ASTM D6496 D6496M-2004A(2015)e1 1875 Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners《测定针.pdf
《ASTM D6496 D6496M-2004A(2015)e1 1875 Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners《测定针.pdf》由会员分享,可在线阅读,更多相关《ASTM D6496 D6496M-2004A(2015)e1 1875 Standard Test Method for Determining Average Bonding Peel Strength Between Top and Bottom Layers of Needle-Punched Geosynthetic Clay Liners《测定针.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D6496/D6496M 04a (Reapproved 2015)1Standard Test Method forDetermining Average Bonding Peel Strength Between Topand Bottom Layers of Needle-Punched Geosynthetic ClayLiners1This standard is issued under the fixed designation D6496/D6496M; the number immediately following the designation
2、indicates theyear of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits information and designation were correc
3、ted editorially in July 2015.1. Scope1.1 This test method covers the laboratory determination ofthe average bonding strength between the top and bottomlayers of a sample of a geosynthetic clay liner (GCL).1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as st
4、andard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, a
5、ssociated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D76/D76M Specification for Tensile Testing Machines fo
6、rTextilesD4439 Terminology for Geosynthetics3. Terminology3.1 Definitions:3.1.1 geosynthetic, na product manufactured wholly or inpart from polymeric material used with soil, rock, earth, orother geotechnical engineering related material as an integralpart of a project, structure, or system. D44393.
7、1.2 geosynthetic clay liner, na manufactured hydraulicbarrier consisting of clay bonded to a layer or layers ofgeosynthetic material(s). (Currently being balloted under D35Committee on Terminology.)4. Summary of Test Method4.1 The top and bottom layers of a geosynthetic clay linerare gripped individ
8、ually in tensile grips and pulled at a constantrate of extension by a tensile testing machine until the top andbottom layers of the specimen separate. The average bondingpeel strength of the test specimen can be calculated frommachine scales, dials, recording charts, or an interface com-puter.5. Sig
9、nificance and Use5.1 The bonding strength test for the top and bottom layersof the geosynthetic clay liner is intended to be an index test. Itis anticipated that the results of the test will be used to evaluatethe quality of the bonding process.6. Apparatus6.1 Tensile Testing MachineA constant rate
10、of extension(CRE) type of testing machine described in SpecificationD76/D76M shall be used with a minimum precision measuringcapability of 0.1 N/m 5.71 104lbf/in.6.2 ClampsThe clamps shall be a minimum 25 by 100mm 1 by 4 in. and with appropriate clamping power toprevent slipping or crushing (damage)
11、.6.3 Die or Template, 100 by 200 mm (61 mm) 4 by 8 in.6.4 Miscellaneous, knives, razor, and the like, as required.7. Test Specimen7.1 The sample received at the testing laboratory should bein satisfactory condition and representative of the productmanufactured or delivered to a site, or both.7.2 The
12、 size of the die or template for cutting specimens is100 by 200 mm 4 by 8 in.1This test method is under the jurisdiction of ASTM Committee D35 onGeosynthetics and is the direct responsibility of Subcommittee D35.04 on Geosyn-thetic Clay Liners.Current edition approved July 1, 2015. Published July 20
13、15. Originally approvedin 1999. Last previous edition approved in 2009 as D6496 04a(2009). DOI:10.1520/D6496_D6496M-04AR15E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
14、 refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.3 The loss of clay during the specimen cutting processshould have no bearing on the results of the test.7.4 A minimum o
15、f five test specimens should be cut fromthe laboratory sample such that they are representative of theentire roll width. All specimens should be parallel to themachine direction.8. Conditioning8.1 The test specimen shall be tested as received.9. Procedure9.1 Obtain SpecimensUsing the die, or templat
16、e and razor,and other necessary apparatus, carefully cut from the labora-tory sample five test specimens. The five specimens should berandomly selected from locations on the sample, but should bedistributed across the sample. All specimens should be cutparallel to the machine direction. Using a knif
17、e or razor,separate the top and bottom layer of the GCL for the first50 6 3mm26 0.1 in.9.2 Machine Set-Up ConditionsAdjust the distance be-tween the clamps at the start of the test to 50 6 3mm2 6 0.1 in. Set the CRE at 300 mm/min. 12 in./min.9.3 Insertion of Specimen in ClampsMount the specimencentr
18、ally in the clamps. The specimen must be visuallyobserved above the clamp. The specimen length in the machinedirection must be parallel to the direction of application offorce.9.4 Measurement of Bonding Peel StrengthStart the ten-sile testing machine. This is considered the start of the peel testand
19、 represents zero grip separation. Take readings of force andtime starting from 50 mm 2 in. of grip separation until250 mm 10 in. of grip separation. The average recordedpeeling force of the GCL over 200 mm 8 in. of gripseparation is required and will signify a complete test of thespecimen. (See Fig.
20、 1).NOTE 1If significant elongation of the geotextile continues after50 mm 2 in. additional grip peeling of the GCL, the recording intervalshould be adjusted. The recording interval should correspond to 200 mm8 in. of grip separation during the peeling of the GCL.9.4.1 Readings of force and time sha
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD6496D6496M2004A2015E11875STANDARDTESTMETHODFORDETERMININGAVERAGEBONDINGPEELSTRENGTHBETWEENTOPANDBOTTOMLAYERSOFNEEDLEPUNCHEDGEOSYNTHETICCLAYLINERS

链接地址:http://www.mydoc123.com/p-522677.html