BS EN 60382-1993 Analogue pneumatic signal for process control systems《过程控制系统用模拟气动信号》.pdf

《BS EN 60382-1993 Analogue pneumatic signal for process control systems《过程控制系统用模拟气动信号》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60382-1993 Analogue pneumatic signal for process control systems《过程控制系统用模拟气动信号》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60382:1993 IEC382:1991 Analogue pneumatic signal for process control systems The European Standard EN60382:1993 has the status of a BritishStandard UDC 654.93-85BSEN60382:1993 This BritishStandard, having been prepared under the directionof the Industrial-process Measurementan

2、d ControlStandards Policy Committee, was published underthe authority of the Standards Board and comesintoeffect on 15December1993 BSI01-2000 The following BSI references relate to the work on this standard: Committee reference PCL/1 announced in BSINews, October1993 ISBN 0 580 22722 7 Cooperating o

3、rganizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises the national committees of the following countries: Austria Italy Belgium Luxembourg Denmark Netherlands Finland Norway France Portugal Germany S

4、pain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date CommentsBSEN60382:1993 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 General 3 2 Definitions 3 3 Specified values 3 Annex ZA (n

5、ormative) Other international publications quoted in this standard with the references of the relevant Europeanpublications 5 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Table 1 Range of analogue pneumati

6、c signal 4 Table 2 Supply pressure limits 4BSEN60382:1993 ii BSI 01-2000 National foreword This BritishStandard has been prepared under the direction of the Industrial-process Measurement and Control Standards Policy Committee and is the English language version of EN60382:1993 Analogue pneumatic si

7、gnal for process control systems, published by the European Committee for Electrotechnical Standardization (CENELEC). It is identical with IEC382:1991 published by the International Electrotechnical Commission (IEC). A British Standard does not purport to include all the necessary provisions of a co

8、ntract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, a

9、n inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN60382 August1993 UDC 654.93-85 Descriptors:

10、Industrial-process, measurement andcontrol, analogue signal, analogue pneumatic signal, pressure English version Analogue pneumatic signal for process control systems (IEC382:1991) Signal analogique pneumatique pour des systmes de conduite de processus (IEC382:1991) Analoges Pneumatik-Signal fr Proz

11、eleitsysteme (IEC382:1991) This European Standard was approved by CENELEC on1993-07-06. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date

12、lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

13、e responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxem

14、bourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brusse

15、ls 1993 Copyright reserved to CENELEC members Ref. No. EN60382:1993 EEN60382:1993 2 BSI 01-2000 Foreword The CENELEC questionnaire procedure, performed for finding out whether or not the International Standard IEC382:1991 could be accepted without textual changes, has shown that no common modificati

16、ons were necessary for the acceptance as European Standard. The reference document was submitted to the CENELEC members for formal vote and was approved by CENELEC as EN60382 on6July1993. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this sta

17、ndard, Annex ZA is normative. latest date of publication of an identical national standard (dop)1994-08-01 latest date of withdrawal of conflicting national standards (dow)1994-08-01EN60382:1993 BSI 01-2000 3 1 General 1.1 Scope and object This International Standard specifies the analogue pneumatic

18、 signal used in industrial-process measurement and control systems to transmit information between the elements of such systems. It is applicable to: a) pneumatic controllers; b) pneumatic transmitters and information transmission systems. This standard does not apply to analogue pneumatic signals u

19、sed entirely within an element. The object of this standard is to establish: a) a standard operating pressure range for pneumatic information transmission systems; b) a standard air supply pressure (with limit values) for the operation of pneumatic controllers and transmitters, pneumatic information

20、 transmission systems, current-to-pressure transducers, and similar devices. 1.2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid.

