DLA MIL-DTL-3970 13 E-2013 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE BEND.pdf

《DLA MIL-DTL-3970 13 E-2013 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE BEND.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3970 13 E-2013 WAVEGUIDE ASSEMBLIES RIGID 90-DEGREE H-PLANE BEND.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985 MIL-DTL-3970/13E 3 December 2013 SUPERSEDING MIL-DTL-3970/13D 3 February 2009 DETAIL SPECIFICATION SHEET WAVEGUIDE ASSEMBLIES, RIGID, 90-DEGREE H-PLANE BEND This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acq

2、uiring the waveguide assemblies described herein shall consist of this specification sheet and MIL-DTL-3970. FIGURE 1. Assembly configuration. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3970/13E 2 TABLE I. Dash number, electri

3、cal and physical characteristics, and dimensions. Flange Frequency Insertion Pressur- Dimensions 1/ 2/ 3/ Dash Wave- 1 2 range loss VSWR ization no. guide M85/ M3922/ TE10mode GHz max dB max lbf/in2gage A B nom C D R 001 1-043 56-001 61-002 2.6 - 3.95 - 1.05 15 10.500 (266.70) .030 (0.76) 1.500 (38.

4、10) .115 (2.92) .012 (0.30) 7.500 (190.50) .125 (3.18) 002 1-055 57-002 62-002 3.95 - 5.85 - 1.05 30 7.000 (177.80) .030 (0.76) 1.000 (25.40) .077 (1.96) .008 (0.20) 5.000 (127.00) .125 (3.18) 003 1-067 55-001 60-001 5.85 - 8.20 - 1.03 30 4.875 (123.83) .025 (0.64) .750 (19.05) .056 (1.42) .006 (0.1

5、5) 3.375 (85.72) .125 (3.18) 004 1-073 53-002 59-007 7.05 - 10.0 - 1.07 30 4.062 (103.17) .020 (0.51) .687 (17.45) .044 (1.12) .005 (0.13) 2.750 (69.85) .063 (1.60) 005 1-079 53-001 59-006 8.20 - 12.4 - 1.05 30 3.562 (90.47) .020 (0.51) .562 (14.27) .038 (0.97) .004 (0.10) 2.500 (63.50) .063 (1.60)

6、008 1-077 53-003 59-008 8.2 - 12.4 - 1.05 30 3.562 (90.47) .015 (0.38) .562 (14.27) .038 (0.97) .004 (0.10) 2.500 (63.50) .063 (1.60) 009 1-071 53-004 59-009 7.05 - 10.0 - 1.07 30 4.062 (103.17) .020 (0.51) .687 (17.45) .044 (1.12) .005 (0.13) 2.750 (69.85) .063 (1.60) 010 1-041 56-002 61-001 2.60 -

7、 3.95 - 1.05 15 10.500 (266.70) .030 (0.76) 1.500 (38.10) .115 (2.92) .012 (0.30) 7.500 (190.50) .125 (3.18) 011 1-089 53-005 59-001 12.4 - 18.0 .07 1.04 30 2.601 (66.07) .015 (0.38) .500 (12.70) .028 (0.71) .003 (0.08) 1.750 (44.45) .063 (1.60) 012 1-053 57-001 62-001 3.95 - 5.85 - 1.05 30 7.000 (1

8、77.80) .030 (0.76) 1.000 (25.40) .076 (1.93) .008 (0.20) 5.000 (127.00) .125 (3.18) 014 1-065 55-002 60-002 5.85 - 8.20 - 1.03 30 4.875 (123.82) .025 (0.64) .750 (19.05) .056 (1.42) .006 (0.15) 3.375 (85.72) .125 (3.18) See footnotes at end of table I. Provided by IHSNot for ResaleNo reproduction or

9、 networking permitted without license from IHS-,-,-MIL-DTL-3970/13E 3 TABLE I. Dash number, electrical and physical characteristics, and dimensions - Continued. Flange Frequency Insertion Pressur- Dimensions 1/ 2/ 3/ Dash Wave- 1 2 range loss VSWR ization no. guide M85/ M3922/ TE10mode GHz max dB ma

10、x lbf/in2gage A B nom C D R 015 1-093 53-005 59-001 12.4 - 18.0 .07 1.04 30 2.601 (66.07) .015 (0.38) .500 (12.70) .028 (0.71) .003 (0.08) 1.750 (44.45) .063 (1.60) 017 1-018 52-002 52-002 1.12 - 1.70 - 1.05 30 7.810 (198.37) .010 (0.25) 1.116 (28.35) .106 (2.69) .028 (0.71) 3.364 (85.45) .125 (3.18

11、) 031 1-018 52-002 52-002 1.12 - 1.70 .10 1.05 1.5 14.000 (355.60) .015 (0.38) 2.000 (50.80) .160 (4.06) .029 (0.74) 8.670 (220.22) .015 (0.38) 032 1-029 52-006 52-006 1.70 - 2.60 .10 1.05 3.0 10.000 (254.00) .015 (0.38) 2.000 (50.80) .101 (2.57) .019 (0.48) 5.770 (146.56) .015 (0.38) 1/ Dimensions

12、are in inches. 2/ Metric equivalents (to the nearest .01 mm) are given for general information only and are based upon 1 inch = 25.4 mm. 3/ Metric equivalents are in parentheses. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3970/13E 4 REQU

13、IREMENTS: Dimensions and configuration: See table I and figure 1. Electrical characteristics: See table I. Part or Identifying Number (PIN): M3970/13-(dash number from table I). Cross reference: See table II. TABLE II. Cross reference. PIN M3970/13- Type designation PIN M3970/13- Type designation 00

14、1 002 003 004 005 006 007 008 UG-712/U UG-713/U UG-714/U UG-715/U UG-716/U UG-717/U UG-718/U UG-719/U 009 010 011 012 013 014 015 016 UG-720/U UG-721/U UG-722/U UG-723/U UG-724/U UG-725/U UG-726/U UG-727/U NOTE: Assemblies covered by this specification are substitutable for the following commercial

15、types: PIN Manufacturer Commercial M3970/13- CAGE code type 017 10001 2938971-1 017 01456 650BH49 017 61804 L2257 031 52564 3705001 032 52564 4005001 Referenced documents. This specification sheet only references MIL-DTL-3970. The margins of this specification sheet are marked with vertical lines to

16、 indicate where modifications from this revision were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content

17、irrespective of the marginal notations. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5985-2014-007) DLA - CC Review activities: Army - MI Navy - AS, CG, MC, OS Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-