NAVY A-A-59781-2005 LIGHT EMITTING DIODES FOR USE AS INDICATOR LIGHTS《发光二极管应用为指示灯》.pdf

《NAVY A-A-59781-2005 LIGHT EMITTING DIODES FOR USE AS INDICATOR LIGHTS《发光二极管应用为指示灯》.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-59781-2005 LIGHT EMITTING DIODES FOR USE AS INDICATOR LIGHTS《发光二极管应用为指示灯》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data that may improve this document should be sent to: Commander, Naval Sea Systems Command, ATTN: SEA 05Q, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard DC 20376-5160 or emailed to commandstandard

2、snavsea.navy.mil, with the subject line “Document Comment”. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. FSC 5980 INCH-POUND A-A-59781 25 October 2005 COMMERCIAL ITEM DESCRIPTION L

3、IGHT EMITTING DIODES FOR USE AS INDICATOR LIGHTS The General Services Administration has authorized the use of this commercial item description, for all federal agencies. 1. SCOPE. This Commercial Item Description (CID) covers the performance of solid-state light emitting diodes (LEDs) for use as in

4、dicator lights. The LEDs will provide indicator illumination in lieu of conventional incandescent indicator lamps. The form, fit and function of the LED will be comparable to the legacy incandescent lamps when being applied in retrofit applications. 2. CLASSIFICATION. The LEDs shall be designated in

5、 accordance with ANSI C79.1, MIL-DTL-3661, and MIL-DTL-6363 as specified (see 7.2). 3. SALIENT CHARACTERISTICS. 3.1 General requirements. 3.1.1 Materials. All materials used in the construction of the LED shall be suitable for a marine type environment. All metal parts of the LED shall be fabricated

6、 from corrosion-resistant materials or have a corrosion-resistant treatment. 3.1.1.1 Dissimilar metals. Contact of dissimilar metals shall be avoided. 3.1.1.2 Polarity. The LED shall be bipolar. The LED indicator shall operate whether or not the center contact is positively or negatively biased. The

7、 use of microelectronic components to achieve bipolarity is allowed so that the overall size of the LED does not exceed the dimensions of the legacy incandescent lamp the LED is replacing. 3.1.1.3 Color/chromaticity. LED colors shall be as specified (see 7.2) or in accordance with SAE-AS25050. Color

8、 matching shall be specified to match the color of the lens used with the legacy incandescent lamp. Each LED shall be provided with a colored band at the juncture of the base to lens denoting the color of the LED. Colors will be basic, solid, and permanent. Pastel coloring is not allowed. 3.1.1.4 Di

9、ffusion angle. The diffusion angle of the LED shall be 120 degrees or as specified (see 7.2) between the viewing angles of 10 through 120 degrees. 3.1.1.5 Illumination intensity. The illumination intensity of the LED shall be comparable to the incandescent indicator that the LED is replacing (see MI

10、L-DTL-3661 and MIL-DTL-6363 luminance requirements). Multiple chip LEDs are allowable to increase the intensity of an LED light source. 3.1.1.6 Power requirements. A replacement LED shall consume power equal to or less than the power of the incandescent lamp the LED is replacing. 3.1.2 Environmental

11、 conditions. The LED shall be designed for shipboard use in a marine type environment. Typical environmental tests include those tests identified in MIL-DTL-3661, MIL-DTL-6363 and MIL-STD-202. Actual environmental test requirements shall be as specified (see 7.2). Provided by IHSNot for ResaleNo rep

12、roduction or networking permitted without license from IHS-,-,-A-A-59781 23.1.2.1 Ambient temperature. The LED shall operate in an ambient temperature range of 0 F (-17.8 C) to 122 F (50 C). 3.1.2.2 Shock. When specified (see 7.2), the LED shall be designed to withstand the high impact shock tests f

13、or grade A, type A equipment in accordance with MIL-S-901. 3.1.2.3 Vibration. When specified (see 7.2), the LED shall be designed to withstand a Type I vibration test in accordance with MIL-STD-167-1. 3.1.2.4 Humidity. The LED shall be designed to operate in humidity from 0 to 100% relative. 3.1.2.5

14、 Electrostatic discharge. The LED should not be susceptible to electrostatic discharge (ESD) damage. 3.1.2.6 Salt spray (corrosion). When specified (see 7.2), salt spray tests shall be in accordance with MIL-DTL-3661 or MIL-DTL-6363. 3.1.2.7 Dimensions and tolerances. The LED dimensions shall be as

