DLA SMD-5962-87617 REV G-2013 MICROCIRCUIT HYBRID DIGITAL HIGH VOLTAGE DRIVERS.pdf

《DLA SMD-5962-87617 REV G-2013 MICROCIRCUIT HYBRID DIGITAL HIGH VOLTAGE DRIVERS.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87617 REV G-2013 MICROCIRCUIT HYBRID DIGITAL HIGH VOLTAGE DRIVERS.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changed to reflect MIL-H-38534 processing. Editorial changes throughout. 92-03-23 K. A. Cottongim B Changed in accordance with NOR 5962-R111-95. 95-04-11 K. A. Cottongim C Add vendor CAGE codes 31757 and 51651. Changes to table I. 98-03-05 K. A.

2、Cottongim D Changes to table I, conditions column for device type 02. Add case outline Y. 99-02-19 K. A. Cottongim E Updated drawing to the latest requirements. -sld 05-04-04 Raymond Monnin F Updated drawing paragraphs -sld 12-02-02 Charles F. Saffle G Add device types 03 and 04. -gc 13-05-20 Charle

3、s F. Saffle THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Charles E. Besore DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STAND

4、ARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Robert P. Evans MICROCIRCUIT, HYBRID, DIGITAL, HIGH VOLTAGE DRIVERS DRAWING APPROVAL DATE 87-11-10 AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 6

5、7268 5962-87617 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E367-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 A

6、PR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for class H hybrid microcircuits to processed in accordance with MIL-PRF-38534. 1.2 PIN. The PIN shall be as shown in the following example: 5962-87617 01 X A Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2

7、.2) (see 1.2.3) 1.2.1 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 0006, 51992, 11105, 11563 1.5 amperes, high voltage driver 02 0008 3.0 amperes, high voltage, high current driver 03 0006 1.5 amperes, high voltage driver

8、 04 0008 3.0 amperes, high voltage, high current driver 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 10 Can (with standoff) Y See figure 1 10 Can (without standoff) 1.2.3 Lead

9、 finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ 2/ Peak power supply voltage (VP), for less than 0.1 s +60 V dc Continuous supply voltage (VS) . +45 V dc Input voltage (VIN) +5.5 V dc Input extender current (IX) 5.0 mA Peak output current (IOUT), 50

10、ms on, 1 s off: Device type 01,03 1.5 A Device type 02,04 3.0 A Continuous output current (IOUTC): Device type 01,03 0.4 A Device type 02,04 0.5 A Thermal resistance, junction-to-case (JC) . (See MIL-STD-1835) Power dissipation (PD), TA= +25C: Device type 01,03 750 mW 3/ Device type 02,04 950 mW 3/

11、Junction temperature (TJ) . +175C Storage temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +300C 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2

12、/ Unless otherwise specified, all voltages are referenced to ground. 3/ Derate at 210C/W above TA= +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 R

13、EVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawi

14、ng to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Metho

15、d Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.d

16、la.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this docu

17、ment, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 s

18、hall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as de

19、fined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimen

20、sions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Switching time waveform(s). The switching time wave

21、form(s) shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The

22、electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In additio

23、n, the manufacturers vendor similar PIN may also be marked. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97

24、 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, th

25、e data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certif

26、icate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38

27、534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38

28、534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN

29、G SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Logic “1“ input voltage

30、 1/ VIH10 V VCC 45 V 1,2,3 01,02 2.0 V 20 V VCC 45 V 03,04 2.0 Logic “0“ input voltage 1/ VIL10 V VCC 45 V 1,2,3 01,02 0.8 V 20 V VCC 45 V 03,04 0.8 Logic “1“ output voltage VOHVCC= 10 V, VIN= 2 V, 1/ IOUT= 150 mA 1, 2, 3 01 8.8 V VCC= 28 V, VIN= 2 V, RL= 82 26.5 VCC= 28 V, VIN= 2 V, RL= 40 1, 2, 3

