EN 62061-2005 en Safety of machinery C Functional safety of safety-related electrical electronic and programmable electronic control systems (Incorporating Corrigendum February 201.pdf

《EN 62061-2005 en Safety of machinery C Functional safety of safety-related electrical electronic and programmable electronic control systems (Incorporating Corrigendum February 201.pdf》由会员分享，可在线阅读，更多相关《EN 62061-2005 en Safety of machinery C Functional safety of safety-related electrical electronic and programmable electronic control systems (Incorporating Corrigendum February 201.pdf（102页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 62061:2005corrigenda July 2005,April 2008 and February 2010Safety of machinery Functional safety of safety-related electrical, electronic and programmable electronic control systemsICS 13.110; 25.040.99; 29.020Incorporating BS EN +A1:2013Incorporating corrigenda July 2005, Apri

2、l 2008 and February 2010BS EN +A2:2015EUROPEAN STANDARD EN 62061NORME EUROPENNE EUROPISCHE NORM April 2005CENELECEuropean Committee for Electrotechnical StandardizationComit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart

3、 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 62061:2005 E ICS 13.110; 25.040.99; 29.020 Incorporates corrigendum February 2010English versionSafety of machinery Functional safety of safety-related ele

4、ctrical, electronic and programmable electronic control systems(IEC 62061:2005)Scurit des machines Scurit fonctionnelle des systmes de commande lectriques, lectroniques et lectroniques programmables relatifs la scurit(CEI 62061:2005)Sicherheit von Maschinen Funktionale Sicherheit sicherheitsbezogene

5、r elektrischer,elektronischer und programmierbarerelektronischer Steuerungssysteme(IEC 62061:2005)This European Standard was approved by CENELEC on 2004-12-01. CENELEC members are bound tocomply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standar

6、d the status of a national standard without any alteration.Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French,

7、 German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria, Belgium, Cypr

8、us, CzechRepublic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,Switzerland and United Kingdom.EN 62061:2005+A1February 2013BS EN 62061:2005+A2:2015I

9、SBN 978 0 580 88106 0Amendments/corrigenda issued since publicationAmd. No. Date Comments15929 Corrigendum No. 1July 2006 Implementation of IEC corrigendum July 200528 February 2009 Implementation of IEC corrigendum April 200831 May 2010 Implementation of CENELEC corrigendum February 2010. Replaceme

10、nt of EC Directive 98/37/EC with 2006/42/EC and deletion of the second dashed item in Annex ZZ30 June 2013 Implementation of IEC amendment 1:2012 with CENELEC endorsement A1:2013: Annex ZA and ZZ updated31 October 2015 Implementation of IEC amendment 2:2015 with CENELEC endorsement A2:2015: Annex ZA

11、 updatedThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 April 2005 The British Standards Institution 2015. Published by BSI Standards Limited 2015National forewordThis British Standard is the UK implementation of EN 62061:2005+A2:2015, inc

12、orporating corrigendum February 2010. It is identical to IEC 62061:2005, incorporating amendments 1:2012 and 2:2015, and corrigenda July 2005 and April 2008. It supersedes BS EN 62061:2005+A1:2013, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the

13、 text by tags. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by A1 tags The start and finish of text introduced or altered by corrigendum is indicated in the text by tags. Text altered by IEC corrigendum July 2005

14、 is indicated in the text by , and text altered by IEC corrigendum April 2008 is indicated in the text by .The UK participation in its preparation was entrusted to Technical Committee MCE/3, Safeguarding of machinery.A list of organizations represented on this committee can be obtained on request to

15、 its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.EUROPEAN STANDARD EN 62061NORME EUROPENNE EUROPISCHE NORM April 2

16、005 CENELECEuropean Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2005 CENELEC - All rights of exploitation in any form and by any means reserv

17、ed worldwide for CENELEC members. Ref. No. EN 62061:2005 E ICS 13.110; 25.040.99; 29.020 Incorporates corrigendum February 2010English version Safety of machinery Functional safety of safety-related electrical, electronic and programmable electronic control systems (IEC 62061:2005)Scurit des machine

18、s Scurit fonctionnelle des systmes de commande lectriques, lectroniques et lectroniques programmables relatifs la scurit (CEI 62061:2005) Sicherheit von Maschinen Funktionale Sicherheit sicherheitsbezogener elektrischer, elektronischer und programmierbarer elektronischer Steuerungssysteme (IEC 62061

19、:2005) This European Standard was approved by CENELEC on 2004-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra

20、phical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of

21、 a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland

22、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 62061:2005+A1February 2013EN 62061:2005+A2August 2015Foreword The text of document 44/460/FDIS, future edition 1 of IEC 62061, prepared

23、 by IEC TC 44, Safety of machinery - Electrotechnical aspects, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62061 on 2004-12-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical nati

24、onal standard or by endorsement (dop) 2005-11-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-12-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and

25、covers essential requirements of EC Directive 98/37/EC. See Annex ZZ. PROOF TEST INTERVAL AND LIFETIME The following important information should be noted in relation to the requirements of this standard: Where the probability of dangerous failure per hour (PFHD) is highly dependent upon proof testi

