EN ISO 2247-2002 en Packaging - Complete filled transport packages and unit loads - Vibration tests at fixed low frequency《包装 满载的运输包装及成组装运 固定低频率振动试验 ISO 2247-2000 代替EN 22247-1992》.pdf

《EN ISO 2247-2002 en Packaging - Complete filled transport packages and unit loads - Vibration tests at fixed low frequency《包装 满载的运输包装及成组装运 固定低频率振动试验 ISO 2247-2000 代替EN 22247-1992》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 2247-2002 en Packaging - Complete filled transport packages and unit loads - Vibration tests at fixed low frequency《包装 满载的运输包装及成组装运 固定低频率振动试验 ISO 2247-2000 代替EN 22247-1992》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 2247:2002 Packaging Complete, filled transport packages and unit loads Vibration tests at fixed low frequency The European Standard EN ISO 2247:2002 has the status of a British Standard ICS 55.180.40 BS EN ISO 2247:2002 This British Standard was published under the authori

2、ty of the Standards Policy and Strategy Committee on 28 April 2003 BSI 28 April 2003 ISBN 0 580 41627 5 National foreword This British Standard is the official English language version of EN ISO 2247:2002. It is identical with ISO 2247:2000. It supersedes BS EN 22247:1993 which is withdrawn. The UK

3、participation in its preparation was entrusted by Technical Committee PKW/1, Packaging generalities, to Subcommittee PKW/1/4, Packaging generalities Test methods, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cr

4、oss-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or o

5、f British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text;

6、present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover,

7、 an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii to iv, pages 1 to 5, the Annex ZA page, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since

8、publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO2247 September2002 ICS55.180.40 SupersedesEN22247:1992 Englishversion PackagingComplete,filledtransportpackagesandunitloads Vibrationtestsatfixedlowfrequency(ISO2247:2000) EmballagesEmballagesdexpditioncompletsetpl

9、eins etchargesunitairesEssaisdevibrationbasse frquencefixe(ISO2247:2000) VerpackungVersandfertigePa ckstckeund LadeeinheitenSchwingprfungmitniedrigerFestfrequenz (ISO2247:2000) ThisEuropeanStandardwasapprovedbyCENon26August2002. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichsti

10、pulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,Fren

11、ch,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Germany,Greece, Iceland,I

12、reland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2002CEN Allrightsofexploitationinanyformandbyanymeansreserved

13、 worldwideforCENnationalMembers. Ref.No.ENISO2247:2002EForeword ThetextoftheInternationalStandardfromTechnicalCommitteeISO/TC122“Packaging“ofthe InternationalOrganizationforStandardization(ISO)hasbeentakenoverasaEuropean StandardbyTechnicalCommitteeCEN/TC261“Packaging“,thesecretariatofwhichisheldby

14、AFNOR. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMarch2003,andconflictingnational standardsshallbewithdrawnatthelatestbyMarch2003. ThisdocumentsupersedesEN22247:1992. AccordingtotheCEN/CENELECInternalRegulations,the

15、nationalstandardsorganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedKingdom. Endorsementnotice Thetex

16、toftheInternationalStandardISO2247:2000hasbeenapprovedbyCENasa EuropeanStandardwithoutanymodifications. NOTENormativereferencestoInternationalStandardsarelistedinannexZA(normative). ENISO2247:2002Reference number ISO 2247:2000(E) INTERNATIONAL STANDARD ISO 2247 Third edition 2000-03-01 Packaging Com

17、plete, filled transport packages and unit loads Vibration tests at fixed low frequency Emballages Emballages dexpdition complets et pleins et charges unitaires Essais de vibration basse frquence fixe ENISO2247:2002ii ENISO2247:2002iii Foreword ISO (the International Organization for Standardization)

18、 is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repre

19、sented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are

20、 drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a

21、vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 2247 was prepared by Technical Committee ISO/TC 122, P

22、ackaging, Subcommittee SC 3, Performance requirements and tests for means of packaging, packages and unit loads (as required by ISO/TC 122). This third edition cancels and replaces the second edition (ISO 2247:1985), which has been technically revised. Annex A forms a normative part of this Internat

23、ional Standard. ENISO2247:2002iv Introduction It is the responsibility of the user of this International Standard to establish appropriate health and safety practice in accordance with relevant legislation. ENISO2247:2002INTEANRTIONAL TSAADNDR ISO 2:742(0002)E 1 Packaging Complete, filled transport

24、packages and unit loads Vibration tests at fixed low frequency 1 Scope This International Standard specifies methods to carry out vibration tests on complete, filled transport packages or unit loads using sinusoidal excitation at fixed frequency. These tests may be used to assess the performance of

25、packages and unit loads in terms of the strength or the protection that they offer to their contents when subjected to low frequency vibration. These tests may be performed either as a single test to investigate the effects of low frequency vibration or as a part of a sequence of tests designed to m

26、easure the ability of a package or unit load to withstand a distribution system that includes a vibration hazard at low frequency or repetitive shocks. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this Int

27、ernational Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative docume

28、nts indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 2206, Packaging Complete, filled transport packages Identification of parts when testing. ISO 2233,