31、02 26.5 VCC= 45 V, VIN= 2 V, 1/ IOUT= 1.6 A 02,04 43.0 VCC= 20 V, VIN= 2 V, 1/ RL= 82 1, 2, 3 03 13 VCC= 28 V, VIN= 2 V, RL= 82 26.5 VCC= 20 V, VIN= 2 V, RL= 100 1, 2, 3 04 13 VCC= 28 V, VIN= 2 V, RL= 40 26.5 Logic “0“ output voltage VOLVCC= 45 V, VIN= 0.8 V, RL= 100 1, 2, 3 01,03 10 mV 02,04 100 Se

32、e footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc

33、e characteristics - Continued. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Logic “1“ input current 1/ IIHVCC= 45 V, VIN= 2.4 V 1,2,3 All 5.0 A VCC= 45 V, VIN= 5.5 V 100 Logic “0“ input current 1/ IILVCC= 45 V, VIN= 0.4 V 1, 2, 3 Al

34、l -1.0 mA Input breakdown voltage 1/ BVIN1,2,3 All 5.5 V “Off“ power supply current ICC(off) VCC= 45 V, VIN= 0.8 V 1,2,3 01,03 2.0 mA VCC= 45 V, VIN= 0 V 02,04 2.0 “On“ power supply current ICC(on) VCC= 45 V, VIN= 2 V, IOUT= 0 mA 1, 2, 3 All 8.0 mA Rise time 2/ trVCC= 28 V, VIN= 5 V, RL= 82 , see fi

35、gure 3 9, 10, 11 01,03 300 ns VCC= 28 V, VIN= 5 V, RL= 40 , see figure 3 02,04 500 Fall time 2/ tfVCC= 28 V, VIN= 5 V, RL= 82 , see figure 3 9, 10, 11 01,03 1.7 s VCC= 28 V, VIN= 5 V, RL= 40 , see figure 3 9,11 02,04 4.0 10 6.0 Turn on time 2/ tONVCC= 28 V, VIN= 5 V, RL= 82 , see figure 3 9, 10, 11

36、01,03 1.0 s VCC= 28 V, VIN= 5 V, RL= 40 , see figure 3 02,04 1.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION L

37、EVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Turn off time 2/ tOFFVCC= 28 V, VIN= 5 V, RL= 82 , see figure 3 9, 10, 11 01,03 8.0 s VCC

38、= 28 V, VIN= 5 V, RL= 40 , see figure 3 9,11 02,04 10 10 14 1/ Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 2/ Subgroups 10 and 11 shall be tested as part of device initial characterization and after design and process changes. Parameter shal

39、l be guaranteed to the limits specified in table I for all lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G

40、SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbol Min Max Min Max A 3.94 4.70 .155 .185 b 0.38 0.48 .015 .019 D 8.51 9.40 .335 .370 D1 7.75 8.51 .305 .335 D2 3.05 4.06 .120 .160 e 5.84 BSC .230 BSC F 1.02 .040 k 0.66 0.86 .026 .034 k1 0.74 1.14 .029 .045 L 12.70 .500 Q 1.27 .05

41、0 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers shown for reference only. FIGURE 1. Ca

42、se outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 9 DSCC FORM 2234 APR 97 Case outline Y. Millimeters Inches Symbol Mi

43、n Max Min Max A 3.94 4.70 .155 .185 b 0.38 0.48 .015 .019 D 8.51 9.40 .335 .370 D1 7.75 8.51 .305 .335 e 5.84 BSC .230 BSC F 1.02 .040 k 0.66 0.86 .026 .034 k1 0.74 1.14 .029 .045 L 12.70 .500 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-poun

44、d units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers shown for reference only. FIGURE 1. Case outline(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

45、se from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 10 DSCC FORM 2234 APR 97 FIGURE 2. Terminal connections and functional diagram (top view). FIGURE 3. Switching time waveforms. Provided by IHSNot for ResaleNo reprod

46、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87617 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 11 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance

47、 with MIL-PRF-38534, group A test table) Interim electrical parameters 1 Final electrical parameters 1*, 2, 3, 9 Group A test requirements 1, 2, 3, 9, 10, 11 Group C end-point electrical parameters 1, 2, 3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicable

48、* PDA applies to subgroup 1. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to