DLA MS27291 REV G-2009 SUPPORT CABLE ELECTRICAL CONNECTOR [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1) DLA MIL-DTL-83723F SUPP 1A DLA MIL-DTL-83723F S.pdf

《DLA MS27291 REV G-2009 SUPPORT CABLE ELECTRICAL CONNECTOR [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1) DLA MIL-DTL-83723F SUPP 1A DLA MIL-DTL-83723F S.pdf》由会员分享，可在线阅读，更多相关《DLA MS27291 REV G-2009 SUPPORT CABLE ELECTRICAL CONNECTOR [Use DLA MIL-DTL-83723 G SUPP 1 DLA MIL-DTL-83723 G DLA MIL-DTL-83723F (1) DLA MIL-DTL-83723F SUPP 1A DLA MIL-DTL-83723F S.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 DETAIL SPECIFICATION SHEET SUPPORT, CABLE, ELECTRICAL CONNECTOR This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-26500. FIGURE 1. Dim

2、ensions and configurations. AMSC N/A FSC 5935 INCH-POUND MS27291G 20 August 2009 SUPERSEDING MS27291F 6 February 2004 Inches mm .032 .812 .042 1.067 .250 6.35 .262 6.65 .360 9.14 .365 9.27 .420 10.67 .450 11.43 Inactive for new design after 14 November 1977. For new design, use MIL-DTL-83723, series

3、 III, which is interchangeable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27291G 2 MS PIN For use with connector class Shell size A max dia B dia .005 MS27291-1 MS27291-101 MS27291-2 MS27291-201 MS27291-3 MS27291-301 MS27291-4 MS27291-401 MS2

4、7291-5 MS27291-501 MS27291-6 MS27291-601 MS27291-13 MS27291-701 MS27291-14 MS27291-801 MS27291-15 MS27291-901 R, F G R, F G R, F G R, F G R, F G R, F G R, F G R, F G R, F G 10 10 12 12 14 14 16 16 18 18 22 22 8 8 20 20 24 24 .731 .731 .919 .919 .981 .981 1.106 1.106 1.231 1.231 1.481 1.481 .606 .606

5、 1.356 1.356 1.606 1.606 .459 .459 .636 .636 .698 .698 .823 .823 .941 .941 1.191 1.191 .334 .334 1.066 1.066 1.316 1.316 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27291G 3 MS PIN For use with

6、 connector class Shell size “C” Nom UNEF-2B thread D .015 E dia .015 F max G dia max. MS27291-1 MS27291-101 MS27291-2 MS27291-201 MS27291-3 MS27291-301 MS27291-4 MS27291-401 MS27291-5 MS27291-501 MS27291-6 MS27291-601 MS27291-13 MS27291-701 MS27291-14 MS27291-801 MS27291-15 MS27291-901 R, F G R, F G

7、 R, F G R, F G R, F G R, F G R, F G R, F G R, F G 10 10 12 12 14 14 16 16 18 18 22 22 8 8 20 20 24 24 .5625-24 .5625-24 .750 .750 .8125 .8125 .9375 .9375 1.0625 1.0625 1.3125 1.3125 .4375 .4375 1.1875 1.1875 1.4375 1.4375 .935 .935 .935 .935 1.170 1.170 1.170 1.170 1.170 1.170 1.170 1.170 .935 .935

8、1.170 1.170 1.170 1.170 .270 .270 .400 .400 .460 .460 .610 .610 .690 .690 .940 .940 .186 .186 .816 .816 1.066 1.066 .914 .914 1.026 1.026 1.090 1.090 1.250 1.250 1.358 1.358 1.604 1.604 .789 .789 1.481 1.481 1.729 1.729 .435 .435 .565 .565 .625 .625 .775 .775 .855 .855 1.105 1.105 .351 .351 .981 .98

9、1 1.231 1.231 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27291G 4 MS PIN For use with connector class Shell size A max dia. B dia .005 “C” -36NS2A thread MS27291-702 MS27291-102 MS27291-202 MS

10、27291-302 MS27291-402 MS27291-502 MS27291-802 MS27291-602 MS27292-902 E E E E E E E E E 08 10 12 14 16 18 20 22 24 .606 .731 .919 .981 1.106 1.231 1.356 1.481 1.606 .334 .459 .631 .698 .823 .941 1.066 1.191 1.316 .4340 .5634 .7334 .8032 .9302 1.0362 1.1611 1.2862 1.1111 MS PIN For use with class con

