DLA MS51822 REV E-1987 TEE PIPE TO TUBE FEMALE PIPE ON RUN FLARELESS TYPE HYDRAULIC [Refer To SAE J514 SAE J514 SAE J514 SAE J514 SAE J514]《液压非扩口式管子承头三岔管》.pdf

《DLA MS51822 REV E-1987 TEE PIPE TO TUBE FEMALE PIPE ON RUN FLARELESS TYPE HYDRAULIC [Refer To SAE J514 SAE J514 SAE J514 SAE J514 SAE J514]《液压非扩口式管子承头三岔管》.pdf》由会员分享，可在线阅读，更多相关《DLA MS51822 REV E-1987 TEE PIPE TO TUBE FEMALE PIPE ON RUN FLARELESS TYPE HYDRAULIC [Refer To SAE J514 SAE J514 SAE J514 SAE J514 SAE J514]《液压非扩口式管子承头三岔管》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、LfUUT-MS51823 SLEEVE -MC51825 DASH NUMBER A B D M1 N1 s2 Y1 O.D. PIPE STRAIGHT THREAD DIA THREAD CLASS 2A DRILL -1 1;: NPTF f.03 +.O3 MIN f.020 TABLE I 1 2 21 U8 1/8 5/16-24UNF 0.093 0.83 0.66 0.75 0.562 22 3/16 1/8 3/8 -24UNF 0.125 0.83 0.66 0.76 0.562 3 23 I 1/4 I 1/8 I 7/16-20UNF 1 0.203 I 0.89 I

2、 0.66 I 0.80 I 0.562 I L I I 5 25 I 3/8 I 1/4 I 9/16-18UNF I 0.281 I 1.05 I 0.88 I 1.06 I 0.750 4 6 I 26 I 1/2 I 3/8 I 3/4 -16UNF I 0.422 I 1 .23 I 1.02 I 1.27 I 0.875 24 I 5/16 1 U8 I 1/2 -2UUNF I 0.234 I 0.95 I 0.66 I 0.82 I 0.562 7 0.718 1-5/16-12UN 0.875 1 .O93 12 1.344 13 33 2-1/2 -12UN 1.813 2

3、7 7/8 -14UNF 0.500 1.42 1.23 1.52 1.062 1.62 3.34 2.812 1.42 1.82 1.312 FOR NOTES SEE SHEET 2. ROCUREUENT SPECIFICATION WPERSEDES. CN13 in part and 13.1 in part MIL-F-18866 Benotes change SHEET 1 OF 2 71TLE TEE, PIPE TO TUBE, FEMALE PIPE ON RUN, FLARELESS TYPE, HY DRAW C MILITARY ST A# DARD bm- Prov

4、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS5l1822 REV E L17 7779732 OOLLOZ7 b W I f ED. SUP. CLASS NOTES: I 4730 1. MATERIAL: Steel, carbon in accordance with procurement specification. 2. PROTECTIVE COATING: Cadmium plated in accordance with proc

5、urement specification. Steel, corrosion-resisting in accordance with procurement specification. Zinc plated in accordance with procurement specification. Phosphate coating in accordance-with procurement specification. Passivation treatment in accordance with procurement specification. 3. DIMENSIONS

6、AND TOLERANCES: Dimensions and tolerances not shown shall be.in accordance with the SAE Standard for Flareless Tube Fittings (SAE 5514). 4. THREADS: Threads shall be in accordance with Screw-Thread Standards for Federal Services, FED-CTD-HZ8. 5. PART NkiBER: 6. For ence ,sign fea herein. The MS part

7、 number consists of the MS number, plus the dash number and (for complete assembly) the applicable MS51825 sleeve style designator. A. For the complete assembly (with nuts and sleeves), cadmium plated, use the MS number, plus the assembly dash number and the sleeve style designator. Example: MS51822

8、-1A or MS51822-1B. For the body only, cadmium plated, use the MS number and the body dash number. Example: MS51822-21. For zinc coating add “2“ and (for complete assembly) the sleeve style designator to the dash number. Example: MS51822-IZA or MS51822-1ZB or B. C. MS51822-21Z. D. For phosphate coati

9、ng add Pi and (for complete assembly) the sleeve style designator to the dash number. Example: MS51822-1PA or MS51822-1PB or MS51822-21P. For corrosion-resisting steel add “SS“ and (for complete assembly) the sleeve style designator to the dash number. Example: MS51822-1SSA or MS51822-1SSB or MS5182

10、2-21SS. E. ire purposes, this standard takes precedence over procurement documents refer- 7. 8. * 9. Reference documents shall be of the issue in effect on date of invitations for bid. The illustration is for identification and is not intended to restrict designs or shapes not dimensioned. After 22

11、NOV 1974 for maintenance. , bodies will be used for roduction only and SHALL NOT be stocked Existing stock of bodies should te used until depleted. 10. CAUTION: MS51822 will replace MC39209 for new design after approval date on this document. Table II below gives reference data for coordination of e

12、quivalent tube sizes, in both compresiion and hydraulic type tees. The following data is rurnished for the purpose of new design only and is not in- tended to imply interchangeability. Assembly replacement is authorized. TABLE II (FOR INFORMATION ONLY) ASSEMBLY EQUIVALENCY -12 I -12 -* I -* I O m M

13、Il IT ARY ST AN DA RD .A. AR TITLE ihw Cui, 99 TEE, PIPE TO TUBE HYDRAULIC MS51822 FEMALE PIPE ON RU,RARELESS TYPE, RKUREMENT SPECIFICATION SUPERSEDE): C“x13 in part and 13.1 in part SHEET 2 W 2 MIL-F-18866 DO tEt7 672-1 (Coordinated) cnavioui aoiriou or rwi vow An1 OBIOLITI. 4730-0888 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-