ETSI TS 101 570-4-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 4 Class E Te_1.pdf

《ETSI TS 101 570-4-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 4 Class E Te_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 101 570-4-2012 Electromagnetic compatibility and Radio spectrum Matters (ERM) Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios Part 4 Class E Te_1.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 101 570-4 V1.1.1 (2012-06) Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 4: Class E Test Descriptions Technical Specification ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)2Reference DTS/ERM-TG26-0

2、88-4 Keywords DSC, interoperability, maritime, TSS Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no inv

3、estigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Spec

4、ification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 4 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.1. ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)51 Scope The p

5、resent document contains the Test Descriptions (TD) for interoperability testing of the class E DSC radio equipment. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited versio

6、n applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included i

7、n this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI EN300 338-4: “Electromagnetic compatibility and Radio spectrum Matters (E

8、RM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service; Part 4: Class E DSC“. 2.2 Informative references The following referenced documents are not neces

9、sary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TS 101 570-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 1: Requiremen

10、ts catalogue“. i.2 ETSI EN 300 338-1: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Technical characteristics and methods of measurement for equipment for generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF, MF/HF and/or VHF mobile service;

11、 Part 1: Common requirements“. 3 Abbreviations For the purposes of the present document, the abbreviations given in EN 300 338-1 i.2 and the following apply: CF (Test) ConFiguration EUT Equipment Under Test TD Test Description TP Test Purpose TSS Test Suite Structure ETSI ETSI TS 101 570-4 V1.1.1 (2

12、012-06)64 Test Configurations This clause defines all test configurations used. Each test description refers to one or multiple test configurations. It is assumed that the initial state of all the equipment involved in the test configuration is standby, i.e. unless stated otherwise the pre-test cond

13、itions of each test description assume standby mode for the equipment. An arrow connection between devices indicates that these devices are in communication range, i.e. in CFG_6 EUT, QE1 and QE2 are all in the same communication range. However, QE3 is only in communication range with QE2. ETSI ETSI

14、TS 101 570-4 V1.1.1 (2012-06)7Figure 1: Configurations for class E EUT ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)85 Test Suite Structure (TSS) The following table shows the Test Suite Structure contained in the present document. Test Group Test Sub-Group (sub-group ID) MF/HF radio functions (MFHF) Indi

15、vidual Calls (IC) Group Calls (GC) Geographic Area Calls (GAC) Sending Distress Alerts (SDA) Receiving Distress Alerts (RDA) Sending Distress Relays and Acknowledgements (SDRA) Non-Distress Automated Procedures (NDAP) Other Calls (OC) Interface and other functions (IF) General test (GEN) Alarms in s

16、tandby mode (ASM) Alarms when busy (AWB) Standby mode interface functions (SMIF) Each test description is described through a tabular format conforming to the following convention: Interoperability Test Description Identifier: A unique identifier. The test description identifiers are conforming to t

17、he TD_DSC_ naming convention, where: is the Test Group ID (VHF / MFHF) is the Test Sub-Group ID is the sequential number within the test sub-group Summary: Short description of the test objective Configuration: The relevant test configuration, referencing the test set configurations listed in the An

18、nex References: The reference indicates the clauses of the base standard specifications in which the related interoperability requirement is expressed. Pre-test conditions: Defines in which initial state the test equipment has to be to apply the actual test description Step Test Sequence Verdict Pas

19、s Fail 1 The description of the individual condition to verify or action to perform Yes/No criteria of the outcome of this verification step (if applicable) Yes/No criteria of the outcome of this verification step (if applicable) 2 Final verdict: ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)96 Test Descri

20、ptions (TD) 6.1 Individual Calls Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0001 Summary: Sending Individual call - Routine Configuration: CF_1 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz QE1 programmed with an individual MMSI Ste

21、p Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives

22、the call Yes No 7 Verify that EUT is still on 2 182 kHz Yes No 8 Cause QE1 to send ACK to EUT 9 Verify that EUT switches to the selected channel in step 4 Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0002 Summ

23、ary: Sending Individual call with NACK - Routine Configuration: CF_1 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz QE1 programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Ent

24、er/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the individual call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT is still on 2 182 kHz Yes No 8 Cause QE1 to send NACK to EU

25、T 9 Verify that EUT does not switch to the selected channel in step 4 Yes No 10 Verify that EUT indicates unable to comply Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0003 Summary: Sending Individual call to a coast station - Routine Configuration: CF_2 Referen

26、ces: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz QE1 programmed with a Coast Station MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu does not propose a working channe

27、l Yes No Final verdict: ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)10Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0004 Summary: Receiving Individual call - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT prog

28、rammed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to 2 214 kHz 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed ch

29、annel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on 2 182 kHz Yes No 8 Cause EUT to send ACK to QE1 9 Verify that EUT switches to 2 214 kHz Yes No 10 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier:

30、 TD_DSC_MFHF_IC_0005 Summary: Receiving Individual call with NACK - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select

31、 Individual - Routine 2 Enter/select MMSI of EUT 3 Set the proposed channel to 2 214 kHz 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT displays the MMSI of QE1 Yes No 7 Verify that EUT is still on 2 182 kH

32、z Yes No 8 Cause EUT to send NACK to QE1 9 Verify that EUT is still on 2 182 kHz Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0006 Summary: Receiving Individual call when busy - Routine Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditio

33、ns: QE1 and EUT in individual call on 2 214 kHz QE2 programmed with an individual MMSI of EUT Step Test Sequence Verdict Pass Fail 1 On QE2 select Call then select Individual - Routine 2 Enter/select MMSI of EUT 3 Cause QE2 to send the individual call to EUT 4 Verify that EUT sounds a self-terminati

34、ng alarm Yes No 5 Verify that EUT is still on 2 214 kHz Yes No 6 Cause EUT to terminate the individual call 7 Verify that EUT displays that calls are on hold Yes No 8 On EUT enter the received call log and verify that the call from QE2 is logged Yes NoFinal verdict: ETSI ETSI TS 101 570-4 V1.1.1 (20

35、12-06)11Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0007 Summary: Receiving Individual call - Urgency Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT programmed with an individual MMSI Step Test Sequence Verdict

36、 Pass Fail 1 On QE1 select Call then select Individual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to 2 214 kHz 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Ye

37、s No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on 2 182 kHz Yes No 9 Cause EUT to send ACK to QE1 10 Verify that EUT switches to 2 214 kHz Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DS

38、C_MFHF_IC_0008 Summary: Receiving Individual call with NACK - Urgency Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Indiv

39、idual - Urgency 2 Enter/select MMSI of EUT 3 Set the proposed channel to 2 214 kHz 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Urgency alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Y

40、es No 8 Verify that EUT is still on 2 182 kHz Yes No 9 Cause EUT to send NACK to QE1 10 Verify that EUT returns to standby on 2 182 kHz Yes No Final verdict: ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)12Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0009 Summary: Receiving Individual call

41、- Safety Configuration: CF_2 References: 1, clauses 5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Safety 2 Enter/select MMSI of EUT 3 Set the proposed

42、channel to 2 214 kHz 4 Cause QE1 to send the individual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Safety alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on 2 182 kHz Yes No 9 Cause EU

43、T to send ACK to QE1 10 Verify that EUT switches to 2 214 kHz Yes No 11 Verify voice communication on this channel Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0010 Summary: Receiving Individual call with NACK - Safety Configuration: CF_2 References: 1, clauses

44、5.2.2 and 6.7.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz EUT programmed with an individual MMSI Step Test Sequence Verdict Pass Fail 1 On QE1 select Call then select Individual - Safety 2 Enter/select MMSI of EUT 3 Set the proposed channel to 2 214 kHz 4 Cause QE1 to send the individ

45、ual call to EUT 5 Verify that EUT receives the call and displays the proposed channel Yes No6 Verify that EUT sounds the Safety alarm Yes No 7 Verify that EUT displays the MMSI of QE1 Yes No 8 Verify that EUT is still on 2 182 kHz Yes No 9 Cause EUT to send NACK to QE1 10 Verify that EUT returns to

46、standby on 2 182 kHz Yes No Final verdict: Interoperability Test Description Identifier: TD_DSC_MFHF_IC_0011 Summary: Sending Individual call on a Distress channel Configuration: CF_2 References: 1, clauses 5.2.2 and 6.6.1 Pre-test conditions: QE1 and EUT in standby on 2 182 kHz QE1 programmed with

47、an individual MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Individual - Routine 2 Enter/select MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Enter a distress channel as working channel 5 Cause EUT to send the individual call to QE1 6 Verify that

48、EUT does not send the call and indicates a channel selection error Yes NoFinal verdict: ETSI ETSI TS 101 570-4 V1.1.1 (2012-06)136.2 Group Calls Interoperability Test Description Identifier: TD_DSC_MFHF_GC_0001 Summary: Sending group call - Routine Configuration: CF_2 References: 1, clause 6.6.1 Pre

49、-test conditions: QE1 and EUT in standby on 2 182 kHz QE1 programmed with a group MMSI Step Test Sequence Verdict Pass Fail 1 On EUT select Call then select Group 2 Enter/select group MMSI of QE1 3 Verify that menu proposes an Intership Channel Yes No 4 Verify if the proposed channel can be changed Yes No 5 Cause EUT to send the group call to QE1 6 Verify that QE1 receives the call Yes No 7 Verify that EUT switches to the selecte