15、specified (7.2), or match the dimensions of the legacy incandescent indicators as shown in MIL-DTL-6363 specification sheets 0.002. 3.2 Performance. 3.2.1 Operating life/efficacy. The LED shall have a minimum operating life of 50,000 hours with 50% lumen maintenance factor applied and retain 80% of

16、its initial illumination levels after 30,000 hours of operation. 3.3 Maintenance. The LED shall require minimal effort for removal and replacement. 3.4 Electrical requirements. The LED shall be rated for the shipboard voltage specified (see 7.2); typical shipboard electrical power is 115-volt AC ung

17、rounded electrical service in accordance with MIL-STD-1399-300. The LED shall be designed such that the LED does not impose a ground upon the electrical power system from which it is energized. 3.4.1 Insulation resistance. The insulation resistance between all current-carrying and non-current-carryi

18、ng parts of the LED shall be at least 1 megohm withstanding up to 500 VDC. 3.5 Night vision device (NVD) compatibility. When specified (see 7.2), the LED indicator shall be compatible with Night Vision Devices (NVDs) in accordance with MIL-STD-3009, and shall not cause users of such devices to becom

19、e visually impaired when used in areas where the LED is operating. 4. REGULATORY REQUIREMENTS. 4.1 Recovered materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR).

20、4.2 Toxicity. The materials used in construction of the LED shall have no toxic effect on the health of personnel when used for its intended purpose. Smoke produced during a fire involving the LED shall have no adverse effect on the health of personnel. Questions pertinent to this effect shall be re

21、ferred by the contracting activity to the appropriate departmental medical service that will act as an advisor to the contracting activity. Regardless of any other requirements, materials and parts containing asbestos, mercury, lead, cadmium, chlorofluorocarbons (CFCs), vinyl chlorides, antimony tri

22、oxide, red phosphorous and halogenated compounds (materials that contain iodine, bromine, chlorine, and fluorine) shall not be used. The contractor shall have the toxicological product formulations and associated information of the materials available for review by the contracting activity to evalua

23、te the safety of the material for the proposed use. 4.3 Environmental protection. The item shall meet all applicable Environmental Protection Agency (EPA) restrictions in effect on the date of the contract. These regulations apply to the emission of materials hazardous to the environment or the user

24、s health and shall be adhered to during the manufacturing, service, transportation, storage, and operations/use of the item. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59781 35. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The pr

25、oducts provided shall meet the salient characteristics of this Commercial Item Description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial marketplace. The government reserves the right to

26、require proof of such conformance. 5.2 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of FED-STD-3

27、76 and all other requirements of this CID are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request shall be made to the contracting officer to determine if the product is acceptable. The contracting officer has

28、 the option of accepting or rejecting the product. 6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 Source of documents. 7.1.1 ANSI. ANSI standards are available from the American National Standards Institute, 25 W. 43rdSt, 4thFloor, New

29、York, NY 10036 or online at http:/webstore.ansi.org/. 7.1.2 FED-STDs. FED-STDs are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 7.1.3 MIL-SPECs. M

30、ilitary specifications are available at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 7.1.4 MIL-STDs. Military standards are available at http:/assist.daps.dla.mil/qui

31、cksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094. 7.1.5 SAE. SAE standards are available from SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or online at www.sae.org. 7.2 Or

32、dering data. The contract or order should specify the following: a. CID document number and revision. b. Product conformance provisions. c. Quantity required. d. Classification (see 2). e. Color/chromaticity (see 3.1.1.3). f. Diffusion angle (if different from that specified) (see 3.1.1.4). g. Envir

33、onmental testing (see 3.1.2). h. Shock testing (see 3.1.2.2). i. Vibration testing (see 3.1.2.3). j. Salt spray testing (see 3.1.2.6). k. Dimensions and tolerances (see 3.1.2.7). l. Electrical requirement, voltage rating (see 3.4). Provided by IHSNot for ResaleNo reproduction or networking permitted

34、 without license from IHS-,-,-A-A-59781 4m. NVD compatibility (see 3.5). 7.3 Key words. Chromaticity Diffusion angle Illumination intensity Incandescent indicator lamp Light emitting diode (LED) MILITARY INTERESTS CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS Custodians: Army CR Preparing Activity:

35、Navy SH Navy - SH Air Force 99 (Project 5980-0033-000) Review Activities: Army MI Navy CG, EC Air Force 11, 19 DLA CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-