26、ng (i.e. tests intended to reveal faults not detected by diagnostic functions) then the proof test interval needs to be shown as realistic and practicable in the context of the expected use of the safety-related electrical control system (SRECS) (e.g. proof test intervals of less than 10 years can b

27、e unreasonably short for many machinery applications). CEN/TC114/WG6 have used a proof test interval (mission time) of 20 years to support the estimation of mean time to dangerous failure (MTTFD) for the realization of designated architectures in Annex B of prEN ISO 13849-1. Therefore, it is recomme

28、nded that SRECS designers endeavour to use a 20 year proof test interval. It is acknowledged that some subsystems and/or subsystem elements (e.g. electro-mechanical components with high duty cycles) will require replacement within the SRECS proof test interval. Proof testing involves detailed and co

29、mprehensive checks that can, in practice, only be performed when the SRECS and/or its subsystems has been designed to facilitate proof testing (e.g. dedicated test ports) and provided with necessary information (e.g. proof test instructions). To ensure the validity of the proof test interval specifi

30、ed by the designer it is important that any other necessary designated tests (e.g. functional tests) are also successfully performed at the SRECS. Annexes ZA and ZZ have been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 62061:2005 was approved by CENELEC as a Eur

31、opean Standard without any modification. _ The contents of the corrigendum of February 2010 have been included in this copy. BS EN 62061:2005Page 2Page 2BS EN 62061:2005+A1:2013EN 62061:2005+A1:2013EC Directive 2006/42/EC. See Annex ZZ.Page 3BS EN 62061:2005+A1:2013EN 62061:2005+A1:2013EN 62061:2005

32、/A1:2013 - 2 - Foreword The text of document 44/655/CDV, future edition 1 of IEC 62061:2005/A1, prepared by IEC TC 44 “Safety of machinery - Electrotechnical aspects“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62061:2005/A1:2013. The following dates are fixed: lates

33、t date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-09-18 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-12-18 Attention is drawn to the possibili

34、ty that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 62061:2005/A1:2012 was approved by CENELEC as a European St

35、andard without any modification. Foreword to amendment A1BS EN 62061:2005+A2:2015EN 62061:2005+A2:2015EN 62061:2005/A2:2015 2 European foreword The text of document 44/718/CDV, future edition 1 of IEC 62061:2005/A2, prepared by IEC TC 44 “Safety of machinery - Electrotechnical aspects“ was submitted

36、 to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62061:2005/A2:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-05-01 latest date by which the na

37、tional standards conflicting with the document have to be withdrawn (dow) 2018-07-31 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. F

38、or the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of EN 62061:2005. Endorsement notice The text of the International Standard IEC 62061:2005/A2:2015 was approved by CENELEC as a European Standard without any modification. Foreword The text of document 44/46

39、0/FDIS, future edition 1 of IEC 62061, prepared by IEC TC 44, Safety of machinery - Electrotechnical aspects, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62061 on 2004-12-01. The following dates were fixed: latest date by which the EN has to be implemented at nat

40、ional level by publication of an identical national standard or by endorsement (dop) 2005-11-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-12-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commissi

41、on and the European Free Trade Association and covers essential requirements of EC Directive 98/37/EC. See Annex ZZ. PROOF TEST INTERVAL AND LIFETIME The following important information should be noted in relation to the requirements of this standard: Where the probability of dangerous failure per h

42、our (PFHD) is highly dependent upon proof testing (i.e. tests intended to reveal faults not detected by diagnostic functions) then the proof test interval needs to be shown as realistic and practicable in the context of the expected use of the safety-related electrical control system (SRECS) (e.g. p

43、roof test intervals of less than 10 years can be unreasonably short for many machinery applications). CEN/TC114/WG6 have used a proof test interval (mission time) of 20 years to support the estimation of mean time to dangerous failure (MTTFD) for the realization of designated architectures in Annex

44、B of prEN ISO 13849-1. Therefore, it is recommended that SRECS designers endeavour to use a 20 year proof test interval. It is acknowledged that some subsystems and/or subsystem elements (e.g. electro-mechanical components with high duty cycles) will require replacement within the SRECS proof test i

45、nterval. Proof testing involves detailed and comprehensive checks that can, in practice, only be performed when the SRECS and/or its subsystems has been designed to facilitate proof testing (e.g. dedicated test ports) and provided with necessary information (e.g. proof test instructions). To ensure

46、the validity of the proof test interval specified by the designer it is important that any other necessary designated tests (e.g. functional tests) are also successfully performed at the SRECS. Annexes ZA and ZZ have been added by CENELEC. _ Endorsement notice The text of the International Standard

47、IEC 62061:2005 was approved by CENELEC as a European Standard without any modification. _ The contents of the corrigendum of February 2010 have been included in this copy. BS EN 62061:2005Page 2Page 2BS EN 62061:2005+A1:2013EN 62061:2005+A1:2013EC Directive 2006/42/EC. See Annex ZZ.Page 3BS EN 62061

48、:2005+A1:2013EN 62061:2005+A1:2013EN 62061:2005/A1:2013 - 2 - Foreword The text of document 44/655/CDV, future edition 1 of IEC 62061:2005/A1, prepared by IEC TC 44 “Safety of machinery - Electrotechnical aspects“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 62061:200

49、5/A1:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2013-09-18 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-12-18 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsibl