EN 2786-2008 en Aerospace series - Electrolytic silver plating of fasteners《航空航天系列 紧固件的电解镀银》.pdf

《EN 2786-2008 en Aerospace series - Electrolytic silver plating of fasteners《航空航天系列 紧固件的电解镀银》.pdf》由会员分享，可在线阅读，更多相关《EN 2786-2008 en Aerospace series - Electrolytic silver plating of fasteners《航空航天系列 紧固件的电解镀银》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 2786:2008Aerospace series Electrolytic silver plating of fastenersICS 49.030.01g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g5

2、8Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIBS EN 2786:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2008 BSI 2008ISBN 978 0 580 60314 3National forewordThis British Standard is the UK implementation of EN 2786

3、:2008.The UK participation in its preparation was entrusted to Technical Committee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provis

4、ions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsLicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPEN

5、NEEUROPISCHE NORMEN 2786March 2008ICS 49.030.01English VersionAerospace series - Electrolytic silver plating of fastenersSrie arospatiale - Argentage lectrolytique des lmentsde fixationLuft- und Raumfahrt - Elektrolytisches Versilbern vonVerbindungselementenThis European Standard was approved by CEN

6、 on 12 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards m

7、ay be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CE

8、N Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

9、 Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any for

10、m and by any means reservedworldwide for CEN national Members.Ref. No. EN 2786:2008: ELicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Purpose of process .4 4 Technical requirement 4 5 Required characteristics.5 6 Classificati

11、on of tests6 7 Quality assurance6 BS EN 2786:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI3 Foreword This document (EN 2786:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in

12、accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publicati

13、on of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC

14、shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark,

15、Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 2786:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy

16、, (c) BSI4 1 Scope This standard specifies the electrolytic silver plating of fasteners used in aerospace applications. It shall apply whenever referenced. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

17、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2828, Aerospace series Adhesion test for metallic coatings by burnishing. EN 2830, Aerospace series Adhesion test for metallic coatings by shearing action. EN 2831, Ae

18、rospace series Hydrogen embrittlement of steels Test by slow bending. EN 2832, Aerospace series Hydrogen embrittlement of steels Notched specimen test. EN 9100, Aerospace series Quality management systems Requirements (based on ISO 9001:2000) and Quality systems Model for quality assurance in design

19、, development, production, installation and servicing (based on ISO 9001:1994). 3 Purpose of process To prevent galling or seizure. 4 Technical requirement 4.1 Preparation Parts shall have chemically and/or electrolytically clean surfaces prepared with minimum abrasion, erosion or pitting, prior to

20、immersion in the plating solution. Treatments which may produce hydrogen embrittlement shall be avoided. After cleaning and prior to immersion in the plating solution, parts may be etched in a suitable solution such as ferric chloride and/or hydrochloric acid, to promote adhesion. Electrical contact

21、 between the parts and the power source shall be established in such a manner as to ensure that neither chemical/immersion deposition nor electrical arcing or overheating will occur. 4.2 Procedure The parts shall be silver plated over a suitable nickel and/or silver strike by an approved method to t

22、he thickness quoted in the product standard or in the definition document. The plated parts shall be removed from the plating solution then thoroughly rinsed and dried. BS EN 2786:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI5 5 Required characteristics 5.1 Appearance The silver p

23、late shall be sound, smooth, continuous, uniform in color and free from blisters and other imperfections (see 5.4.2). Abrasion of plating on corners and edges of threaded fasteners is acceptable, but plate shall be continuous on the threads. Marking of the cone section of self-locking nuts, produced

24、 in off-setting the locking beams or other deformation, is acceptable. 5.2 Composition Silver as plated shall be not less than 99,9 % pure, the process of plating shall be controlled to produce this purity. 5.3 Post treatments De-embrittlement is mandatory on martensitic steel where the tensile stre

25、ngth can exceed 1 100 MPa. De-embrittlement, where applicable, shall be carried out as soon as possible, but no later than 16 h after plating, the time and temperature are optional. Where de-embrittlement is specified, the parts or test pieces shall be tested to EN 2831 or EN 2832 or parts shall be

26、subjected for 200 h at ambient temperature to an axial load equal to 75 % of the tensile strength of the part and must show satisfactory results. No fracture is permissible before 200 h. 5.4 Adhesion 5.4.1 General To be checked on parts or test pieces. These parts or test pieces shall be heated in a

27、ir to the following applicable temperature held at temperature within 8 C for no less than two hours and cooled in still air. a) Parts with a maximum test temperature of up to and including 425 C: The temperature of any de-embrittlement shall be considered sufficient. If no de-embrittlement is carri

28、ed out, the temperature shall be the maximum test temperature of the parts. b) Parts with a maximum test temperature of more than 425 C: The temperature shall be the maximum test temperature of the parts. 5.4.2 Adhesion requirements After heating, parts or test pieces shall be visually examined at 1

29、0 times magnification. Parts shall be free of detrimental blisters and of indications of poor bond such as flaking and lifting of the plating. Some small blisters are acceptable provided the parts meet the adherence requirements. Blisters 0,38 mm and larger in diameter, are not acceptable. After vis

30、ual examination, the parts or test pieces shall be subjected to one of the following adhesion tests, EN 2828, EN 2830 or any other adhesion test that is agreed. BS EN 2786:2008Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI6 6 Classification of tests 6.1 Acceptance tests The following t

31、ests shall be carried out on each lot: a) Appearance (see 5.1); b) Thickness (as defined on the product standard or definition document) to be measured by an agreed method; c) Adhesion (see 5.4, 5.4.2). NOTE A lot shall be all parts of the same size and shape, made of the same alloy, plated to the s

32、ame thickness in the same set of solutions within one 24 h period. 6.2 Periodic tests The following tests shall be performed at a frequency selected by the process controller: a) Composition (see 5.2); b) Post treatments (see 5.3). 7 Quality assurance EN 9100. BS EN 2786:2008Licensed Copy: :FULLNAME

33、, : DATE, Uncontrolled Copy, (c) BSIblankLicensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSIBS EN 2786:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on stand

34、ards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of

35、our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 899

36、6 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 899

37、6 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise reque

38、sted.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services.

39、 Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Member

40、ship Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyrig

41、ht subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form o

42、r by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for a

43、ny other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.Licensed Copy: :FULLNAME, : DATE, Uncontrolled Copy, (c) BSI