FORD FLTM BN 108-02-2001 RESISTANCE TO ABRASION - TABER ABRASER (Replaces FLTM BN 008-02 FLTM EU-BN 008-2)《耐磨性能 泰伯耐磨性测定仪法 替代FLTM BN 008-02 FLTM EU-BN 008-2》.pdf

《FORD FLTM BN 108-02-2001 RESISTANCE TO ABRASION - TABER ABRASER (Replaces FLTM BN 008-02 FLTM EU-BN 008-2)《耐磨性能 泰伯耐磨性测定仪法 替代FLTM BN 008-02 FLTM EU-BN 008-2》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BN 108-02-2001 RESISTANCE TO ABRASION - TABER ABRASER (Replaces FLTM BN 008-02 FLTM EU-BN 008-2)《耐磨性能 泰伯耐磨性测定仪法 替代FLTM BN 008-02 FLTM EU-BN 008-2》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、FORD LABORATORY TEST METHOD BN 108-02Date Action Revisions2001 09 11 Revised Editorial no technical change A. Cockman1996 04 26Printed copies are uncontrolled Page 1 of 5Copyright 2001, Ford Global Technologies, Inc.RESISTANCE TO ABRASION - TABER ABRASERApplicationThis procedure is used to test the

2、abrasion resistance of textile fabrics, coated fabrics, genuine leather, cardboard, rubber floor mats, carpets, other floor covering materials, plastics and painted substrates.Apparatus RequiredAbraser*Model 140, or equivalent, which meets the requirements of ASTM D 1175. The abraser shall be equipp

3、ed with a vacuum attachment.Specimen Holder*Catalog No. E-100-125 108 mm O.D.Hold Down Ring*Catalog No. E-100-101 108 mm I.D.Rubber Pad*Catalog No. S-19.Clamp Plate*54 mm O.D. for textile fabrics, genuine leather, and coated fabrics.Clamp Plate*32 mm DO.D. for carpets and other floor covering materi

4、als.Wheel Refacer*Model 133, or equivalent.Abrasive Discs*Catalog No. S-11.FORD LABORATORY TEST METHOD BN 108-02Page 2 of 5Copyright 2001, Ford Global Technologies, Inc.Wheels*Type - Calibrade H-10 or H-18 for carpets (flocked carpets, use H-10 only), Calibrade CS-10 for all other materials unless o

5、therwise designated by the Engineering Material Specification.Date: Use prior to expiration date stamped on wheels.Hardness: None on H-10 or H-18 wheels. The hardness on CS-10 wheels shall be 76-84 when measured with a Shore Type Durometer (ASTM D 2240). Take the average of five (5) readings at equa

6、lly-spaced locations around the abrading surface of the wheel, midway between edges.Readings shall be taken 6 - 10 sec after firm contact between the presser foot and wheel.* Sources:Taber Instrument Corp. Erichsen GmbH hold the wheels by their outer edges.7. The refacing operation leaves the wheels

7、 with sharp corners that must be rounded off prior toconducting a test. This is accomplished by mounting a piece of scrap fabric on the Taber and running the wheels on the fabric while lightly holding a piece of S-11 abrasive paper against the corners. Caution: Only the extreme sharpness of the corners should be removed about 1 mm radius is sufficient. Do not round to excess.Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.