DLA SMD-5962-09234 REV B-2012 MICROCIRCUIT HYBRID PRECISION CURRENT SOURCE QUINTET.pdf

《DLA SMD-5962-09234 REV B-2012 MICROCIRCUIT HYBRID PRECISION CURRENT SOURCE QUINTET.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-09234 REV B-2012 MICROCIRCUIT HYBRID PRECISION CURRENT SOURCE QUINTET.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Figure 2 and Table III, changed pin 7 from NC “no connection“ to “CASE_GND“ and added a note regarding pin 7 should be grounded. -sld 11-09-01 Charles F. Saffle B Table I; Added the test “Source current off 1-5“, changed the max limit for the tes

2、t Comparator Reference In Current from “1000 nA“ to “1200 nA“, changed the condition “Isink“ to 2.0 mA for the test Output Voltage Low 1-5. Changed the min and max limits for the test BG Regulator Output Voltage for subgroups 2 and 3 from “1.990 and 2.010“ to “1.980 and 2.020“, removed the BG Regula

3、tor Maximum Source Current test and renamed the BG Regulator Maximum Sink Current to BG Regulator Load Regulation with the conditions IBG= 0 to 2 mA and the min and max limit of -5 and +5 mV. Changed “C1“ in the conditions block from “28 pF“ to “37 pF“ for the tests Comparator Pulse Delay Low to Hig

4、h and Comparator Pulse Delay High to Low. Changed the max limit for the Comparator Pulse Delay High to Low test from “120 ns“ to “150 ns“. Changed the max limit for the Comparator Pulse Delay Low to High test to “10 s“. Changed the min limit for the Enable Delay to VOUT(tEDVHL) from “1000 ns“ to “50

5、0 ns“. -sld 12-04-30 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING THIS DRAW

6、ING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Greg Cecil APPROVED BY Charles F. Saffle MICROCIRCUIT, HYBRID, PRECISION CURRENT SOURCE, QUINTET DRAWING APPROVAL DATE 11-04-04 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-09234 SHEET 1 OF 12 D

7、SCC FORM 2233 APR 97 5962-E299-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This

8、drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected i

9、n the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 09234 01 K X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hard

10、ness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic

11、 number Circuit function 01 PCS5035 Precision Current Source, Quintet 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qua

12、lification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level i

13、s intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow

14、, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the devi

15、ce acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have

16、 a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The ca

17、se outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 18 Flat package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) +7.0 V dc Comp

18、arator input voltage range -0.5 V dc to +3.1 V dc Junction temperature (TJ) +150 C Power dissipation (PD) . 0.1 W Thermal resistance, junction-to-case (JC) . 6 C/W Lead temperature (soldering, 10 seconds) 300 C Storage temperature -65 C to +150 C 1.4 Recommended operating conditions. Supply voltage

19、(VCC) +4.75 V dc to +5.25 V dc Case operating temperature range (TC) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise spec

20、ified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Stand

21、ard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Doc

22、ument Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable l

23、aws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or netwo

24、rking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G,

25、H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or op

26、timize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design,

27、construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be

28、as specified on figure 2. 3.2.3 Schematic diagram(s). The schematic diagram(s) shall be as specified on figure 3. 3.2.4 Timing diagram(s) . The timing diagram(s) shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performan

29、ce characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Mark

30、ing of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the ma

31、nufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which,

32、 if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer

33、in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as require

34、d in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modifi

35、cation in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SH

36、EET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TC +125 C VCC= +5.0 V dc 5% Group A subgroups Device type Limits Unit unless otherwise specified Min Max Source Current 1-5 IO0 VIN 3.1 V, VEN= VENH1,2,3 01 78 82 A Source current off 1-5 IOFF 0

37、 VIN 3.1 V, VEN= VENL1,2,3 01 150 nA Comparator In Voltage 1/ VINIOUT= 80 A 1,2,3 01 0 3.1 V Comparator Reference Voltage 1/ VREF 1,2,3 01 3.1 V Comparator Reference In Current IREF1,2,3 01 1200 nA Enable Input Voltage Low VENL 1,2,3 01 0.8 V Enable Input Voltage High VENH1,2,3 01 2.4 V Comparator H

38、ysteresis 1/ 1,2,3 01 30 mV Output Voltage Low 1-5 VOLISINK 2.0 mA 1,2,3 01 0.4 V Output Voltage High 1-5 VOH1,2,3 01 4.4 V Input Zener Clamp Voltage VZ 1,2,3 01 7.0 8.6 V Input Open Circuit Voltage VINOC1,2,3 01 4.0 4.6 V BG Regulator Output Voltage VBG1 01 1.990 2.010 V 2,3 1.980 2.020 BG Regulato

39、r Load Regulation IBGIBG= 0 to 2 mA 1,2,3 01 -5 +5 mV Internal Output Pull-Up Resistor RINT 1,2,3 01 8 12 k Comparator Pulse Delay Low to High tDLH C1 = 37 pF, VEN= VENH, VREF= 1 V, ISINK= 0, See figure 4 2/ 9,10,11 01 0.2 10 s Comparator Pulse Delay High to Low tDHL9,10,11 01 80 150 ns Enable Delay

40、 to VOUTtEDVLH C1 = 37 pF, VIN= 2.0 V, VREF= 1 V, ISINK= 0, See figure 4 2/ 9,10,11 01 100 1500 ns tEDVHL 500 3000 Enable Delay to IOUTtEDILH C1 = 68 pF, ISINK= 0, See figure 4 2/ 9,10,11 01 100 250 ns tEDIHL 100 250 Supply Current Disabled Enabled ICCD ICCE1,2,3 01 4.0 7.0 mA mA 1/ Guaranteed by de

41、sign, but not tested. 2/ Test fixture node capacitance plus 10 pF scope capacitance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEE

42、T 6 DSCC FORM 2234 APR 97 Symbol Inches Millimeters Min Max Min Max A .125 3.18 A1 .046 .056 1.17 1.42 b .012 .018 .30 .46 c .009 .011 .23 .28 D/E .630 16.00 e .050 BSC 1.27 BSC e1 .400 10.16 L .200 5.08 R .015 .025 .38 .64 NOTES: 1. The U.S. preferred system of measurement is the metric SI. This it

43、em was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD

44、MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 VCCIOUT/VIN_1 IOUT/VIN_2 IOUT/VIN_3 IOUT/VIN_4 IOUT/VIN_5

45、CASE_GND (see note) ENABLE GND GND BG REG OUT COMPREF VOUT_5VOUT_4 VOUT_3VOUT_2VOUT_1VCC NOTE: CASE_GND (Pin 7) should be grounded to eliminate or minimize electrostatic discharge (ESD) or static buildup. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking perm

46、itted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Schematic diagram. OUT GND 9, 10 PRECISION 2 VOLT REFERENCE 10 k 10 k 10 k 10 k 10 k I=80 A I=80 A I=80 A I=80 A

47、 + - 1,18 V CC + - I / V OUT IN_1 17 12 V OUT_1 COMP_REF 16 V OUT_2 I / V OUT IN_2 + - 15 V OUT_3 I / V OUT IN_3 + - 14 V OUT_4 I / V OUT IN_4 + - 13 V OUT_5 I / V OUT IN_5 6 5 4 3 2 I=80 A 8 ENABLE 11 BG Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

48、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIGURE 4. Timing diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09234 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 TABLE II. Electrical test req