DLA MIL-DTL-6001 B-2013 FITTINGS AIRCRAFT SOLDER TYPE TUBE.pdf

《DLA MIL-DTL-6001 B-2013 FITTINGS AIRCRAFT SOLDER TYPE TUBE.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-6001 B-2013 FITTINGS AIRCRAFT SOLDER TYPE TUBE.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 4730 MIL-DTL-6001B 13 February 2013 SUPERSEDING MIL-F-6001A (ASG) 15 July 1958 DETAIL SPECIFICATION FITTINGS; AIRCRAFT, SOLDER TYPE, TUBE This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers th

2、e general requirements for fittings, aircraft, solder type, tube. 1.2 Part or Identifying Number (PIN). The PIN requirements are shown in the specification sheets. 1.2.1 Air Force Navy Aeronautical Standard. The specification sheets are listed in supplement 1. 1.2.2 Size of fittings. Sizes are shown

3、 in the individual specification sheets. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional informatio

4、n or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifi

5、cations, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. FEDERAL SPECIFICATIONS QQ-N-281 Nickel-Cop

6、per-Alloy (Monel and R-Monel) Bars, Plates, Rods, Sheets, Strips, Wire, Forgings, and Structural and Special Shaped Sections Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI, P.O. Box 3990, Columbus, OH 43218-3990, or emailed to FluidFlowd

7、la.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. INCH-POUNDInactive for new design after 24 July 1998. Provided by IHSNot for ResaleNo reproduction or networking permitted without

8、license from IHS-,-,-MIL-DTL-6001B 2 DEPARTMENT OF DEFENSE SPECIFICATIONS (See supplement 1 for list of specification sheets.) DEPARTMENT OF DEFENSE STANDARD MIL-STD-129 Marking for Shipment and Storage (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the

9、 Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of documents are those cited in the solici

10、tation or contract. ASTM INTERNATIONAL ASTM B121/B121M Leaded Brass Plate, Sheet, Strip, and Rolled Bar, Standard Specification for ASTM B154 Mercurous Nitrate Test for Copper Alloys, Standard Test Method for ASTM B858 Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in

11、 Copper Alloys, Standard Test Method for (Copies of these documents are available online at http:/www.astm.org or from the ASTM International, P.O. Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) INTERNATIONAL ORGANIZATION FOR STANDARDIZATION (ISO) ISO 6957 Copper Alloys - Ammoni

12、a Test for Stress Corrosion Resistance First Edition ISO 17025 General requirements for the competence of testing and calibration laboratories ISO 19879 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections - Second Edition (Copies of these docu

13、ments are available online at www.ansi.org or from the ANSI Customer Service Department, 25 W. 43rdStreet, 4thFloor, New York, NY 10036.) NCSL INTERNATIONAL NCSL Z540.3 Requirements for the Calibration of Measuring and Test Equipment (Copies of these documents are available online at http:/www.ncsli

14、.org or from NCSL International 2995 Wilderness Place, Suite 107 Boulder, Colorado 80301-5404) SAE INTERNATIONAL SAE AMS-QQ-P-416 Plating, Cadmium (Electrodeposited) SAE AMS2700 Passivation of Corrosion Resistant Steels SAE AMS-S-7720 Steel, Corrosion-Resistant (18-8) Bars, Wire and Forging Stock (A

15、ircraft Quality) (Copies of these documents are available on line at www.sae.org from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, and Tel: 877-606-7323 inside USA and Canada or 724-776-4970 outside USA, email at CustomerServicesae.org.) Provided by IHSNot for ResaleNo repro

16、duction or networking permitted without license from IHS-,-,-MIL-DTL-6001B 3 2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between this document and the references cited herein (except for related specification sheets) the text of this document

17、 takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Specification sheets. The individual item requirements shall be as specified herein and in accordance with the applicable specification

18、sheet. In the event of any conflict between the requirements of this specification and the specification sheet, the latter shall govern. 3.2 First article. When specified (see 6.2), samples shall be subjected to first article inspection in accordance with 4.4. 3.3 Design and dimensions. The design a

