EN 12312-18-2005 en Aircraft ground support equipment - Specific requirements - Part 18 Nitrogen or Oxygen units (Incorporates Amendment A1 2009)《航空地面辅助设备 特殊要求 第18部分 氮或氧装置 包含修改件A1-.pdf

《EN 12312-18-2005 en Aircraft ground support equipment - Specific requirements - Part 18 Nitrogen or Oxygen units (Incorporates Amendment A1 2009)《航空地面辅助设备 特殊要求 第18部分 氮或氧装置 包含修改件A1-.pdf》由会员分享，可在线阅读，更多相关《EN 12312-18-2005 en Aircraft ground support equipment - Specific requirements - Part 18 Nitrogen or Oxygen units (Incorporates Amendment A1 2009)《航空地面辅助设备 特殊要求 第18部分 氮或氧装置 包含修改件A1-.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、nullnullnullnullnullnullnull nullnullnullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnullnull nullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnullnullnull nullnullnullnullnullnullnullnullnullnullnulln

2、ullnullnullnullnullnullnullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnull nullnullnullnullnullnullnullnull nullnullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnul

3、lnullnull nullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnullnull+A1:2009BS EN 12312-18:2005+A1:2009ISBN 978 0 580 61082 0Amendments/corrigenda issued since publicationDate Comments 31 October 2009 Implementation of CEN amendm

4、ent A1:2009National forewordThis British Standard is the UK implementation of EN 12312-18:2005+A1:2009. It supersedes BS EN 12312-18:2005, which is withdrawn.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry th

5、e number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committee ACE/57, Air cargo and ground support equipment.A list of organizations represented on this committee can be obtained on request

6、 to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the

7、 Standards Policy and Strategy Committee on 30 June 2005 BSI 2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12312-18:2005+A1 April 2009 ICS 49.100 Supersedes EN 12312-18:2005English Version Aircraft ground support equipment - Specific requirements - Part 18: Nitrogen or Oxygen units Matrie

8、l au sol pour aronefs - Exigences particulires - Partie 18: Matriels dalimentation en azote ou en oxygneLuftfahrt-Bodengerte - Besondere Anforderungen - Teil 18: Stickstoffgerte oder Sauerstoffgerte This European Standard was approved by CEN on 28 February 2005 and includes Amendment 1 approved by C

9、EN on 1 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards

10、may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the

11、 CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Nether

12、lands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation i

13、n any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12312-18:2005+A1:2009: EEN 12312-18:2005+A1:2009 (E) 2 Contents Page Foreword 3 1 Scope 52 Normative references 53 Terms and definitions . 64 List of hazards 65 Safety requirements and/or measures 75.1 General requi

14、rements for nitrogen and oxygen units 75.2 Pressure vessels 75.3 Pressure filling system . 75.4 Hoses 75.5 Special requirements for oxygen units only . 86 Information for use 86.1 Marking . 86.2 Safety marking . 86.3 Instructions 87 Verification of requirements . 9Annex A (informative) Examples of n

15、itrogen or oxygen units 10Annex B (normative) List of hazards in addition to those of EN 1915-1 12Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC, amended by Directive 98/79/EC 13Annex ZB (informative) !Relationship between t

16、his European Standard and the Essential Requirements of EU Directive 2006/42/EC“ . 14Bibliography 15BS EN 12312-18:2005+A1:2009EN 12312-18:2005+A1:2009 (E) 3 Foreword This document (EN 12312-18:2005+A1:2009) has been prepared by Technical Committee CEN/TC 274 “Aircraft ground support equipment” the

17、secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. This docume

18、nt includes Amendment 1, approved by CEN on 2009-03-01. This document supersedes EN 12312-18:2005. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and the Eur

19、opean Free Trade Association and supports essential requirements of EU Directive(s). !For relationship with EU Directives, see informative Annexes ZA and ZB, which are integral parts of this document.“ The Parts of EN 12312 Aircraft ground support equipment Specific requirements are: Part 1: Passeng

