NAVY MIL-C-46240 A (2)-1986 CARTRIDGE THRUSTER M67A1《M67A1型助推式炮弹》.pdf

《NAVY MIL-C-46240 A (2)-1986 CARTRIDGE THRUSTER M67A1《M67A1型助推式炮弹》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-46240 A (2)-1986 CARTRIDGE THRUSTER M67A1《M67A1型助推式炮弹》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、i Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Standardization Branch (5241) , Indian Head, MD 20640-5000. Commanding Officer, Naval Ordnance Station, Q .b MI L- C- 46 240A ( OS) AMENDMENT 2

2、14 October 1986 SUPERSEDING AMENDMENT 1 5 SEPTEMBER 1967 MILITARY SPEC I FICATION CARTRIDGE , IMPULSE, M67Al This amendment forms a part of Military Specification MIL-C-46240A(MU), dated 21 July 1965, and is approved for use within the Naval Sea Systems Command, Department of the Navy, and is availa

3、ble for use by all Departments and Agencies of the Department of Defense. PAGE 1 TITLE: Delete “CARTRIDGE, THRUSTER, M67A1“ and substi tute “CARTRIDGE, IMPULSE , M67A1“ 1.1 Delete “Cartridge, Thruster, M67A1“ and substitute “Cartridge, Impul se, M67A1“ * 2.1 Delete: MIL-E-5272. . .I in its entirety.

4、 Delete: MIL-STD-639. . .I1 in its entirety. Add: “MIL-STD-810 Envi ronmental Test Methods and Engineering Guidelines“. Change the title of D8597730 from “Cartridge, Thruster, M67A1, Assembly“ to Vartridge Impul se, M67A1 , Assembly“ PAGE 2 * Add: “2.2 Other publications. The following document form

5、s a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the document which are DOD adopted shall be those AMSC N/A DISTRIBUTION STATEMENT A: Page 1 of 2 FSC 1377 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo r

6、eproduction or networking permitted without license from IHS-,-,-MI L- C- 46240A ( OS ) Amendment 2 listed in the issue of the DODISS specified in the solicitation. otherwise specified, the issues of documents not listed in the DODISS shall be the issue of the nongovernment documents which is curren

7、t on the date of the solicitation. Unless ANSI B46.1 (Application for copies should be addressed to the American National 1430 Broadway, NY 10018.) Surface Texture (Surface Roughness, Waviness and Lay) Standards Institute (ANSI) (Nongovernment standards and other pub1 ications are normally available

8、 from the organization which prepares or which distri butes the documents. These documents also may be available in or through libraries or other informational services. )li PAGE 4 * 4.3.2 Delete “The Ordnance Standard Finish Blocks prescribed in MIL-STD-639 . . .I1 and substi tute “The roughness co

9、mparison standards prescribed in ANSI-B46.1 . . . II PAGE 5 4.3.2.1.1 : Change the paragraph identi f i cati on from “Cartridge, Thruster, M67A1, Assembly, Drawing D8597730“ to Cartridge, Impulse, M67A1, Assembly, Drawing D8597730“ PAGE 8 * 4.4.3 Delete I. . MIL-E-5272, Procedure II“ and substitute

10、l. . . MIL-STD-810, Method 514.3, Test Procedure I, Test Condition 1-3.2.5“. Changes from previous issue. The margins of this specification are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a c

11、onvenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Preparing Activity: Navy - OS Project No. 1377-N836 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-