DLA AN102901 THRU AN103000 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 250-28.pdf

《DLA AN102901 THRU AN103000 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 250-28.pdf》由会员分享，可在线阅读，更多相关《DLA AN102901 THRU AN103000 REV 3-1986 BOLT - DRILLED HEX HEAD 1 HOLE 250-28.pdf（1页珍藏版）》请在麦多课文档分享上搜索。

1、L .500 .562 .625 750 .m .812 .875 .938 1 .o62 1.OOO 1.125 1 .lea 1.250 - MATERIAL IDENTIFICATION PER . 2800. RAISED OR DEPRESSED .O10 MAX WITH SHANK WITHIN .O03 FIR. THIS-SURFACE MUST-BE-SPUARE SECTION THRU THREAD PR +.O00 PART NO. L +.O00 K K -.o60 - * O60 1.312 .562 il AN102907 i:$;$ ,688 .625 AN1

2、02906 102908 1.500 .750 .125 AN102912 1.750 1.000 (a) 102911 1.688 .938 .188 AN102913 1.875 1.125 .250 AN102914 2.000 1.250 .312 AN102915 2,125 1.375 .375* m102916 2.250 1.500 .430 AN102917 2.375 1.625 .500 ANlU29lt) 2.500 1.750 LCHAMFER 30 TO .438 DIA (OPPOSITE SIDE OPTIONAL) - ILE PART NO. L 10291

3、9 2.625 AN102920 2. 50 AN102921 2 .i75 AN102922 3.000 AN102923 3.125 AN102924 3.250 AN102925 3.375 (a) M HEAD. WIHLTM no IMPERFECT THREADS. - + . O00 K - .O60 2.000 1.875 2.125 2.250 2 375 2.500 2.625 2.750 2.875 3 .WO 3.125 3.250 3.375 3.500 - PART NO. L AN10293 4.375 AN10293: 4 -500 AN102935 4.625

4、 AN102936 4.750 AN10293 4.875 AN10293i 5.000 AN102940 5.250 AN102939 5.125 AN102941 5.375 AN102942 5.500 AN102944 5.750 AN102943 5.625 AN102945 5.875 AN102946 6.000 + . O00 PART NO. K - .o60 3.625 AN102947 3. 50 AN102948 3 .i75 AN102949 4.000 AN102950 4.125 AN102951 4,250 ANI02952 4,500 AN102954 4.6

5、25 AN102955 4.750 AN102956 5. WO AN102958 4.875 AN102957 5.1.25 AN102959 4,375 AN102953 5.250 102960 “ “ SHANK SHALL BE STRAIQHT WITHIN .O03 FIR.PER INCH OF- BOLT LENGTH. THE CONCENTRICITY OF THREAD PD IN RELATION M THE SHANK SHALL BE WITHIN .o06 FIR. THE CONCENTRICITY OF THE SHANK IN RELATION M THB

6、 WASHHR FACE DIAMETER AND HEXAOON SHALL BE WIlWIN .O13 FIR. SURFACE ROUGHNESS: AS107 WANUFACllJRIN(1 SPECIFICATION: M7452 INSPECTION: ALL PARTS SHALL UNDERGO MAGNETIC INSPECTION IN ACCORDANCE WITH AMs2040 BREW SHARP EDGES 003-.015 UNLESS OTHKRWISE SPECIFIED. DIHENSIONS IN INCHE? UNLESS OTHERWISE SPE

7、CIFIED: TOLERANCES; LINEAR DIMENSINS i.010, ANOULAR DIWSIONS i2. Do NOT USE UNASSIONED PART NUMBERS. INACTIVE FOR NEW DESIGN AFTER 3 MARCH 1969 NO SUPERSEDING STANDARD. O ! C c -3 i G b E a I a ANDARD W& DEVELOPED COOPERATIVELY BY THE ENGINE AND PROPELLER UTILITY PARTS COMMITTEE OF THE SU. i AIR FORCElNAVY AERONAUTICAL STANDARD AN1029QI P,A- AF-II CUST . NAVY - A9 ARMY-AV THRU BOLT - DRILLED HEX HEAD, 1 HOLE, ,250-28 AN I O 3000 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-