21、 All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Stand

22、ards. IEC654-2:1979, Operating conditions for industrial-process measurement and control equipment. Part2: Power. ISO1000:1981, SI units and recommendations for the use of their multiples and of certain other units. 2 Definitions For the purpose of this International Standard the following definitio

23、ns apply: 2.1 elements of industrial-process measurement and control systems functional units which transduce, process or transmit measured values of controlling, controlled and reference variables NOTEA valve actuator in combination with a current-to-pressure transducer, valve positioner, or a boos

24、ter relay is considered to be an element which receives the standard pneumatic transmission signal or standard electric current transmission signal. 2.2 pneumatic information transmission system a system for conveying information comprising a transmitting mechanism converting input information into

25、a corresponding air pressure, interconnecting tubing and a receiving element responsive to air pressure which develops an output directly corresponding to the input information 2.3 current-to-pressure transducer a device which receives an analogue electrical signal and converts it to a corresponding

26、 air pressure 2.4 analogue pneumatic signal a pneumatic signal, which varies in a continuous manner within its range, used in industrial-process measurement and control systems to transmit information 2.5 range of the analogue pneumatic signal the range is all the values of the signal which lie betw

27、een defined limits 2.6 lower limit the specified lowest value of the range 2.7 upper limit the specified highest value of the range 2.8 supply pressure the pneumatic pressure supply which enables the system element to generate the pneumatic signal specified in this standard and, if applicable, to pr

28、ovide the actuator of the final control element with operational force 3 Specified values NOTEAll values of pressure are given in gauge pressure. The unit for pressure in the International System of Units (SI) is the pascal (Pa), defined as one newton per square metre. Customary units for pressure a

29、re the kPa and the bar. The bar is not an SI unit but ISO1000 states that it may be used for fluid pressure. 1Pa=1N/m 2 =10 5 bar 100kPa=1bar 3.1 Range of the analogue pneumatic signal The range of the analogue pneumatic signal shall be as given in Table 1. EN60382:1993 4 BSI 01-2000 Table 1 Range o

30、f analogue pneumatic signal 3.2 Supply pressure The supply pressure limits shall be as given in Table 2. These limits are in accordance with the limit values specified in5.2.1.1 of IEC654-2. Table 2 Supply pressure limits Lower limit kPa Upper limit kPa 20 100 NOTEThe output of a controller or a cur

31、rent-to-pressure transducer may be connected directly (without using a positioner) to a pneumatic actuator for positioning a final control element with a nominal range of20kPa100kPa. Under operational conditions, if forces are exerted from the controlled medium to the final control element, a larger

32、 range is required for proper functioning. In this case, devices should be used with an output designed to vary from near zero to near supply pressure (preferably5kPa120kPa). Minimum kPa Maximum kPa 130 150EN60382:1993 BSI 01-2000 5 Annex ZA (normative) Other international publications quoted in thi

33、s standard with the references of the relevant European publications This European Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated

34、 references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. NOTEWhen the international publication has been mod

35、ified by CENELEC common modifications, indicated by (mod), the relevant EN/HD applies. IEC publication Date Title EN/HD Date 654-2 1979 Operating conditions for industrial-process measurement and control equipment Part 2: Power HD413.2S1 1981 Other publication ISO1000:1981 SI units and recommendatio

36、ns for the use of their multiples and of certain other units6 blankBSEN60382:1993 BSI 01-2000 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Industrial Process Measurement and Control Standards

37、 Policy Committee (PCL/-) to Technical Committee PCL/1, upon which the following bodies were represented: British Coal Corporation British Gas plc British Telecommunications plc Department of Trade and Industry (Gas and Oil Measurement Branch) Electricity Association Electronics Component Industry F

38、ederation Energy Industries Council Engineering Equipment and Materials Users Association GAMBICA (BEAMA Ltd.) Health and Safety Executive Institution of Gas Engineers The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Department of Health E

39、RA Technology Ltd. Institute of Measurement and Control SIRA Ltd. Department of Trade and Industry (National Weights and Measures Laboratories) National annex NB (informative) Cross-references Publication referred to Corresponding British Standard IEC654-2:1979 BS5967 Operating conditions for indust

40、rial-process measurement and control equipment Part2:1980 Specification for power ISO1000:1992 BS5555:1993 Specification for SI units and recommendations for the use of their multiples and of certain other unitsBS EN 60382:1993 IEC382:1991 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandards

41、Institution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards

42、should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical comm

43、ittee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI,

44、 international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise r

45、equested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and ser

46、vices. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:020

47、89967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a r

48、etrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade design

49、ations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.