DLA MIL-DTL-3928 19 E-2011 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (COAXIAL) (ELECTRICALLY OPERATED) CLASS 5 TR.pdf

《DLA MIL-DTL-3928 19 E-2011 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (COAXIAL) (ELECTRICALLY OPERATED) CLASS 5 TR.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-3928 19 E-2011 SWITCHES RADIO-FREQUENCY TRANSMISSION LINE (COAXIAL) (ELECTRICALLY OPERATED) CLASS 5 TR.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5985MIL-DTL-3928/19E 15 February 2011 SUPERSEDING MIL-DTL-3928/19D 15 August 2001 DETAIL SPECIFICATION SHEET SWITCHES, RADIO-FREQUENCY TRANSMISSION LINE (COAXIAL) (ELECTRICALLY OPERATED) CLASS 5, TR This specification is approved for use by all Departments and Agencies of the Department

2、 of Defense. Requirements for acquiring the switch described herein shall consist of this specification sheet and MIL-DTL-3928. Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A .35 .29 8.9 7.4 K .28 .22 7.1 5.6 B .65 .59 16.5 15.0 L .53 .47 13.5 11. 9

3、C 2.18 2.14 55.4 54.4 M .553 .537 14.0 13.6 D .45 - 11.4 - N 1.098 1.082 27.89 27.48 E .22 .16 5.6 4.1 P .640 .620 16.26 15.75 F 2.15 - 54.6 - Q .644 - 16.36 - G .154 dia .144 dia 3.91 dia 3.66 dia R .073 .053 1.85 1.35 H .35 - 8.9 - S 1.37 - 34.8 - J 1.788 1.772 45.42 45.01 T .644 - 16.36 - NOTES:

4、1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 1. PINs M39

5、28/19-02, M3928/19-08, and M3928/19-13. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 2 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless ot

6、herwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 1. PINs M3928/19-02, M3928/19-08, and M3928/19-13 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted with

7、out license from IHS-,-,-MIL-DTL-3928/19E 3 FIGURE 2. PIN M3928/19-03. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 4 Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A .200 - 5.08 - H

8、 .644 - 16.36 - B 1.53 1.47 38.9 37.3 J 1.33 1.27 33.8 32.3 C .81 .75 20.6 19.1 K .07 - 1.8 - D 1.810 1.790 45.97 45.47 L .644 - 16.36 - E .41 .35 10.4 8.9 M 1.30 1.24 33.0 31.5 F .810 .790 20.57 20.07 N 2.22 2.16 56.4 54.9 G .30 .24 7.6 6.1 NOTES: 1. Dimensions are in inches. 2. Metric equivalents

9、are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 2. PIN M3928/19-03 - Continued. POSITION 1. (DEENERGIZED OR FA

10、ILSAFE POSITION) J1-J2 AND J3-J4. POSITION 2. (ENERGIZED POSITION) J1-J3 AND J2-J4. SCHEMATIC (SHOWN IN POSITION 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 5 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given

11、 for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 3. PIN M3928/19-04. Dimensions Letter Inches Millimeters Letter Inches

12、Millimeters Max Min Max Min Max Min Max Min A 2.90 2.84 73.7 72.1 F .90 .84 22.9 21.3 B 3.25 - 82.5 - G .90 .84 22.9 21.3 C .40 .34 10.2 8.6 H 1.84 1.78 46.7 45.2 D .41 .35 10.4 8.9 J .190 dia .170 dia 4.83 dia 4.32 dia E 1.46 1.40 37.1 35.6 POS. 1. DEENERGIZED OR FAILSAFE POSITION, J1-J2 AND J3-J4

13、POS. 2. ENERGIZED POSITION, J1-J4 AND J2-J3. SCHEMATIC (SHOWN IN POSITION 1) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 6 FIGURE 4. PINs M3928/19-05, M3928/19-09, and M3928/19-14 Provided by IHSNot for ResaleNo reproduction or n

14、etworking permitted without license from IHS-,-,-MIL-DTL-3928/19E 7 Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A 1.098 1.082 27.89 27.48 L .45 - 11.4 - B .28 .22 7.1 5.6 M 1.30 - 33.0 - C .553 .537 14.0 13.6 N 1.37 - 34.8 - D 1.788 1.772 45.4 45.0

15、P .073 .053 1.85 1.35 E .900 .880 22.86 22.35 Q 2.19 2.13 55.6 54.1 F .22 .16 5.6 4.1 R .644 - 16.36 - G .25 - 6.4 - S .79 .73 20.1 18.5 H .53 .47 13.5 11.9 T .644 - 16.36 - J 1.85 - 47.0 - U .40 .34 10.2 8.6 K .159 dia .139 dia 4.04 dia 3.53 dia NOTES: 1. Dimensions are in inches. 2. Metric equival

16、ents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 4. PINs M3928/19-05, M3928/19-09, and M3928/19-14 - Conti

17、nued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 8 FIGURE 5. PIN M3928/19-06. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 9 Dimensions Letter Inches Millimet

18、ers Letter Inches Millimeters Max Min Max Min Max Min Max Min A .154 dia .144 dia 3.91 dia 3.66 dia K .45 - 11.4 - B 1.098 1.082 27.89 27.48 L 2.32 - 58.9 - C .553 .537 14.05 13.64 M .860 .840 21.8 21.3 D .53 .47 13.5 11.9 N 1.37 - 34.8 - E .28 .22 7.1 5.6 P .073 .053 1.85 1.35 F .22 .16 5.6 4.1 Q .