19、nd dimensions shall meet the requirements specified herein and in the applicable AN or MS standard. 3.4 Shape and form restrictions. Abrupt reductions of section shall be avoided. Small external sections adjoining relatively heavy body sections shall be shaded into the heavier sections by means of a

20、mple fillets. Sharp corners or inadequate fillets, excessive undercuts or grooves, at the junction of such small sections with large sections of fittings shall be considered cause for rejection. Unless otherwise specified, drawing tolerances shall apply to fillet and corner radii. 3.5 Materials. Fit

21、tings shall be fabricated of materials listed in table I as specified on the applicable AN or MS standard. TABLE I. Materials. Materials Form Specification Number Brass Bars, Rods, Shapes and Forging ASTM B121/B121M Corrosion Resistant Steel (18Cr 8Ni) Bars and Rods SAE AMS-S-7720 Nickel Copper - Al

22、loy Forging, Plates, Rods, Shapes, Sheets, Strips and Wire QQ-N-281 3.5.1 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible, provided that the material meets or exceeds the operatio

23、nal and maintenance requirements, and promotes economically advantageous life cycle cost. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-6001B 4 3.6 Finish. 3.6.1 Brass cadmium plating. Cadmium plating, when required, shall be in accordance

24、with SAE AMS-QQ-P-416. 3.6.2 Corrosion resistant steel. Corrosion resistant steel shall be passivated in accordance with SAE AMS2700, method 2. 3.6.3 Nickel copper alloy. No additional finish required. 3.7 Performance. 3.7.1 Examination of product. The fittings shall conform to the requirements of t

25、his specification and the applicable AN or MS standard when visually examined as specified in 4.7.1. 3.7.1.1 Cleanliness. Fittings shall be free of all foreign materials, both internally and externally, which could adversely affect performance and reliability when examined as specified in 4.7.1.1. 3

26、.7.1.2 Dimensions. Fittings shall be within the tolerances specified herein and on the applicable AN or MS standard when examined as specified in 4.7.1.2. 3.7.2 Drill offset. On straight fittings where the fluid passage is drilled from each end, the offset between the drilled holes at the meeting po

27、int of the drills shall not exceed 0.015 inch (see 4.7.2). 3.7.3 Angle fittings. On angle fittings, the cross-sectional area at the junction of the fluid passages shall not be smaller than the cross-sectional area of the smaller passage (see 4.7.3). 3.7.4 Wall thickness. Except as otherwise specifie

28、d on the applicable AN or MS standard, the wall thickness at any point on the fitting shall be not less than the thickness established by the dimensions and tolerances for the inside and outside diameters and eccentricities specified in the AN or MS standard (see 4.7.4). 3.7.5 Leakage test. The fitt

29、ings shall withstand the leakage pressure specified in table II without malfunction or leakage, when tested in accordance with 4.7.5. 3.7.6 Proof pressure. The fittings shall withstand the proof pressure specified in table II without malfunction or leakage, when tested in accordance with 4.7.6. 3.7.

30、7 Vibration test. The fittings shall not leak, rupture, or fail at the working pressure specified in table II, when tested in accordance with 4.7.7. 3.7.8 Internal strain of copper base alloys. Fittings made of copper base alloys (ASTM B121/B121M) shall have no internal strains as revealed by the te

31、st specified in 4.7.8. 3.8 Identification of product. All fittings shall be marked in accordance with the following instructions. The marking shall be applied in a location not detrimental to the fitting and shall not be detrimental to the corrosion protection of the fitting. 3.8.1 AN or MS symbols

32、and trademarks. Unless otherwise specified, all fittings shall be marked with the letters AN or MS and the manufacturers name or trademark. The marking shall be permanent, preferably embossed letters or impression stamping. However, ink stamping may be used. The letters AN or MS shall be separated a

33、nd distinct from the manufacturers name or trademark. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-6001B 5 3.8.2 Identifying number or letter. Wherever practicable, each fitting shall also be identified by the complete AN or MS standard nu

34、mber as shown by the AN or MS standard. The size and material code letter is not to be included with the standard number. The identifying number shall be added to the part by embossing, impressing stamping, ink stamping, or printed on a paper collar supplied with the fitting. The preferable marking

35、shall be in the order mentioned. The identifying number shall not be placed on the union nut specified in AN805. Also the fittings in sizes -6 and under need not be individually marked but shall be packaged in units, with the package carrying the identifying number. 3.9 Workmanship. Fittings shall b

36、e free from burrs and longitudinal and spiral tool marks. All sealing surfaces shall be smooth except that annular tool marks up to 100 microinches rms maximum will be acceptable. Workmanship shall conform to the best commercial practice to produce fittings free from all defects which will affect pr

37、oper functioning in service. TABLE II. Performance requirements. Fitting dash size Maximum working pressure Minimum leakage pressure Minimum proof pressure psi MPa psi MPa psi MPa 2 100 .689 200 1.38 200 1.38 3 100 .689 200 1.38 200 1.38 4 100 .689 200 1.38 200 1.38 5 100 .689 200 1.38 200 1.38 6 10

38、0 .689 200 1.38 200 1.38 8 100 .689 200 1.38 200 1.38 10 100 .689 200 1.38 200 1.38 12 100 .689 200 1.38 200 1.38 16 100 .689 200 1.38 200 1.38 4. VERIFICATION 4.1 Classification of inspection. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4

39、.4). b. Conformance inspection (see 4.5). 4.2 Test equipment and inspection facilities. Test and measuring equipment and inspection facilities of sufficient accuracy, quality and quantity to permit performance of the required inspection shall be used. The establishment and the maintenance of a calib

40、ration system to control the accuracy of all test and measuring equipment shall be in accordance with ISO 17025 and NCSL Z540.3, as applicable. 4.3 Inspection conditions. Unless otherwise specified, tests and inspections shall be conducted at local ambient temperature and barometric pressure. 4.4 Fi

41、rst article inspection. First article inspection shall be performed at a laboratory acceptable to the Government on sample units produced with equipment and procedures used in production. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-6001B

42、6 4.4.1 Samples for first article. Unless otherwise specified, after award of the contract or order, the manufacturer shall forward three fittings selected at random. The samples shall be representative of the products proposed to be furnished to this specification. When a manufacturer is in continu

43、ous production of the fittings from one contract to another or has demonstrated within the past 2 years the capability to meet the requirements of this specification, inspection of additional first article samples for a new contract may be waived at the discretion of the acquiring activity (see 6.3)

44、. Approval of the first article samples or the waiving of first article inspection does not preclude the requirements for performing conformance inspection. First article samples shall be furnished to the Government as directed by the contracting officer (see 6.3). 4.4.2 Inspection routine. The samp

45、le(s) shall be subjected to the first article inspections specified in table III and in the specified sequence. 4.4.3 Failures. One or more failures shall be cause for refusal to grant first article approval. TABLE III. First article inspections. Inspection Requirement paragraph Test method paragrap

46、h Examination of product 3.7.1 4.7.1 Cleanliness 3.7.1.1 4.7.1.1Dimensions 3.7.1.2 4.7.1.2 Drill offset 3.7.2 4.7.2Angle fittings 3.7.3 4.7.3 Wall thickness 3.7.4 4.7.4Leakage test 3.7.5 4.7.5 Proof pressure 3.7.6 4.7.6Vibration test 3.7.7 4.7.7 Internal strain of copper base alloys 1/ 2/ 3.7.8 4.7.

47、81/ This is a destructive test. 2/ This test shall be performed when specified by the acquiring activity (see 6.3). 4.5 Conformance inspection. 4.5.1 Inspection of product for delivery. Inspection of product for delivery shall consist of individual inspections in table IV. TABLE IV. Individual inspe

48、ction. Inspection Requirement Paragraph Test method paragraph Examination of product 3.7.1 4.7.1 Cleanliness 3.7.1.1 4.7.1.1 Dimensions 3.7.1.2 4.7.1.2 Leakage test 3.7.5 4.7.5 Proof pressure 3.7.6 4.7.6 4.5.2 Sampling for individual inspections. Fittings for sampling shall be selected from a produc

49、tion lot (see 4.5.2.1) and shall be subjected to the individual inspections. The sampling size shall be as specified in 4.5.2.2. 4.5.2.1 Production lot. A production lot shall consist of all fittings of the same PIN which have been manufactured under the same conditions and on the same continuous run. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-