DLA MIL-C-0044077 C-1990 COVERALLS COMBAT VEHICLE CREWMEN-S《战车队员工作服》.pdf

《DLA MIL-C-0044077 C-1990 COVERALLS COMBAT VEHICLE CREWMEN-S《战车队员工作服》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-C-0044077 C-1990 COVERALLS COMBAT VEHICLE CREWMEN-S《战车队员工作服》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、C 1 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Research, Development, and Engineering Center, Natick, MA 01760-5019 by using the Standardization Document Improvement Proposal

2、 (DD Form 1426) appearing at the end of this document or by letter. - - MIL-C-0044077C L( H 7779906 0465149 7 H ) INCH-POUND MIL-C-O044077C(GL) 27 November 1990 USED IN LIEU OF MIL-C-44077B 3 November 1988 MILITARY SPECIFICATION COVERALLS, COMBAT VEHICLE CREhTMENS This specification is approved for

3、use by the Natick Research, Development, and Engineering Center, Department of the Army, based upon currently available technical information but it has not been approved for promulga- tion as a coordinated revision of MIL-C-44077B(GL). It is subject to modification. However, pending its promulgatio

4、n as a coordinated military specification, it may be used in acquisition. 1. SCOPE 1.1 Scope. This specification covers coveralls made of fire-resistant material, 1.2 Classification. The coveralls shall be of the following classes and sizes as specified (see 6.2). Class 1 - Olive Green 106 D Class 2

5、 - Tan 380 Schedule of sizes Short Regular Long X-Sma 11 Sma 1 1 Medium Large X-Large X-Small Small Medium Large X-Large X-Sma 1 1 Sma 1 1 Medium Large X- La r g e AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. B Provided by IHSNot for ResaleNo re

6、production or networking permitted without license from IHS-,-,-2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise speci

7、fied, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-50083 - A-A-50195 - A-A-50199 - T-T-881 - V-F-106 - JJ-W-155 - DDD-L-2

8、0 - PPP-B-636 - Bag, Plastic, Folded Garment Thread, Aramid Thread, Polyester Core, Cotton- or Polyester-Covered Twine, Cotton, Seine Fasteners, Slide, Interlocking Webbing, Textile, (Cotton, Elastic) Label: For Clothing, Equipage, and Tentage Boxes, Shipping, Fiberboard (General Use) MILITARY MIL-F

9、-10884 - Fasteners, Snap MIL-F-21840 - Fastener Tapes, Hook and Loop, Synthetic MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equipment and Equipage; General Specification For MIL-W-43685 - Webbing, Tape, Textile, Aramid Fiber MIL-T-43709 - Tape, Text

10、ile Aramid MIL-T-44100 - Thread, Para-Aramid, Spun, Intermediate Modulus MIL-C-83429 - Cloth, Plain and Basket Weave, Aramid STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes MIL-STD-129 - Marking for Sh

11、ipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-C-O04i077C 4 7777706 0465353 5 L MIL-C-O044977C(GL) (Unless otherwise indi

12、cated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of this document to the exte

13、nt specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicita

14、tion (see 6.2). I AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) I D 3951 - Standard Practice or Comercial Packaninp. (Application for copies should be addressed to the American Society for . Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187,) COLOR ASSOCIATION OF THE UNITED ST

15、ATES Standard Color Card of America Department of Defense Standard Shades for Sewing Threads (Application for color cards should be addressed to the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color . cards are not available from the Color Association, i

16、ndividual color samples may be obtained from the contracting activity or as directed by the contracting activity. ) (Non-Government standards and other publications are normally available from organizations that prepare or distribute the documents. These documents also may be available in or through

17、 libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes laws and regulations unless a specified exempt

18、ion has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.3), in accordance with 4.3. 3.2 Guide samples. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.4). Variat

19、ion from this specification may appear in the sample, in which case this specification shall govern. 3.3 Material. It is encouraged that recycled material be used when practical as long as it meets the requirements of this specification. 3 Provided by IHSNot for ResaleNo reproduction or networking p

20、ermitted without license from IHS-,-,-MIL-C-0044077C 4 99997nb 0465152 7 9 3.3.1 Basic material. The basic cloth for the class 1 coveralls shall be plain weave Olive Green 106 conforming to type II, class 3 of MIL-C-83429. The basic cloth for the class 2 coveralls shall be plain weave Tan 380 confor