20、er stairs Part 2: Catering vehicles Part 3: Conveyor belt vehicles Part 4: Passenger boarding bridges Part 5: Aircraft fuelling equipment Part 6: Deicers and deicing/antiicing equipment Part 7: Aircraft movement equipment Part 8: Maintenance stairs and platforms Part 9: Container/Pallet loaders Part

21、 10: Container/Pallet transfer transporters Part 11: Container/Pallet dollies and loose load trailers Part 12: Potable water service equipment Part 13: Lavatory service equipment Part 14: Disabled/Incapacitated passenger boarding equipment Part 15: Baggage and equipment tractors Part 16: Air start e

22、quipment Part 17: Air conditioning equipment Part 18: Nitrogen or Oxygen units Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions Part 20: Ground power equipment According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bou

23、nd to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Den-mark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

24、Switzerland and United Kingdom. BS EN 12312-18:2005+A1:2009EN 12312-18:2005+A1:2009 (E) 4 Introduction This document specifies health and safety requirements, as well as some functional and performance requirements for nitrogen or oxygen units intended to be used for all aircraft types commonly in s

25、ervice in civil air transport. The minimum essential criteria are considered to be of primary importance in providing safe, serviceable, economical and practical nitrogen or oxygen units. Deviations from the recommended criteria should occur only after careful consideration, extensive testing, risk

26、assessment and thorough service evaluation have shown alternative methods or conditions to be satisfactory. This document is a Type C standard as stated in !EN ISO 12100“. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope

27、of this document. When provisions of this Type C standard are different from those which are stated in Type A or B standards, the provisions of this Type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions

28、of this Type C standard. BS EN 12312-18:2005+A1:2009EN 12312-18:2005+A1:2009 (E) 5 1 Scope This document specifies the technical requirements to minimise the hazards listed in Clause 4 which can arise during the commissioning, operation and maintenance of nitrogen or oxygen units when carried out in

29、 accordance with the specifications given by the manufacturer or his authorised representative. It also takes into account some performance requirements recognised as essential by authorities, aircraft and ground support equipment (GSE), manufacturers as well as airlines and handling agencies. This

30、document applies to: all types of mobile nitrogen units and oxygen units with transportable gas cylinders interchangeable for filling purposes; equipment to be carried with other GSE or vehicles, e.g. skid mounted units, intended for the manual refill of gaseous nitrogen or oxygen on aircraft (Examp

31、les see Annex A). NOTE Generally oxygen units are used under aircraft maintenance conditions, not under commercial servicing conditions. This document does not establish requirements for noise and vibration. Noise and vibration are dealt with respectively in EN 1915-4 and EN 1915-3. This document do

32、es not deal with hazards in respect to a standard automotive chassis and from other vehicles on the apron. This Part of EN 12312 is not applicable to nitrogen or oxygen units which are manufactured before the date of publication of this document by CEN. !This part of EN 12312 is intended to be used

33、in conjunction with EN 1915-1, EN 1915-2, EN 1915-3 (for vehicles) and EN 1915-4.“ 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the

34、 referenced document (including any amendments) applies. EN 837-1, Pressure gauges Part 1: Bourdon tube pressure gauges Dimensions, metrology, requirements and testing EN 849, Transportable gas cylinders Cylinder valves Specification and type testing !EN 983“, Safety of machinery Safety requirements

35、 for fluid power systems and their components Pneumatics EN 1050:1996, Safety of machinery Principles for risk assessment EN 1175-1, Safety of industrial trucks Electrical requirements Part 1: General requirements for battery pow-ered trucks EN 1915-1:2001, Aircraft ground support equipment General

36、requirements Part 1: Basic safety requirements EN 1915-2, Aircraft ground support equipment General requirements Part 2: Stability and strength require-ments, calculations and test methods BS EN 12312-18:2005+A1:2009EN 12312-18:2005+A1:2009 (E) 6 !EN 1915-3, Aircraft ground support equipment General

