EN 3050-1998 en Aerospace Series - O-Rings in Fluorocarbon Rubber (FKM) Low Compression Set - Technical Specification《航空航天系列 低压力变形氟碳橡胶(FKM)制O型环 交货技术条件》.pdf

《EN 3050-1998 en Aerospace Series - O-Rings in Fluorocarbon Rubber (FKM) Low Compression Set - Technical Specification《航空航天系列 低压力变形氟碳橡胶(FKM)制O型环 交货技术条件》.pdf》由会员分享，可在线阅读，更多相关《EN 3050-1998 en Aerospace Series - O-Rings in Fluorocarbon Rubber (FKM) Low Compression Set - Technical Specification《航空航天系列 低压力变形氟碳橡胶(FKM)制O型环 交货技术条件》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES O-rings, in fluorocarbon rubber (FKM), low compression set - Technical specification The European Standard EN 30501998 has the statmi of a British Standard ICs 49.080 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW ZFw i BS EN 3050:1998 STD-BS

2、I BS EN 3050-ENGL 1998 rn 1624669 0735884 T4 rn BS EN 30601998 National foreword This British Standard is the English language version of EN 3050:1998. The UK participation in its preparation was entrusted to Technical Committee ACEX25, Rubber and elastomeric materials for aerospace purposes, to Sub

3、committee ACE/12/1, Aerospace fasteners - present to the responsible internationaiEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the TJK. A list of o

4、rganizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement intedonal or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Stan

5、dards Correspondznce Index”, or by using the “Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ali the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standa

6、rd does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 8, an inside back cover and a back cover. This British Standard, having been prepared under the direction of the Engineering Sect

7、or Board, was published under the authority of the Standards Board and comes into effect on 15 August 1998 Amendments issued since publication Amd.No. I Date I Text affected O BSI 1998 ISBN O 680 30334 9 - STD-BSI BS EN 3050-ENGL 1998 It624669 0735885 920 W EUROPEAN STANDARD NORME EUROPENNE EUROPISC

8、HE NORM EN 3050 May 1998 ICs 49.080 Descriptors: aircrat industry, O-ring seal, rubber, fluorinated rubber, compression set, hardness, characteristic, specification, quality assurance, acceptance testing, packing English version Aerospace series - O-rings, in fluorocarbon rubber (FKM), low compressi

9、on set - Technical specification Srie arospatiaie - Joints toriques, en lastomre fluorocarbone (FKM). faible dformation rmanente aprs compression - Spcication technique Luft- und Raumfahrt - -Ringe, aus Fluorcarbon-Elastomer (FKM), mit niedrigem Druckverfomungsrest - Technische Lieferbedingungen Thi

10、s European Standard was approved by CEN on 23 February 1998. CEN members are bound to comply with the CENCENELEC Intemal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referen

11、ces concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Stendard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into

12、 its own language and notified to the Central Secretariat has the same status as the official versions. CEN members am the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland. Italy, Luxembourg, Netherlands. Norway, Portugal, Spa

13、in, Sweden, Switzerland and United Kingdom. EUROPEAN COMMEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FUR NORMUNG Central Sacretariat: rue de Stassart, 36 : . _ . .La Q See 4.1. Hardness EN 3376 Density Q 3, see 4.1. Q 3, see 4.1. I. I. . .S2$W. See 4.1, Q A 100 % Corn

14、oression set Resistance to heat ageing Resistance to liquids Surface condition Packaging Requirement 1 Inspection and test method 1 QIA 1 I Sample size In accordance with the I Certificate of compliance I Q I . , EN 2798 After 24 h at 200 OC 25 % max. After 336 h at 200 OC 55 % max. Clai 5.1 5.2 5.3

15、 5.4 5.5 5.5.1 5.5.2 5.6 5.7 5.7.1 5.7.2 5.8 5.9 After 70 h at 250 OC Change in hardness O IRHD to + 5 IRHD After 70 h at 23 OC in liquid B Change in hardness O IRHD to - 5 IRHD Change in volume O%t+5% After 70 h at 200 OC in liquid 101 Change in hardness - 15 IRHD to O IRHD Change in volume O % to

16、+ 15 % Conform to acceptance document II IS0 1817 3, see 4.1. IS0 1817 100 % See annex A. I Visuai examination A Page 6 EN 3050: 1998 Production batch size Table 2: Sampling plans for visual inspections and dimensional charactefistics Sample size Non-destructive tests Destructive tests Acceptance nu

17、mber A B (Ac) Production batch size s 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1200 1201 to 3200 3201 to 10000 10 O01 to 35 O00 35 O01 to 150 O00 150 O01 to 500 O00 Sample size 100 % 13 20 32 50 80 125 200 31 5 500 800 Acceptance number (Ac) and limiting quality (LQ) in accordance with the

18、 acceptable quality level (AQL) AQL 0,065 % Ac - 3- 3- 3- 3- 3- 3- O t 3- 1 f Use sampling plan above. 3- Use sampling plan below. NOTE: The data given in this table are based on single sampling plans for a normal inspection, as specified in IS0 2859-1 (tables Il-A and VI-A). Other sampling plans sp

19、ecified in IS0 2859-1 may be used (double or multiple sampling), but these shall be chosen in such a way as to ensure an equivalent quality level. Table 3: Sampling plans for the inspection of physical Characteristics 5 500 501 to 3 200 3201 to 35000 2 35001 8 13 20 32 I STDmBSI BS EN 3050-ENGL 1998

20、 Lb24669 07L589L 124 H Page 7 EN 3050:1998 Annex A (normative) A. i Packaging Packaging shall conform to the recommendations of IS0 1 749 with the following additional requirements, except for identification. A.l .I General O-rings shall be packed individually. The individual packages may be combine

21、d in collective packages in the form of strips or collective packages with perforations. These packages shall be water vapour-, ozone-, oil- and greaseproof and shall protect the product against compressive stresses. A.1.2 The following package materials may be used for the individual packages: Mate

22、rial of the individual package - opaque polyethylene coated kraft paper; - laminate consisting of aluminium, paper and polyethylene; - opaque polyethylene film. _I - The use of polyvinyl chloride film (PVC film) is not permissible. - I * * Transparent or translucent materials shall not be used. rn A

23、. 1.3 Depending on the size of the O-ring to be packed the following outside dimensions shall be applied for individual packages: Dimensions of the individual packages 55 mm x 55 mm1) 205 mm x 205 mm 11 75mmx 75mm 255 mm x 255 mm 1) 100 mm x 100 mm1) 150 mm x 150 mm1) 300 mm x 300 mm 400 mm x 400 mm

24、 The individual packages shall not be any larger than necessary. O-rings up to 205 mm internal diameter shall be packed flat (no loops or distortion). 1) Sizes in accordance with IS0 1749 - Page 8 EN 3050:1998 A. 1.4 Identification Each individual package and each carton shall be legibly marked with

25、 not less than the following information: Manufacturers identification; Identity according to the product standard; Inspection lot number or inspection and test report number; Quarter and year of vulcanization (e.g. 3Q93 or 3T933; UNLIMITED SHELF LIFE; Manufacturing inspection stamp; DO NOT BEND. Co

26、llective packaging Packaged O-rings shall be in cartons in such a manner that the O-rings are not permanently distorted during shipment and storage and be protected against damage from exposure to weather or any other common hazard. BS EN 3050:1998 BSI 389 Chiswick High Road London w4 4AL STDoBSI BS

27、 EN 3050-ENGL 1998 = 1624669 0715893 TT7 BSI - British Standards Institution BSI is the independent national body responsible for preparing Brikh Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards

28、 are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using thi

29、s British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel 0181 996 9000. Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receiv

30、e the latest editions of standards. Buying standards Orders for ali BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 0181 996 7000. Fax: 0181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementa

31、tion of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Techcal Help to Exporters Service. Various BSI electronic inormatio

32、n services are also available which give details on all its products and services. Contact the Information Centre. Tel 0181 996 7111. Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. F

33、or details of these and other benefits contact Membership Administration. Tel O181 996 7002. Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under t

34、he Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recordmg or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implem

35、enting the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. if permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel O181 996 7070.