21、ming to type II, class 6 of MIL-C-83429. 3.3.2 Fastener tapes, The fastener tapes shall be 1 and 2 inch wide hook and loop tapes conforming to type I, class 2 of MLL-F-21840. The color for class 1 shall be Green 3421 and for class 2 shall be Tan 380. 3.3.3 Elastic webbing. The elastic webbing shall

22、be bleached or unbleached and shall conform to type I of JJ-W-155 in the following classes (with exceptions as indicated): . Class 1 - (Except that the water repellent and mildew resistant treatments are not required) sleeve and leg bottoms Class 6 - Waist tunnel 3.3.4 Cord. The cord beading used fo

23、r welts of pocket openings and the front openings shall conform to type i, size 18 of T-T-881, 3.3.5 Webbing. The webbing for the retrieval strap tab, the retrieval strap, and holster loop shall conform to type II of MIL-W-43685 with the following exceptions: a. The webbing far the retrieval strap s

24、hall be natural in color. b. The webbing for the liner snap fastener tabs may be natural in color; however, the same color (Olive Green 106, Tan 380, or natural) must be used for all of the snap fastener tabs within a single garment. 3.3.6 Slide fasteners. The slide fasteners shall be brass with a b

25、lack chemical finish and conform to size M of V-F-106 in the following types and styles (see operation 2 of table II for length requirements): Type I, style 3 - Drop seat, and sleeve and leg side openings Type I, style 7 - All pockets Type I, style 15 - Front opening 3.3.6.1 Slide fastener tapes. Th

26、e material for the slide fastener tapes shall be aramid. The color for class 1 shall be Olive Green 106 and for class 2 shall be Tan 380. The tapes shall be of sufficient lengths to comply with respective slide fastener attachment operations. Color matching of the fastener tape under incandescent la

27、mplight at 2300 2 1OOK shall be exempt. 3.3.6.2 Colorfastness. The finished tape shall show fastness to light and laundering equal to or better than the standard sample. When no standard sample is available, the tape shall show “fair“ fastness to light after 6 standard fading hours, and “good“ fastn

28、ess to laundering. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.3.6.3 Slide fastener thongs. The slide fastener thongs shall be 1/4-inch wide tape conforming to MIL-T-43709. The color for class I shall be Olive Green 106.and for class 2 shall

29、be Tan 380. To prevent fraying, the thong tape ends shall be either seared or ultrasonically cut. 3.3.7 Thread, aramid and para-aramid. The thread shall be aramid, sizes B and E or T-35 and T-50 conforming to A-A-50195, All operations requiring the use of a LSc-2 seam type shall use either size B or

30、 T-35 thread. When the alternate LSq-2(b) seam type is used in place of the LSc-2 seam, only MIL-T-41000 thread size T-50 shall be used (excluding loopers and the 503 or 504 portion of stitching). Para-aramid spun staple thread, size T-35 conforming to MIL-T-44100, may be used as an alternate to ara

31、niid sizes B and E. The color of the thread for class 1 shall be Olive Drab 501, C.A. 66022 and for class 2 shall be Tan 380, and shall show fastness to laundering equal to or better than the standard sample. When no standard sample is available, the thread shall show “good“ fastness to laundering.

32、3.3.7.1 Polyester thread. Cotton, covered polyester core thread, conforming to ticket No. 50, 2 ply of A-A-50199 may be used as an alternate thread for bartacking. The thread for class 1 shall be dyed Olive Drab S-1, C.A. 66022, for class 2 shall be Tan 380 and shall show fastness to laundering equa

33、l to or better than the standard sample. When no standard sample is available, the thread shall show “good“ fastness to laundering. 3.3.8 Snap fasteners. The snap fasteners shall be brass, finish 2, male and female, consisting of stud and eyelet size 1 or 2 with button size 1 or 2 and . socket, conf

34、orming to style 2A of MIL-F-10884, except an uncapped button may be used to attach the socket. 3.3,9 Labels, Each coverall shall have an identification label, a size label, and instruction label, conforming to type VI of DDD-L-20. The color of the label for class 1 shall be Medium Green, Cable No. 7

35、0034, 70130, or 70131, and the color for class 2 shall be Khaki, Cable No. 70188. The fastness to laundering requirements of DDD-L-20 shall apply. 3.3.9.1 Identification label. The identification label shall conform to class 1. 3.3.9.2 Size label. The size label shall conform to class 2 and shall co

