DLA SMD-5962-87620 REV E-2009 MICROCIRCUIT HYBRID LINEAR HIGH POWER OPERATIONAL AMPLIFIER.pdf

《DLA SMD-5962-87620 REV E-2009 MICROCIRCUIT HYBRID LINEAR HIGH POWER OPERATIONAL AMPLIFIER.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87620 REV E-2009 MICROCIRCUIT HYBRID LINEAR HIGH POWER OPERATIONAL AMPLIFIER.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Remove vendor CAGE 13919. Add device type 02. Add vendors CAGE 31757 and 60024. Change to reflect MIL-H-38534 processing. Editorial changes throughout. 91-09-13 Tim H. Noh B Table I, device type 01, correct output voltage peak and output current

2、peak tests. 00-01-11 Raymond Monnin C Drawing updated to reflect current requirements. -sld 02-12-16 Raymond Monnin D Figure 1, case outline X, dimension C, delete 0.260“ minimum and change 0.300“ maximum to 0.340“ maximum. 03-09-25 Raymond Monnin E Table I, input offset current, device type 01, sub

3、group 2, change min/max limits from 7 nA to 15 nA. Table I, current limits, device type 02, change test conditions to VCC= 14 V dc, RCL= 1 , RL= 6 and change min/max limits to 0.6 A / 0.89 A. Table II, add note to Group C end-point test parameters. -gz 09-07-27 Charles F. Saffle THE ORIGINAL FIRST S

4、HEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Donald R. Osborne DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. Di Cenzo COLUMBUS, OHIO 43218-3990http:/w

5、ww.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N. A. Hauck MICROCIRCUIT, HYBRID, LINEAR, HIGH POWER OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 87-09-16 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-87620 SHEET 1 OF

6、12 DSCC FORM 2233 APR 97 5962-E397-09Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1

7、Scope. This drawing documents one product assurance class, class H (high reliability) and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). 1.2 PIN. The PIN shall be as shown in the following example: 5962-87620 01 X X Drawing number

8、 Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 42106, PA51M-1/883 High power operational amplifier 02 42106-1, PA51M/883 High power operational

9、 amplifier 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Flange mount Y See figure 1 8 Flange mount 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3

10、 Absolute maximum ratings. Supply voltage range 40 V dc maximum Differential input voltage . VCC- 3 V Common mode input VCCMaximum power dissipation (PD): Device type 01 80 W 1/ Device type 02 97 W 2/ Thermal resistance, junction-to-case (JC): Device type 01 2.2C/W Device type 02 1.8C/W Junction tem

11、perature (TJ) . +200C Lead temperature (soldering, 10 seconds) . +300C Storage temperature range . -65C to +150C 1.4 Recommended operating conditions. Supply voltage (VCC) 34 V dc Operating temperature range: Device type 01 (TA) . -55C to +125C Device type 02 (TC) . -55C to +125C 1/ At ambient tempe

12、rature of +25C, derate at 2.2C/W above ambient temperature of +25C. 2/ At case temperature of +25C, derate at 1.8C/W above case temperature of +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFEN

13、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless

14、otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - In

15、terface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standar

16、dization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes

17、applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device class H shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests here

18、in or as designated in the device manufacturers Quality Management (QM) plan or as designated for applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applic

19、able device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and h

20、erein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance ch

21、aracteristics are as specified in table I and shall apply over the full specified operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH

22、IO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordan

23、ce with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain th

24、e electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained unde

25、r document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original c

26、opy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing.

27、4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Scre

28、ening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition B or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made availabl

29、e to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C minimum for device type 01 and TC= +125C minimum fo

30、r device type 02. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

31、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VCC= 34 V dc unless otherwise specified Group

32、 A subgroups Device type Limits Unit Min Max Input offset voltage VIOTA= +25C 1 01 -5 +5 mV Input offset voltage drift DVIOTA= -55C and +125C 2, 3 01 -40 +40 V/C Input bias current IIB1 01-20 +20 nA 2, 3 -35 +35 Input offset current IIO1 01-3 +3 nA 2 -15 +15 3 -7 +7 Power supply rejection ratio +PSR

33、R -VCC= -34 V dc, +VCC= +10 V to +40 V dc 1 01 -100 +100 V/V 2, 3 -200 +200 -PSRR +VCC= +34 V dc, -VCC= -10 V to -40 V dc 1 -100 +100 2, 3 -200 +200 Common mode rejection ratio CMRR VCM= 22 V, f = dc 1 01 80 dB 2, 3 76 Supply current ICCVCM= 0 V, no load condition 1, 2, 3 01 -10 +10 mA Output voltag