29、 Packaging Complete, filled transport packages and unit loads Conditioning for testing. ISO 2234, Packaging Complete, filled transport packages and unit loads Stacking tests using static load. 3 Term and definition For the purposes of this International Standard, the following term and definition ap

30、plies. 3.1 test specimen a complete, filled transport package or unit load 4 Principle The test specimen is placed on a vibration table and subjected to a vibration using an approximately sinusoidal excitation at a fixed low frequency. The atmospheric conditions, the duration of the test, the peak a

31、cceleration, the attitude of the test specimen and any method of restraint are predetermined. NOTE When required, a load may be superimposed on the test specimen to simulate conditions at the bottom of a stack. ENISO2247:20022 5 Apparatus 5.1 Vibration equipment, meeting the following requirements:

32、a) capable of operating at a fixed peak to peak vertical component displacement and operational frequency within the range selected from Figure A.1 (see normative annex A). A rotary movement of the table is allowed; b) of sufficient size and performance, in terms of power, displacement, frequency ra

33、nge and stiffness. Its lowest resonant frequency shall be higher than the highest test frequency. It shall be horizontal within a maximum angular deviation of 0,3. NOTE The table may be equipped with: 1) low fences to restrict sideways and endways movements during testing; 2) high fences or other me

34、ans of maintaining a superimposed load in position on the test specimen during testing; 3) means to simulate the method of restraining the test specimen during transit. 5.2 Instrumentation, if required, meeting the following requirements: a) comprising accelerometers, signal conditioners and data di

35、splay or storage devices to measure and control the accelerations at the test surface; b) having an acceleration response accurate to within 5 % over the frequency range specified for the test. 6 Test specimen preparation and conditioning 6.1 Preparation Fill the test specimen with its intended cont

36、ents and ensure that the test specimen is closed normally, as if ready for distribution. NOTE Simulated or substitute contents may be used provided that the dimensions and physical properties of such contents are as close as possible to those of the intended contents. The normal method of closure sh

37、ould still be used. 6.2 Conditioning The test specimen shall be conditioned in accordance with one of the conditions described in ISO 2233. 7 Procedure 7.1 Common procedure for methods A and B 7.1.1 Wherever possible, the test shall be carried out in atmospheric conditions identical to those used fo

38、r conditioning, particularly where this is critical to the materials or application of the test specimen. In other circumstances, the test shall be carried out in atmospheric conditions which approximate those used for conditioning as closely as is practicable. 7.1.2 Place the test specimen in the p

39、redetermined attitude on the vibration table (see 5.1), with the centre of its lowest face or its centre of gravity placed as near as practicable to the centre of the table; if the test specimen is not secured to the table it may be fenced. 7.1.3 If a superimposed load is required, the loading proce

40、dure shall comply with ISO 2234. 7.1.4 Subject the test specimen to vibration according to either method A (see 7.2) or method B (see 7.3). ENISO2247:20023 7.2 Method A 7.2.1 Operate the vibration table to give an acceleration at a selected level between 0,5 g and 1,0 g with the test specimen not se

41、parating from the table. 7.2.2 Perform the test at a peak to peak displacement selected from Figure A.1 of annex A, at a fixed frequency within the appropriate frequency range, to produce a test acceleration between 0,5 g and 1,0 g. 7.3 Method B 7.3.1 Operate the vibration table to give an accelerat

42、ion at a selected level such that the test specimen separates from the table causing repetitive shocks. 7.3.2 Select the desired vibration amplitude, start vibration of the test specimen at a frequency of 2 Hz and slowly increase it until the test specimen repeatedly separates from the vibration tab

43、le. NOTE 1 Separation of the test specimen from the vibration table may be determined by inserting a 1,5 mm to 3,0 mm thick spacer, with a minimum width of 50 mm, under at least 1/3 of the base area of the test specimen. This may be done by moving the spacer along the base of the test specimen durin

44、g the test. NOTE 2 The results of the test may be influenced by the thickness of the spacer. 8 Test report The test report shall include: a) a reference to this International Standard; b) the name and address of the testing laboratory and the name and address of the customer; c) the unique identific

45、ation of the report; d) the date of receipt of the test specimens and the date(s) of performance of the test; e) the name, title and signature of persons accepting test responsibility for the test report; f) a statement to the effect that the test results relate only to the specimens tested; g) a st

46、atement that the report shall not be reproduced except in full without the written approval of the testing laboratory; h) the number of replicate test specimens tested; i) a full description, including dimensions, structural and material specifications of the test specimen and its fittings, cushioni

47、ng, blocking, closure and reinforcing arrangements, gross mass of the test specimen and mass of the contents in kilograms; j) a description of the contents and if simulated or substituted contents were used, full details shall be given; k) the relative humidity, the temperature and time of condition

48、ing, the temperature and relative humidity of the test area at the time of the test, whether these values comply with the requirements of ISO 2233; l) the method used (A and/or B); m) the attitudes in which the test specimen was tested, using the method of identification specified in ISO 2206; ENISO2247:20024 n) the vertical motion of the table, whether linear,