19、644 - 16.36 - G 2.18 2.14 55.4 54.4 R 1.30 - 33.0 - H 1.788 1.772 45.42 45.01 S .644 - 16.36 - J .49 - 12.4 - T 1.01 .95 25.65 24.13 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .

20、010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 5. PIN M3928/19-06 - Continued. SCHEMATIC, CONTROL, AND INDICATOR CIRCUIT Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

21、-MIL-DTL-3928/19E 10 FIGURE 6. PIN M3928/19-07. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 11 Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A .34 .28 8.6 7.1 M .553 .537 14.05 13.

22、64 B .35 .29 8.9 7.4 N .53 .47 13.5 11.9 C .35 .29 8.9 7.4 P .28 .22 7.1 5.6 D .65 .59 16.5 15.0 Q .015 - .38 - E 2.18 2.14 55.4 54.4 R 1.788 1.772 45.4 45.0 F .30 - 7.6 - S 1.30 - 33.0 - G 1.85 - 47.0 - T .644 - 16.36 - H .154 .144 3.91 3.66 U 1.37 - 34.8 - J .35 - 8.9 - V .644 - 16.36 - K .22 .16

23、5.6 4.1 W .066 .060 1.68 1.52 L 1.098 1.082 27.89 27.49 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decima

24、ls. 4. Round corners of case may be squared. FIGURE 6. PIN M3928/19-07 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 12 FIGURE 7. PIN M3928/19-10. Provided by IHSNot for ResaleNo reproduction or networking permitted wi

25、thout license from IHS-,-,-MIL-DTL-3928/19E 13 Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A .28 .22 7.1 5.6 L 1.098 1.082 27.89 27.48 B .28 .22 7.1 5.6 M .553 .537 14.05 13.64 C .35 .29 8.9 7.4 N .53 .47 13.5 11.9 D .65 .59 16.5 15.0 P .28 .22 7.1

26、5.6 E 2.18 2.14 55.4 54.4 Q 1.788 1.772 45.4 45.0 F .46 - 11.7 - R .644 - 16.36 - G 2.20 - 55.9 - S 1.37 - 34.8 - H .154 .144 3.91 3.66 T .066 .060 1.68 1.52 J .43 - 10.9 - U .644 - 16.36 - K .22 .16 5.6 4.1 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information

27、only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 7. PIN M3928/19-10 - Continued. Logic truth table RF position Logic signal A Pos 1 0 Pos 2 1 Pro

28、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 14 FIGURE 8. PIN M3928/19-11. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 15 Dimensions Letter Inches Millimeters Let

29、ter Inches Millimeters Max Min Max Min Max Min Max Min A .28 .22 7.1 5.6 L 1.098 1.082 27.89 27.48 B .28 .22 7.1 5.6 M .553 .537 14.05 13.64 C .35 .29 8.9 7.4 N .53 .47 13.5 11.9 D .65 .59 16.5 15.0 P .28 .22 7.1 5.6 E 2.18 2.14 55.4 54.4 Q 1.788 1.772 45.4 45.0 F .46 - 11.7 - R .644 - 16.36 - G 2.2

30、0 - 55.9 - S 1.37 - 34.8 - H .154 .144 3.91 3.66 T .066 .060 1.68 1.52 J .43 - 10.9 - U .644 - 16.36 - K .22 .16 5.6 4.1 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 m

31、m) for three place decimals and .03 (0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 8. PIN M3928/19-11 - Continued. Logic truth table RF position Logic signal A B Pos 1 1 0 Pos 2 0 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license

32、 from IHS-,-,-MIL-DTL-3928/19E 16 FIGURE 9. PIN M3928/19-12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-3928/19E 17 Dimensions Letter Inches Millimeters Letter Inches Millimeters Max Min Max Min Max Min Max Min A 1.03 .97 26.2 24.6 M 2.0

33、3 1.97 51.6 50.0 B .30 .24 7.6 6.1 N 1.635 1.615 41.5 41.0 C .49 .43 12.4 10.9 P .22 .16 5.6 4.1 D 1.03 .97 26.2 24.6 Q .40 .34 10.2 8.6 E .30 .24 7.6 6.1 R 1.65 - 41.9 - F .49 .43 12.4 10.9 S .53 .47 13.5 11.9 G .35 - 8.9 - T .28 .22 7.1 5.6 H .09 .03 2.3 0.8 U .41 .35 10.4 8.9 J 1.072 1.052 27.23

