IEC 60603-7-7-2010 Connectors for electronic equipment - Part 7-7 Detail specification for 8-way shielded free and fixed connectors for data transmissions with .pdf

《IEC 60603-7-7-2010 Connectors for electronic equipment - Part 7-7 Detail specification for 8-way shielded free and fixed connectors for data transmissions with .pdf》由会员分享，可在线阅读，更多相关《IEC 60603-7-7-2010 Connectors for electronic equipment - Part 7-7 Detail specification for 8-way shielded free and fixed connectors for data transmissions with .pdf（60页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60603-7-7 Edition 3.0 2010-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Connectors for electronic equipment Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz Connecteurs pour quipements lectroniques Partie 7-7: S

2、pcification particulire pour les fiches et les embases blindes 8 voies pour la transmission de donnes des frquences jusqu 600 MHz IEC 60603-7-7:2010 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part

3、of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyrigh

4、t or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni uti

5、lise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supp

6、lmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC

7、) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest editi

8、on, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publi

9、cations. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and

10、electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on t

11、his publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des n

12、ormes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut

13、 avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications

14、retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionn

15、aire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/web

16、store/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60603-7-7 Edition 3.0 2010-05 INTERNATIONAL STAND

17、ARD NORME INTERNATIONALE Connectors for electronic equipment Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz Connecteurs pour quipements lectroniques Partie 7-7: Spcification particulire pour les fiches et les embases

18、 blindes 8 voies pour la transmission de donnes des frquences jusqu 600 MHz INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 31.220.10 PRICE CODE CODE PRIX ISBN 978-2-88910-967-8 Registered trademark of the International Electrotechnical Commission Marque dp

19、ose de la Commission Electrotechnique Internationale colour inside 2 60603-7-7 IEC:2010 CONTENTS FOREWORD.4 INTRODUCTION.6 1 General 7 1.1 Scope7 1.2 Normative references 7 2 Terms and definitions .8 3 Common features and isometric view .8 3.1 General .8 3.2 Isometric view .9 3.3 Common features9 3.

20、4 Engagement (mating) information9 3.5 Fixed connectors.10 3.6 Free connectors 12 4 Cable terminations and internal connections.14 4.1 General .14 4.1.1 Complete connectors (pairs)14 4.1.2 Switch function 15 4.2 Termination types15 5 Gauges 15 5.1 Fixed connectors.15 5.2 Free connectors 18 6 Charact

21、eristics .20 6.1 General .20 6.2 Pin and pair grouping assignment .21 6.3 Climatic category.22 6.4 Electrical characteristics22 6.5 Transmission characteristics .22 6.5.1 General .22 6.5.2 Insertion loss.23 6.5.3 Return loss23 6.5.4 Propagation delay .23 6.5.5 Delay skew23 6.5.6 NEXT 23 6.5.7 Power

22、sum NEXT (for information only) .24 6.5.8 FEXT.24 6.5.9 Power sum FEXT (for information only) .24 6.5.10 Transverse conversion loss .24 6.5.11 Transverse conversion transfer loss 24 6.6 Mechanical characteristics 25 6.6.1 Mechanical operation 25 6.6.2 Effectiveness of connector coupling devices25 6.

23、6.3 Insertion and withdrawal forces .25 7 Tests and test schedule25 7.1 General .25 7.2 Arrangement for contact resistance test: .25 7.3 Arrangement for vibration test .25 60603-7-7 IEC:2010 3 7.4 Test procedures and measuring methods 25 7.5 Preconditioning .25 7.6 Wiring and mounting of specimens 2

24、5 7.6.1 Wiring25 7.6.2 Mounting .25 7.7 Test schedules 25 7.7.1 Basic (minimum) test schedule 25 7.7.2 Full test schedule 26 Bibliography28 Figure 1 Isometric view, example of fixed and free connector, free connector shown with both switch positions .9 Figure 2 Contact interface dimensions with term

25、inated free connector .10 Figure 3 Physical interface, fixed connector, front view11 Figure 4 Physical interface, fixed connector, side view.11 Figure 5 Physical interface, free connector 13 Figure 6 Fixed connector additional go gauge16 Figure 7 Fixed connector additional no-go gauges .17 Figure 8

26、Free connector additional no-go gauges.19 Figure 9 Free connector additional go gauges20 Figure 10 Fixed connector pin and pair grouping assignment (front view of connector) 21 Figure 11 Basic switch function (Note: colours stated are an example of colours which may be used)21 Figure 12 Additional s

27、witch function (Note: colours stated are an example of colours which may be used)22 Table 1 Physical interface, contacts interface 10 Table 2 Fixed connector common dimensions12 Table 3 Common dimensions free connector.14 Table 4 Fixed connector, additional, gauge dimensions .18 Table 5 Free connect

28、or additional gauges dimensions .20 Table 6 Test group EP .26 4 60603-7-7 IEC:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR ELECTRONIC EQUIPMENT Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz FOREWO

29、RD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the elect

30、rical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to tech

31、nical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Orga

32、nization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technica

33、l committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publicat

34、ions is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their nationa

35、l and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment servic

36、es and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servan

37、ts or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication

38、, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility t

39、hat some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60603-7-7 has been prepared by subcommittee 48B: Connectors, of IEC technical committee 48: Electromechani

40、cal components and mechanical structures for electronic equipment. This third edition of IEC 60603-7-7 cancels and replaces the second edition issued in 2006, and constitutes a technical revision. The main technical changes with regard to the previous edition are as follows: Removal of test methods

41、that are now referenced to IEC 60512-26-100. Addition of TCL and TCTL requirements. Removal of the electrical, mechanical, dimensional, environmental conditioning tests by reference to IEC 60603-7. 60603-7-7 IEC:2010 5 The text of this standard is based on the following documents: FDIS Report on vot

42、ing 48B/2152/FDIS 48B/2187/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of IEC 60603 series, under the g

43、eneral title Connectors for electronic equipment, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publicatio

44、n. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users

45、 should therefore print this document using a colour printer. 6 60603-7-7 IEC:2010 INTRODUCTION IEC 60603-7 is the base specification of the whole series. Subsequent specifications do not duplicate information given in the base document, but list only additional requirements. For complete specificat

46、ion regarding a component of a higher number document all lower numbered documents shall be considered as well. The following diagram shows the interrelation of the documents: Indicates reference for transmission performance (backward compatibility) Indicates reference for dimensions, mechanical and

47、 electrical characteristics, tests and test schedules. Unshielded Shielded 3 MHz 100 MHz 250 MHz 600 MHz IEC 60603-7 IEC 60603-7-1 IEC 60603-7-3 IEC 60603-7-4 IEC 60603-7-5 IEC 60603-7-7 500 MHz IEC 60603-7-41 IEC 60603-7-51 1 000 MHz IEC 60603-7-71 IEC 60603-7-2 60603-7-7 IEC:2010 7 CONNECTORS FOR

48、ELECTRONIC EQUIPMENT Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors for data transmission with frequencies up to 600 MHz 1 General 1.1 Scope This part of IEC 60603 covers 8-way, shielded, free and fixed connectors, references dimensional, mechanical, electrical and env

49、ironmental characteristics and tests in IEC 60603-7 and IEC 60603-7-1, and specifies electrical transmission requirements for frequencies up to 600 MHz. These connectors are typically used as category 7 connectors in class F cabling systems specified in ISO/IEC 11801. These connectors are intermateable and interoperable with other IEC 60603-7 series connecto