36、ntain the following information for each respective size. Descriptive information shall be printed in letters and numerals not less than 10-point and as follows: X-Small - Short X-Small - Regular X-Small - Long Height: Below 67 in. Height: From 67 ta 71 -in. Height: Over 71 in. Chest: Below 33 in. C

37、hest: Below 33 in. Chest: Below 33 in. Stock No. Stock No. Stock No. NATO Size: 6070/7484 NATO Size: 7080/7484 NATO Size: 8090/7484 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-0044077C Small - Short Height: Below 67 i Chest: From 33 to St

38、ock No. NATO Size: 6070/8494 37 in. Medium - Short Height: Below 67 in. Chest: From 37 to Stock No. NATO Size: 6070/9404 41 in. Larse- Short Height: Below 67 in. Chest: From 41 to Stock No. NATO Size: 6070/0414 45 in. X-Large - Short Height: Below 67 in. Chest: Over 45 in. Stock No. NATO Size: 6070/

39、1424 MIL-C-0044077C (GL) Small - Regular Height: From 67 to 71 in. Chest: From 33 to Stock No. NATO Size: 7080/8494 37 in. Medium - Regular Height: From 67 to 71 in. Chest: From 37 to Stock No. NATO Size: 7080/9404 41 in. Large - Regular Height: From 67 to 71 in. Chest: From 41 to Stock No. NATO Siz

40、e: 7080/0414 45 in. X-Large - Regular Height: From 67-to 71 in. Chest: Over 45 in. Stock No. NATO Size: 7080/1424 Small - Long Height: Over 71 in. Chest: From 33 to Stock No. NATO Size: 8090/8494 37 in. Medium - Long Height: Over 71 in. Chest:. From 37 to Stock No. NATO Size: 8090/9404 41 in. Large

41、- Long Height: Over 71 in. Chest: From 41 to Stock No. NATO Size: 8090/0414 45 in. X-Large - Long Height: Over 71 in. Chest: Over 45 in. Stock No. NATO Size: 8090/1424 3.3.9.3 Instruction label. The instruction label shall conform to class 3 and shall contain the following information: COVERALLS, CO

42、MBAT VEHICLE CREWMENS These coverails are of low-flammability. No other special flame resistant treatments are required. 1. Wear as outer garment or as under-layer in cold climates. 2. Pockets are designed to accommodate operational equipment and personal effects 3. Wear liner for added insulation.

43、4. Brush snow or frost from garments before entering heated shelters. 5. Dry liner and coveralls separately when damp or wet. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6. For thorough cleaning, return to laundry unit for machine washing in .

44、accordance with established procedures. Coverall may be hand laundered; make sure that all soap is thoroughly rinsed out. 7. WARNING: Launder with slide fasteners and hook and pile fasteners engaged. Do not press hook and pile fasteners. 8. DO NOT STARCH. STARCH OR ANY OTHER TREATMENT THAT LEAVES A

45、RESIDUE WILL DETERIORATE FLAME RESISTANCE. DO NOT REMOVE THIS LABEL 9. After 10 laundering cycles and thereafter, launder in accordance with Formula IX (no bleach) of TM 10-280, field laundry and Natick Formula X, fixed laundry for the treatment of anti-static agent. 3.3.9.4 Combination identificati

46、on-instruction label. The identification label (class 1) and the instruction label (class 3) may be combined into one label. When combined, the item nomenclature shall not be repeated. The combination label shall conform to the requirements of the class 3 label. 3.4 Design. The coveralls feature a d

47、rop seat with slide fastener closure at sides and hook and loop tape at top edge, a retrieval strap (loop) located at a hook and loop tape closure at lower end of back yoke, and neck tab. There are nine pockets having slide fastener openings and welt pieces (two chest patch types, two front inside h

48、anging, two thigh inside hanging, two shin inside hanging, and a left sleeve utility pocket, elastic at sleeve and leg bottoms, with slide fastener side opening, and an elastic waist tannel). 3.5 Patterns. Standard patterns which provide an allowance of 1/2 inch for all double-lapped and double-stit

49、ched seams, and 3/8 inch for all other seams, unless otherwise specified, will be furnished by the Government. The Government patterns shall not be altered in any way and are to be used only as a guide for cutting the contractors work patterns. The working patterns shall be identical to the Government patterns. 3.5.1 Pattern parts. The component parts shall be cut from the material specified below and in accordance with the pattern parts indicated. TABLE