34、26.72 V .28 .22 7.1 5.6 K .08 - 2.0 - W .53 .47 13.5 11.9 L 1.135 1.115 28.83 28.32 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Unless otherwise specified, tolerances are .010 ( 0.25 mm) for three place decimals and .03 (

35、0.8 mm) for two place decimals. 4. Round corners of case may be squared. FIGURE 9. PIN M3928/19-12 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMSC N/A FSC 5985TABLE I. Electrical and performance characteristics. 1/ PIN M3928/19- Fig

36、. No. Hous-ing Frequen- cy range dc to GHz VSWR Insertion loss (dB) Isolation (dB) Switch- ing time (ms) Position indication circuit and rating Life cycles x 1000 Fail-safe or latching Operating current (A) 2/ Holding current (A) 2/ Nominal operating voltage Pickup voltage Dropout voltage Power and

37、indicator connector Weight (oz) 02N, S 03N, S 2 3 E E 12.4 18 Max 1.5:1 1.5:1 Max 0.5 0.5 Min 50 60 Max 20 20 None Yes 100 100 F F Max 1.3 .175 Max .35 .06 28 V dc 28 V dc 18 V dc 20 V dc 5 V dc 5 V dc Solder terminal Solder terminal Max 6 10 04N, S 4/ 05N, S 3/ 06N, S 5/ 4 5 6 I I I 12.4 12.4 18 1.

38、5:1 1.5:1 1.5:1 0.5 0.5 0.5 60 60 60 50 20 10 None Yes Yes 1000 100 1000 F F L .30 2.0 .030 .30 .12 0 28 V dc 28 V dc 115 V ac 20 V dc 20 V dc N/A 2 V dc 10 V dc N/A Solder terminal Solder terminal N/A 14 4 2.5 07N, S 08N, S 09N, S 7 2 5 E E E 18 18 18 1.5:1 1.5:1 1.5:1 0.5 0.5 0.5 60 60 60 20 20 20

39、 Yes None Yes 100 100 100 L F F .75 1.3 2.0 0 .35 .12 28 V dc 28 V dc 28 V dc 20 V dc 18 V dc 20 V dc - 5 V dc 10 V dc Solder terminal Solder terminal Solder terminal 6 6 4 10N, S 6/ 11N, S 6/ 12 N, S 8 9 10 E E E 18 18 18 1.5:1 1.5:1 1.5:1 0.5 0.5 0.5 60 60 60 20 20 20 None Yes None 100 100 100 F L

40、 F 1.3 1.0 1.0 .35 0 .2 28 V dc +5 V dc 7/ 28 V dc +5 V dc 7/ 28 V dc 18 V dc 20 V dc 20 V dc 5 V dc - 16 V dc Solder terminal Solder terminal Solder terminal 7 7 4 13 N, S 2 E 20 8 1.8:1 _ 1.5:1 at 18 GHz 1.3:1 0.7 _ 0.5 at 18 GHz 0.3 40 _ 60 at 18 GHz 70 20 None 100 F 1.3 .95 28 V dc 18 V dc 5 V d

41、c Solder terminal 6 14N, S 5 E 20 1.8:1 _ 1.5:1 at 18 GHz 0.7 _ 0.5 at 18 GHz 40 _ 60 at 18 GHz 20 Yes 100 F 2.0 .12 28 V dc 20 V dc 5 V dc Solder terminal 6 1/ M3928/19-01 has been deleted. 5/ Switch does not provide self cutoff of operating voltage after switching. 2/ At nominal V dc and 20 deg C.

42、 6/ Logic voltage: Logic 0 - 0 to 0.4 V dc. 3/ Transient interference (RFI). Logic 1 - 2.4 to 5.5 V dc. 4/ Explosion proof. 25 watts at 1 GHz into a 50-ohm load. 7/ +5 voltage deviation: 0.5 V dc. 18MIL-DTL-3928/19EProvided by IHSNot for ResaleNo reproduction or networking permitted without license

43、from IHS-,-,-MIL-DTL-3928/19E 19 REQUIREMENTS: Dimensions and configurations: See figures 1 through 9. RF connectors: Female connectors (4 places) shall meet the requirements of MIL-PRF-39012 and shall mate with SMA type male connectors in accordance with MIL-PRF-39012/55. Electrical and performance

44、 characteristics: See table I. RF power handling capability (average): 25 watts (minimum). Nominal impedance: 50 ohms. Termination: Open. Vibration: Method I. Operating temperature: -55 C to +85 C. Part or Identifying Number (PIN): M3928/19- (and dash number from table I). Revision letters are not used in this revision to identify changes with respect to the previous issue, due to the extensiveness of the changes. Referenced documents: In addition to MI