Metal defective Major 101 102 103 104 105 106 107 108 109 Minor 20 1 202 203 204 205 Concentricity of head with body Straightness of base Diameter of body, min Diameter of he