34、e peak VOPIO= 10 A peak 4 01 -26 V IO= 10 A peak 4 26 RL= 10 k 5, 6 -30 RL= 10 k 5, 6 30 Output current peak IOPRL= 2.6 , TA= +25C 4 01 10 A Voltage gain AVSRL= 10 k 4, 5, 6 01 94 dB Slew rate SR RL= 6.5 , TA= +25C 4 01 1.35 V/s Provided by IHSNot for ResaleNo reproduction or networking permitted wi

35、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C VCC= 34 V dc unless

36、otherwise specified Group A subgroups Device type Limits Unit Min Max Supply current ISVIN= 0 V dc, G = 100, 2/ RCL= 0.1 , VCM= 0 V dc 1, 3 02 10 mA 2 13 Input offset voltage VOSVIN= 0 V dc, G = 100, 2/ RCL= 0.1 , VCC= 10 V dc 1 02 -16.0 +16.0 mV 2 -22.5 +22.5 3 -21.2 +21.2 VIN= 0 V dc, G = 100, 2/

37、RCL= 0.1 , VCC= 34 V dc 1 -10.0 +10.0 2 -16.5 +16.5 3 -15.2 +15.2 VIN= 0 V dc, G = 100, 2/ RCL= 0.1 , VCC= 40 V dc 1 -11.2 +11.2 2 -17.7 +17.7 3 -16.7 +16.7 Input bias current (+IN) +ISVIN= 0 V dc, RBIAS 100 M 1 02 40.0 nA 2, 3 80.0 Input bias current (-IN) -ISVIN= 0 V dc, RBIAS 100 M 1 02 40.0 nA 2

38、, 3 80.0 Input offset current IOSVIN= 0 V dc, RBIAS 100 M 1 02 10.0 nA 2, 3 30.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, O

39、HIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C VCC= 34 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOVCC= 40 V dc, IO= 68 mA, RL= 5

40、00 4, 5, 6 02 34 V VCC= 34 V dc, IO= 4 A, RL= 6 4, 5, 6 24 VCC= 18 V dc, IO= 10 A, RL= 1 , TC= +25C and -55C 4, 6 10 VCC= 16 V dc, IO= 8 A, RL= 1 , TC= +125C 5 8 Current limits ICLVCC= 14 V dc, RCL= 1 , RL= 6 , TC= +25C 2 / 4 02 0.6 0.89 A Stability/noise ENVCC= 34 V dc, CL= 1.5 nF, G = 1 4, 5, 6 02

41、 1.0 mV Slew rate SRVCC= 34 V dc, VIN 4 Vp-p, RL= 500 4, 5, 6 02 1.0 10 V/s Open loop gain AOLVCC= 34 V dc, VIN 4 Vp-p, RL= 500 , f = 15 Hz 4, 5, 6 02 91 dB Common mode rejection CMRVCC= 15 V dc, VCM= 9 V dc, +f = dc 4, 5, 6 02 70 dB 1/ During all group A testing, terminal connection F. O. (pin 7) i

42、s left open. 2/ A current limiting resistor (RCL) is connected between CL+ to the output and CL- to the output during these tests. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER C

43、OLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Symbol Inches MillimetersMin Max Min MaxA 1.510 1.550 38.35 39.37B .745 .770 18.92 19.56C .340 8.64D 0.038 .042 .97 1.07E 0.080 .105 2.03 2.67F 40 BSC 40 BSCG .500 BSC 12.7 BSCH 1.186 BSC 30.12 BSCJ .593

44、 BSC 15.06 BSCK .400 .500 10.16 12.70Q .151 .161 3.84 4.09R .980 1.020 24.89 25.91NOTES: 1. Leads in true position within .010 inch (0.25 mm) R at MMC at seating plane. 2. The U. S. preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of

45、measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 3. Pin numbers are for reference and may not be marked on package. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

46、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87620 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 Case outline Y. Symbol Inches MillimetersMin Max Min MaxA 1.510 1.550 38.35 39.37B .745 .770 18.92 19.56C .225 .250 5.71 6.35D .038 .042 .97

47、1.07E .080 .105 2.03 2.67F 40 BSC 40 BSCG .500 BSC 12.7 BSCH 1.186 BSC 30.12 BSCJ .593 BSC 15.06 BSCK .400 .500 10.16 12.70Q .151 .161 3.84 4.09R .980 1.020 24.89 25.91NOTES: 1. Leads in true position within .010 inch (0.25 mm) R at MMC at seating plane. 2. The U. S. preferred system of measurement

48、is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 3. Pin numbers are for reference and may not be marked on package. FIGURE 1. Case outlines - Continued. Provided by IHSNot for R