11、nector Shell size D .015 E dia. .015 F max G dia max MS27291-702 MS27291-102 MS27291-202 MS27291-302 MS27291-402 MS27291-502 MS27291-802 MS27291-602 MS27292-902 E E E E E E E E E 08 10 12 14 16 18 20 22 24 .935 .935 .935 1.170 1.170 1.170 1.170 1.170 1.170 .186 .270 .400 .460 .610 .690 .816 .940 1.0

12、66 .769 .914 1.026 1.090 1.250 1.358 1.481 1.604 1.729 .351 .435 .565 .625 .775 .855 .981 1.105 1.231 FIGURE 1. Dimensions and configurations Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27291G 5 Inches mm Inches mm Inches mm .032 .08

13、1 .61 15.49 1.026 26.06 .042 1.07 .625 15.87 1.0362 26.32 .186 4.72 .636 16.15 1.0625 26.99 .25 6.35 .69 17.53 1.066 27.07 .262 6.65 .698 17.73 1.09 27.69 .27 6.85 .731 18.57 1.105 28.06 .334 8.48 .7334 18.63 1.106 28.09 .351 8.91 .75 19.05 1.1111 28.22 .36 9.14 .775 19.68 1.1611 29.49 .365 9.27 .78

14、9 20.04 1.17 29.72 .4 10.16 .8032 20.4 1.875 30.16 .42 10.67 .8125 20.64 1.191 30.25 .434 11.02 .823 20.9 1.231 31.27 .435 11.05 .855 19.68 1.25 31.75 .4375 11.11 .914 23.21 1.2862 32.67 .45 11.43 .919 23.34 1.3125 33.33 .459 11.66 .9302 23.63 1.356 34.44 .46 11.68 .935 23.75 1.358 34.49 .5634 14.31

15、 .94 23.87 1.481 37.62 .565 14.35 .941 23.9 1.604 40.74 .606 15.39 .981 24.92 1.606 40.79 1.729 43.29 NOTES: 1. Dimensions are in inches. Metric equivalent are given for information only. 2. Unless otherwise specified, tolerances are .005 for three place decimals and .02 for two place decimals. 3. A

16、ll threads are in accordance with FED-STD-H28. 4. Remove all burrs and sharp edges. FIGURE 1. Dimensions and configurations Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27291G 6 REQUIREMENTS Dimensions and configurations: See figure 1.

17、 Materials: Cable strap; aluminum alloy in accordance with SAE-AMS-QQ-A-367 or ASTM-B209 or stainless steel type, 300 or 216 series. Cable strap for use with class R and F connectors. For aluminum alloy, anodize in accordance with MIL-A-8625 or suitable hard anodizing process to meet the performance

18、 requirements of MIL-DTL-26500 and MIL-DTL-83723. For stainless steel the finish shall be black oxide or equivalent. Cable strap for use with class G connectors; for stainless steel, chromium plating in accordance with SAE-AMS-QQ-C-320, class 2a, type II, .0002 minimum thickness. Cable support; alum

19、inum alloy in accordance with ASTM-B85/B85M composition 13, A13, A380, or 380. Cable support use with class R and F connectors; for aluminum alloy, in accordance with MIL-A-8625 or suitable hard anodizing process to meet the performance requirements of MIL-DTL-26500 and MIL-DTL-83723. Cable support

20、for use with class G connectors; for aluminum alloy, chromium plating in accordance with SAE-AMS-QQ-C-320, class 2a, type II, .0002 minimum thickness. Part or Identifying Number (PIN): MS27291-1. Changes from previous issue. Marginal notations are not used in this revision to identify changes with r

21、espect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-26500, this document references the following: MIL-A-8625 MIL-DTL-83723 FED-STD-H28 SAE-AMS-QQ-C-320 SAE-AMS-QQ-A-367 NASM35275 NASM35338 ASTM-B85/B85M ASTM-B209 Provided by IHSNot for ResaleN

22、o reproduction or networking permitted without license from IHS-,-,-MS27291G 7 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA - CC DLA - CC (Project 5935-2009-122) Review activities: Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-