DLA MS25457 REV H-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I MAGNETIC LATCH SOCKET MOUNTED HERMETICALLY SEALED《I型2 PDT 10安培火箭安装磁力锁密封电磁继电器》.pdf

《DLA MS25457 REV H-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I MAGNETIC LATCH SOCKET MOUNTED HERMETICALLY SEALED《I型2 PDT 10安培火箭安装磁力锁密封电磁继电器》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25457 REV H-2003 RELAYS ELECTROMAGNETIC 10 AMPERES 2 PDT TYPE I MAGNETIC LATCH SOCKET MOUNTED HERMETICALLY SEALED《I型2 PDT 10安培火箭安装磁力锁密封电磁继电器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AMSC N/A 1 of 5 FSC 5945 INCH-POUND MS25457H 27 November 2003 SUPERSEDING MS25457G 20 January 1989 DETAIL SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, 10 AMPERES, 2 PDT, TYPE I, MAGNETIC LATCH, SOCKET MOUNTED, HERMETICALLY SEALED INACTIVE FOR NEW DESIGN AFTER 5 JUNE 1987. NO SUPERSEDING SPECIFICATI

2、ON. (FOR NEW DESIGN USE MIL-PRF-83536/12, MIL-PRF-83536/13, MIL-PRF-83536/14) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL

3、-PRF-6106. FIGURE 1. Dimensions and configurations. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25457H 2 Inches mm Inches mm .001 0.03 .203 5.16 .005 0.13 .293 7.74 .040 1.02 .344 8.74 .047 1.19 .435 11.05 .062 1.57 .580 14.73 .0625 1.59 1.031

4、26.19 .093 2.36 1.500 38.10 .145 3.68 1.812 46.02 .147 3.73 1.844 46.84 .157 3.99 2.187 55.55 NOTES: 1/ Dimensions are in inches. 2/ Metric equivalents are given for general information only. 3/ Unless otherwise specified, tolerance is .010 (0.25 mm). 4/ Relay is magnetically latched in both positio

5、ns. Caution note to observe polarity must appear on relays with dc coils. 5/ Terminal numbers need not appear on relay headers provided there is affixed to the relay a suitable legible circuit diagram that permanently and positively identifies each terminal location specified hereon. 6/ The use of d

6、iodes on ac relays is optional. Actual application must be shown on label. 7/ Shock, vibration, and acceleration requirements application with coils de-energized. 8/ In the event of conflict between the text of this specification and the references cited herein, the text of this specification shall

7、take precedence. 9/ Referenced Government documents of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation forms a part of this specification to the extent specified herein. 10/ Socket pin terminals shall provide th

8、e operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated contacts. Terminals shall be gold plated. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplate of 50 to 150 microinches thick. The gold plat

9、ing system shall enable the product to meet the performance requirements of this specification and shall be approved by the qualifying activity. 11/ Gasket shall provide a reliable seal between the relay and mating socket that will meet the environmental, operational, and interface requirements of t

10、he relay with the mating socket. The gasket shall have thickness .075, recessed .047 in to bracket. Gasket material according to AMS 3332 has been considered acceptable. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without

11、license from IHS-,-,-MS25457H 3 TABLE I. Dash numbers and characteristics. Dash number MS25457- Type Coil Terminal type Max weight in pounds D1 I dc Plug in 0.30 A1 I ac Plug in 0.32 AD1 I ac-dc Plug in 0.32 TABLE II. Operating characteristics. Coil data Time - milliseconds max Rated Max Max pick-up

12、 voltage Contact Bounce Main AuxPIN MS25457- Coil Volts 1/ Freq Hz Res Volts Amp Nor- mal 2/ High temptest Cont cur-rent test Drop out vol-tage Op-erate 3/ Rel-ease 4/ NO NC NO NC D1 X1, X2 Y1, Y2 28 dc N/A 29 0.17 18 18 19.8 N/A 25 N/A 2 2 N/A N/A A1 X1, X2 Y1, Y2 115 400 5/ N/A 122 0.07 90 90 95 N

13、/A 25 N/A 2 2 N/A N/A X1, X2 115 400 5/ N/A 122 0.07 90 90 95 N/A 25 N/A 2 2 N/A N/A AD1 Y1, Y2 28 dc N/A 29 0.17 18 18 19.8 N/1 25 N/A 2 2 N/A N/A 1/ CAUTION: Use of any coil voltage less than rated voltage will compromise the operation of the relay. 2/ Over the temperature range. 3/ With rated coi

14、l voltage. 4/ From rated coil voltage. 5/ MS25457-A1 and AD1 may be used on 60 Hz if maximum ambient temperature is +85C (maximum coil current shall be 0.077 ampere). TABLE III. Rated contact load (amperes per pole) (case grounded). 28 V dc 115 V ac, 1 phase 115/200 V ac, 3 phase 1/ Main Aux Main Au

15、x Main Aux Type of load Life operating cycles x 103NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz See appropriate notes Resistive 100 10 10 10 6 10 6 Inductive 100 Inductive 20 6 6 10 4 10 4 Motor 100 4 4 4 3 4 3 Lamp 100 2 2 2 1.5 2 1.5 Transfer load 2/ Mechanical life reduced curr

16、ent 400 2.5 2.5 2.5 2 2.5 2 Mixed loads Applicable per specification 1/ Absence of value indicates relay is not rated for 3-phase application. 2/ Transfer load indicates relay is suitable for transfer between unsynchronized ac power supplies at rating indicated. Provided by IHSNot for ResaleNo repro

17、duction or networking permitted without license from IHS-,-,-MS25457H 4 Environmental characteristics. Temperature range -70C to +125C Max altitude rating 80,000 ft Shock G-level 50 gs Duration 11 ms Max duration contact opening 10 s Vibration - sinusoidal G-level 10 gs Frequency range 5 - 1,500 Hz

18、Acceleration 15 gs Electrical characteristics. Insulation resistance, initial 100 megohms. After life or environmental tests 50 megohms. Dielectric strength (sea level). Initial After life tests Coil to case 1,000 V rms 1,000 V rms Aux contacts All other points 1,500 V rms 1,125 V rms Dielectric str

19、ength (altitude). (When mounted in mating socket) 80,000 ft Coil to case 500 V rms Aux contacts All other points 500 V rms Max contact drop initial 0.150 volt. After life test 0.175 volt. Overload current 40 amperes dc, 60 amperes ac. Rupture current 50 amperes dc, 80 amperes ac. Duty rating Continu

20、ous. RFI specification MIL-STD-461. (Applicable to coil circuits of ac operated relays.) Conformance inspection. Group A acceptance reports shall be submitted to the preparing activity on a yearly basis in order to retain qualification for this military specification sheet. Performance of groups B a

21、nd C tests are not applicable. Qualification by similarity: See MIL-PRF-6106. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25457H 5 NOTES Referenced documents. In addition to MIL-PRF-6106, this specification sheet references the following docume

22、nts. (Government documents are available on line at http:/assist.daps.dla.mil/quicksearch or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094). Society of Automotive Engineers documents are available from the Society of

23、 Automotive Engineers 400 Commonwealth Drive Warrendale, Pennsylvania, United States, 15096-0001. http:/www.sae.org STANDARDS Department of Defense MIL-STD-461 - Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment Society of Automotive Engineers (

24、SAE) SAE-AMS3332 - Silicone Rubber Extreme Low-Temperature Resistant, 15-30 Custodians: Preparing activity:Navy - AS DLA - CC Air Force - 11 DLA - CC (Project 5945-1221-12) Review activities: Navy - EC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using ASSIST Online database at www.dodssp.daps.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-