37、 requirements Part 3: Vibration measurement methods and reduction“ !EN 1915-4, Aircraft ground support equipment General requirements Part 4: Noise measurement methods and reduction“ EN 1964-1, Transportable gas cylinders Specification for the design and construction of refillable transportable seam

38、less steel gas cylinders of water capacities from 0,5 litre up to and including 150 litres Part 1: Cylinders made of seamless steel with an Rmvalue of less than 1100 MPa EN ISO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic termi-nology, methodology (IS

39、O 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003). 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100:2003 and EN 1915-1:2001 and the following

40、 apply. 3.1 nitrogen unit mobile or transportable ground support equipment (GSE) to replenish aircraft nitrogen systems including tyres 3.2 oxygen unit mobile or transportable ground support equipment (GSE) to replenish aircraft oxygen systems 3.3 nitrogen or oxygen truck self-propelled unit, equipp

41、ed with ride-on driver accommodation 3.4 nitrogen or oxygen cart towable unit 3.5 pedestrian controlled nitrogen or oxygen cart self- propelled unit without ride-on driver accommodation 3.6 skid mounted nitrogen or oxygen unit unit mounted on a pallet or frame to be loaded on a vehicle by a fork lif

42、t truck or crane 3.7 pressure filling system means to fill/refill pressurised systems, e.g. oxygen system, tyres, actuators 4 List of hazards The list of risks and hazards (see Annex B) is based on EN 1050 and contains the hazards and hazardous situations, as far as they are dealt with in this docum

43、ent, identified by risk assessment as significant for nitrogen or oxygen units and which require action to eliminate or reduce risks. BS EN 12312-18:2005+A1:2009EN 12312-18:2005+A1:2009 (E) 7 5 Safety requirements and/or measures 5.1 General requirements for nitrogen and oxygen units 5.1.1 Units sha

44、ll be designed for use with one type of gas only. 5.1.2 !Units shall conform to the relevant requirements of EN 1915-1, EN 1915-2, EN 1915-3 and EN 1915-4 unless otherwise specified in this standard.“ 5.1.3 Stability and strength calculations shall be carried out in accordance with EN 1915-2. 5.1.4

45、The overall dimensions shall be kept to a minimum (see Clause 0 of EN 1915-1:2001 negotiation). 5.1.5 The electrical system of battery powered self-propelled units shall conform to EN 1175-1. 5.1.6 Self-propelled units not designed to be pedestrian controlled shall be equipped with ride-on driver ac

46、commo-dation. 5.1.7 Restraint systems shall be fitted to all seats on self-propelled units. Minimum requirement: a lap type seat belt. 5.1.8 Structural parts of pedestrian controlled self-propelled units shall not protrude within the operating range of the tiller. 5.1.9 Self-propelled units with dri

47、vers cabin shall have an alternative means of exit for the driver in the event of an emergency. It shall be positioned as far as possible away from the normal exit. 5.1.10 Towable units shall be capable of being towed at speeds up to 32 km/h (20 mph). NOTE The maximum travelling speed of towable uni

48、ts should be stipulated between manufacturer and user (see Clause 0 of EN 1915-1:2001 negotiation). 5.2 Pressure vessels 5.2.1 Gas cylinders shall meet the requirements of EN 1964-1. 5.2.2 Gas cylinders shall be secured in their provided positions, e.g. by clamping, permanent fixing. 5.2.3 Gas cylin

49、ders mounted on units with internal combustion engines shall be protected against exceeding the allowable temperature caused by the engine and/or the exhaust system, e.g. by distance, shielding. 5.2.4 Cylinder valves shall meet the requirements of EN 849. 5.2.5 Cylinder valves of gas cylinders in the mounted position on the unit shall be within the contour of the unit. Otherwise they shall be protected against mechanical damage, e.g. by soli